GE Appliances
Safety Information
Owner’s Manual &
Installation Instructions
Safety Precautions . . . . . . . . . . . . . . . .3
How to Connect Electricity . . . . . . . .3
Use of Extension Cords . . . . . . . . . . .4
Use of Adapter Plugs . . . . . . . . . . . . .4
ASC05 – 5,000 BTU models
Operating Instructions
About the Controls . . . . . . . . . . . . . . .5
Care and Cleaning
Grille and Case . . . . . . . . . . . . . . . . . . .6
Outdoor Coils . . . . . . . . . . . . . . . . . . .6
Air Filter . . . . . . . . . . . . . . . . . . . . . . . .6
Installation Instructions
Window Installation . . . . . . . . . . .7–11
Troubleshooting Tips
Before You
Call For Service . . . . . . . . . . . . . . . . .12
Normal Operating Sounds . . . . . . .12
Customer Service
Product Registration . . . . . . . . .13, 14
Warranty . . . . . . . . . . . . . . . . . . . . . . .15
Service Telephone
Numbers . . . . . . . . . . . .2, Back Cover
E DB68-01037A(2)
49-7385-1 JR 12-99
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
SafeyIructions
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock
or personal injury.
SAFETY PRECAUTIONS
■ Use this appliance only for its intended
purpose as described in this Owner’s
Manual.
■ Turn the mode control to OFF and unplug
your air conditioner before making any
repairs or cleaning.
OpeagIructions
■ This air conditioner must be properly
installed in accordance with the Installation
Instructions before it is used.
NOTE: We strongly recommend that any
servicing be performed by a qualified
individual.
■ Never unplug your air conditioner by
pulling on the power cord. Always grip
plug firmly and pull straight out from
the receptacle.
■ For your safety…do not store or use
combustible materials, gasoline or other
flammable vapors or liquids in the vicinity
of this or any other appliance.
■ Repair or replace immediately all electric
service cords that have become frayed or
otherwise damaged. Do not use a cord
that shows cracks or abrasion damage
along its length or at either the plug or
connector end.
laIructions
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
For personal safety, this appliance must be
properly grounded.
The air conditioner should always be
plugged into its own individual electrical
outlet which has a voltage rating that matches
the rating plate.
T
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall
outlet to minimize the possibility of electric
shock hazard from this appliance.
This provides the best performance and also
prevents overloading house wiring circuits
which could cause a fire hazard from
overheated wires.
rubleshotingT
See the Installation Instructions, Electrical
Requirements section for specific electrical
connection requirements.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
ips
Where a 2-prong wall outlet is encountered,
it is your personal responsibility and obligation
to have it replaced with a properly grounded
3-prong wall outlet.
CustomSrvice
3
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
USE OF EXTENSION CORDS–115-Volt models only
Because of potential safety hazards under certain
CAUTION:
DO NOT use an extension cord with any of
the 230/208 volt models.
conditions, we strongly recommend against the
use of an extension cord.
SafeyIructions
However, if you must use an extension cord,
it is absolutely necessary that it be a UL-listed,
14 gauge, 3-wire grounding type appliance
extension cord having a grounding type plug
and outlet and that the electrical rating of the
cord be 15 amperes (minimum) and 125 volts.
USE OF ADAPTER PLUGS –115-Volt models only
Because of potential safety hazards under
certain conditions, we strongly recommend
against the use of an adapter plug.
When disconnecting the power cord from
the adapter, always hold the adapter in place
with one hand while pulling the power cord
plug with the other hand. If this is not done,
the adapter ground terminal is very likely to
break with repeated use.
OpeagIructions
However, if you must use an adapter,
where local codes permit, a temporary
connection may be made to a properly
grounded 2-prong wall outlet by use of
a UL-listed adapter available at most
local hardware stores.
If the adapter ground terminal breaks,
DO NOT USE the air conditioner until a
proper ground has been established.
The larger slot in the adapter must be
aligned with the larger slot in the wall
outlet to provide proper polarity in the
connection of the power cord.
Attaching the adapter ground terminal to a wall
outlet cover screw does not ground the appliance
unless the cover screw is metal, and not insulated,
and the wall outlet is grounded through the house
wiring. You should have the circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
laIructions
ips
Read and follow this Safety Information carefully.
