Ingersoll Rand Marine Radio 651511 X User Manual

OPERATOR’S MANUAL  
651511-X  
RELEASED: 11-24-76  
INCLUDING: SERVICE KITS, TROUBLESHOOTING, PARTS LIST,  
DISASSEMBLY & REASSEMBLY.  
REVISED:  
(REV. E)  
10-7-13  
AUTOMATIC DISPENSING VALVE  
651511-X  
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,  
OPERATING OR SERVICING THIS EQUIPMENT.  
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.  
651511 EXTRUSION  
651511-1 AIRLESS SPRAY  
A
B
C
D
F
E
G
H
F
Figure 2  
Figure 1  
GENERAL DESCRIPTION  
SPECIFICATION DATA  
651511 Extrusion  
REF.  
A - Material Outlet 11/16- 16 UN-2A  
B - Material Inlet (2) 3/8 “ PTF  
651511-1 Airless Spray  
Automatic Valve with the following features.  
C - Air Inlet 1/8NPTF (Return or "Closing")  
D - Air Inlet 1/8NPTF (Actuating)  
E - Width Dia. 2-1/2" (63.5 mm)  
F - Overall Length Approx. 8.937" (227 mm)  
G - Body Length Approx. 7-1/2" (190 mm)  
H - Mounting Hole 1/2" dia.  
The ball and valve seat are made of tungsten carbide for  
maximum resistance to erosion and wear.  
The (3) 90565 packings are made of PTFE for maximum  
wear and resistance to solvents.  
This unit has a 2” diameter air cylinder. The 72842 piston  
is made of Buna “N.  
It has a 1/2mounting hole.  
MAINTENANCE  
Both air inlets are 1/8 - 27 NPTF (female).  
Air operated opening and closing.  
With proper care, this unit will give long reliable service. To  
maintain this performance, it should be “flushed thoroughly”  
with solvent immediately following each application period if  
equipment is to be idle for a long period of time.  
OPERATING INSTRUCTIONS  
Use only genuine ARO® replacement parts to assure com-  
patible pressure rating and longest service life.  
HEED ALL WARNINGS.  
If material leakage occurs between valve housing (25)  
and body (19), check gasket (24).  
If material leakage occurs at orifice of gun, check ball and  
ball seat for dirt or foreign substance. Inspect ball and  
ball seat (23).  
WARNING  
HIGH PRESSURE DEVICE. Improper usage of this  
equipment could result in serious injury. The possibility of  
injection into the flesh is a potential hazard. Never allow  
any part of the human body to come in front of, or in direct  
contact with, the material outlet. An injection injury can be  
serious. If injection should occur, contact a qualified physi-  
cian for immediate treatment of such injuries.  
If material leakage occurs around piston rod (21) in open-  
ing of air cylinder head (13) check tightness of retainer  
(15) or worn packings (17).  
If air leakage occurs around the air cylinder, check for  
damaged or worn “O” rings. (Indicated on the drawing  
(12), (11), and (4)).  
SERVICING. Before servicing or removing fluid hose or  
valve from a unit that has been used, be sure to disconnect  
air lines and carefully bleed pressure off of the system.  
PREVENT FIRES. When pumping, flushing or recirculating  
volatile solvents, the area must be adequately ventilated.  
Keep solvents away from heat, sparks and open flames.  
Keep containers closed when not in use.  
CAUTION  
The maximum working pressure for the auto-  
matic dispensing valve assembly is 5000 p.s.i. (345 bar).  
INGERSOLL RAND COMPANY LTD  
209 NORTH MAIN STREET – BRYAN, OHIO 43506  
© 2013  
CCN 81380065  
(800) 495-0276 FAX (800) 892-6276  
 

InFocus Home Theater System IN5122 IN5124 User Manual
JVC Projection Television LCT2441 001B User Manual
JVC VCR RX 774RBK User Manual
Kenwood Car Video System KVT 837DVD User Manual
Kenwood Home Theater System KR V990D User Manual
KitchenAid Convection Oven KEBS107Y User Manual
Kolcraft Stroller S45J R7 User Manual
Kompernass Hair Dryer KH 5513 User Manual
Konica Minolta Camcorder 211 163 User Manual
Konica Minolta Printer 1250E User Manual