SAVE THESE INSTRUCTIONS
rubleshotingT
T
CustomSrvice
4
SafeyIructions
About the controls on the air conditioner.
Features and appearance will vary.
OFF
5
4
LOW
FAN
HI
FAN
3
2
6
7
OpeagIructions
HI
COOL
LOW
COOL
8
1
MED COOL
MODE CONTROL
TEMP CONTROL
Controls
laIructions
Mode Control
Temp Control
HI COOL, MED COOL and LOW COOL
provide cooling with different fan speeds.
The temp control is used to maintain the
room temperature. The compressor will
cycle on and off to keep the room at the
same level of comfort. When you turn
the knob to a higher number the indoor
air will become cooler. Turn the knob to
a lower number and the indoor air will
become warmer.
FAN settings provide air circulation and
filtering without cooling.
NOTE: If you move the switch from a cool setting
to OFF or to a fan setting, wait at least
3 minutes before switching back to a cool setting.
Cooling Descriptions
The blower runs as long as the mode
control is not on OFF.
For Normal Cooling—Select HI COOL
or MED COOL with the temp control
at midpoint.
T
rubleshotingT
For Maximum Cooling—Select HI COOL
with the temp control at the highest
number available on the knob.
For Quieter & Nighttime Cooling—Select
LOW COOL with the temp control at
midpoint.
ips
Air Direction
Fingertip pressure on the louvers adjusts the
air direction up or straight ahead.
CustomSrvice
5
Care and cleaning of the air conditioner.
Grille and Case
Turn the air conditioner off and remove the
plug from the wall outlet before cleaning.
To clean, use water and a mild detergent.
Do not use bleach or abrasives.
SafeyIructions
Outdoor Coils
The coils on the outdoor side of the air
conditioner should be checked regularly.
If they are clogged with dirt or soot they may
be professionally steam cleaned, a service
available through your GE service outlet.
OpeagIructions
Air Filter
The air filter behind the front grille should be
checked and cleaned at least every 30 days or
more often if necessary.
To remove:
Grasp the filter handle and pull it up and out.
The filter can be cleaned with a vacuum
cleaner to remove light dust or washed in
warm, soapy water. Rinse and let the filter dry
before replacing it. Do not expose the filter to
heat or direct sunlight when drying.
laIructions
CAUTION: DO NOT operate the air conditioner
without a filter because dirt and lint will clog it and
reduce performance.
ips
rubleshotingT
T
CustomSrvice
6
SafeyIructions
Preparing to install the air conditioner.
Read these instructions completely and carefully.
Before You Begin
NOTE TO INSTALLER: Leave these instructions
with the air conditioner after installation is
completed.
CAUTION:
Do not, under any circumstances, cut
or remove the third (ground) prong
from the power cord.
NOTE TO CONSUMER: Keep this Owner’s
Manual and Installation Instructions for
future use.
OpeagIructions
Do not change the plug on the power
cord of this air conditioner.
IMPORTANT NOTES:
Aluminum house wiring may present
special problems—consult a qualified
electrician.
For personal safety, this air conditioner must
be properly grounded.
It is important to have the wall outlet and
circuit checked by a qualified electrician if
there is any doubt as to whether a proper
ground exists.
Follow National Electric Codes (NEC) and/or
local codes and ordinances.
laIructions
Electrical Requirements
Some models require 115/120-volt
a.c., 60 Hz grounded outlet protected
with a 15-amp time delay fuse or
circuit breaker.
Some models require 230/208-volt
a.c., protected with a time delay fuse
or circuit breaker. These models
should be installed on their own single
branch circuit for best performance
and to prevent overloading house or
apartment wiring circuits, which could
cause a possible fire hazard from
overheating wires.
The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall
outlet you plan to use is only a 2-prong outlet,
it is your responsibility to have it replaced with
a properly grounded 3-prong wall outlet.
T
rubleshotingT
Tools You Will Need
■ Phillips-head screwdriver
■ Flat blade screwdriver
■ Ruler or tape measure
■ Scissors or knife
■ Pencil
■ Level
ips
CustomSrvice
7
Window installation instructions.
Read these instructions completely and carefully.
Parts Included
Foam top window gasket
SafeyIructions
Window sash seal
Air conditioner
OpeagIructions
Left accordion panel
Right accordion panel
Type A screws (4)
Type B screws (11)
Upper accordion
panel clamp (2)
Support bracket (2)
Window locking bracket
laIructions
Lower accordion
panel clamp (2)
ips
Read completely, then follow step-by-step.
Window Requirements
1
■These instructions are for a standard
double-hung window. You will need to
modify them for other types of windows.
rubleshotingT
T
■The air conditioner can be installed without
the accordion panels if needed to fit in a
narrow window. See the window opening
dimensions at right.
133⁄16″ min.
■All supporting parts must be secured to
firm wood, masonry or metal.
23″ to 35″
■The electrical outlet must be within
reach of the power cord. Do not use an
extension cord.
CustomSrvice
183⁄4″ min.
(Without accordion panels)
8
SafeyIructions
Storm Window Requirements
2
A storm window frame will not allow the air
conditioner to tilt towards the outside and will
keep it from draining properly. To adjust for
this, attach a piece of wood to the stool.
WOOD PIECES:
WIDTH: 2″
LENGTH: Long enough to fit inside the
window frame.
OpeagIructions
Wood
THICKNESS: To determine the thickness,
place a piece of wood on the stool to make it
1/2″ higher than the top of the storm window
frame.
1/2″ higher
than frame
Stool
Storm
window
frame
Attach securely with nails or screws provided
by the installer.
Prepare the Window and the Case
laIructions
3
Cut the window sash seal to the proper
Insert the frames for the accordion panels
A
B
length. Peel off the backing and attach
into the top and bottom mounting rails.
the adhesive side to the underside of
the window sash.
Attach the accordion panels to the side of
the case using 4 type A screws.
Type A
screws
Window sash seal
Type A
screws
T
rubleshotingT
Install the Support Brackets
4
Mark the centerline of the sill. Measure
A
and mark the locations for the support
Type B screws
Type B screws
brackets 1″ from both sides of the
centerline.
ips
Inside
Place the edges of the support brackets
Sill
B
on the 1″ marks on the sill and against the
Stool
back edge of the stool.
Attach them to the sill with two type B
screws through each support bracket.
C
CustomSrvice
Support
bracket
Outside
9
Window installation instructions.
Read these instructions completely and carefully.
Install the Air Conditioner in the Window
5
Center the air conditioner in the window
Lower the window behind the top
mounting rail. The air conditioner
should be slightly tilted to the outside.
A
B
with the bottom rail between the window
stool and the support brackets.
SafeyIructions
Lower the
window
Front
grille
Outside
Inside
Support brackets
OpeagIructions
Install the Window Accordion Panels and Locking Bracket
6
Extend the left and right accordion panels
to the vertical window sashes and attach
the top corners with two type B screws.
Use a lower accordion panel clamp on
each lower corner to trap the panels.
Attach them to the stool using 2 type
B screws.
Attach the window locking bracket with a
type B screw.
A
B
laIructions
Use an upper accordion panel clamp on
each upper side to trap the panels. Attach
them to the vertical window sash using a
type B screw on each side.
ips
Type B screws
rubleshotingT
T
Type B screws
Upper accordion
Lower accordion
panel clamp
panel clamp
CustomSrvice
10
SafeyIructions
Read these instructions completely and carefully.
Install the Window Gasket
7
Cut the foam top window gasket to the
A
window width.
Stuff the foam between the glass and the
B
window to prevent air and insects from
OpeagIructions
getting into the room.
Removal from Window
8
Turn the air conditioner off and
Remove the screws securing the
accordion panels on each side.
Close the accordion panels.
A
D
E
disconnect the power cord. Wait
5-10 minutes before moving the air
conditioner to allow the water to
drain from the coil into the base pan.
laIructions
Keeping a firm grip on the air
conditioner, raise the window and
carefully “rock” the air conditioner
backward to drain most of the pan.
Carefully lift it from the window to avoid
spilling any remaining water. Store parts
for re-use with the air conditioner.
Remove the foam gasket from between
the windows.
B
Remove the window locking bracket.
C
T
rubleshotingT
ips
CustomSrvice
11
Before you call for service…
Troubleshooting Tips
Save time and money! Review the chart below first and
you may not need to call for service.
SafeyIructions
Problem
Possible Causes
What To Do
Air conditioner
does not start
The air conditioner
is unplugged.
• Make sure the air conditioner plug is pushed
completely into the outlet.
The fuse is blown/circuit
breaker is tripped.
• Check the house fuse/circuit breaker box and replace
the fuse or reset the breaker.
Power failure.
• If power failure occurs, turn the mode control to OFF.
When power is restored, wait 3 minutes to restart the
air conditioner to prevent tripping of the compressor
overload.
Air conditioner does
not cool as it should
Airflow is restricted.
• Make sure there are no curtains, blinds or furniture
blocking the front of the air conditioner.
OpeagIructions
The temp control may
not be set high enough.
• Turn the knob to a higher number. The highest setting
provides maximum cooling.
The air filter is dirty.
• Clean the filter at least every 30 days. See the Care and
cleaning of the air condtioner section.
The room may have been hot.
Cold air is escaping.
• When the air conditioner is first turned on you need to
allow time for the room to cool down.
• Check for open furnace floor registers and cold
air returns.
Cooling coils have iced up.
• See “Air conditioner freezing up” below.
Air conditioner
freezing up
Ice blocks the air flow
and stops the air conditioner
from cooling the room.
• Set the mode control at HI FAN or HI COOL
with the temp at 1 or 2.
laIructions
ips
Normal Operating Sounds
■ You may hear a pinging noise caused by water
being picked up and thrown against the
■ Water will collect in the base pan during
high humidity or on rainy days. The water
condenser on rainy days or when the humidity is
high. This design feature helps remove moisture
and improve efficiency.
may overflow and drip from the outdoor side
of the unit.
■ The fan may run even when the compressor
■ You may hear the thermostat click when the
compressor cycles on and off.
does not.
T
T
CustomSrvice
12
™
GE Service Protection Plus
GE, a name recognized worldwide for quality and dependability, offers you
™
Service Protection Plus —comprehensive protection on all your appliances—
No Matter What Brand!
Benefits Include:
• Backed by GE
• All brands covered
• Unlimited service calls
• All parts and labor costs included
• No out-of-pocket expenses
• No hidden deductibles
• One 800 number to call
We’ll Cover Any Appliance.
Anywhere. Anytime.*
You will be completely satisfied with our service protection or you may request your money back
on the remaining value of your contract. No questions asked. It’s that simple.
Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand!
Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker
coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable
household products are protected against expensive repairs.
Place your confidence in GE and call us in the U.S. toll-free at 800-626-2224
for more information.
*All brands covered, up to 20 years old, in the continental U.S.
Cut here
✁
Please place in envelope and mail to:
General Electric Company
Warranty Registration Department
P.O. Box 32150
Louisville, KY 40232-2150
13
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
Complete and mail
your Consumer
After mailing the
registration below,
store this document
in a safe place. It
contains information
you will need should
you require service.
Our service number is
800 GE CARES
Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.
If you have questions,
or need more
Product Ownership
Registration today.
Have the peace of
mind of knowing we
can contact you in the
unlikely event of
a
information, call the
safety modification.
GE Answer Center
800.626.2000.
®
1
2 3
(800-432-2737).
Model Number
Serial Number
Important: If you did not get a registration card with your
product, detach and return the form below to
ensure that your product is registered, or register
Cut here
✁
Consumer Product Ownership Registration
Model Number
Serial Number
Mr. ■ Ms. ■ Mrs. ■ Miss ■
First
Name
Last
Name
Street
Address
Apt. #
City
E-mail Address
Zip
Code
State
Date Placed
In Use
Month
Phone
Number
_
_
Day
Year
Occasionally, we may allow selected companies to send you information.
■ Check here if you do not want this information.
14
SafeyIructions
Air Conditioner Warranty
All warranty service provided by our Factory Service Centers,
or an authorized Customer Care® technician. For service,
call 800-GE-CARES.
For The Period Of: We Will Replace:
One Year
From the date of the
original purchase
Any part of the air conditioner which fails due to a defect in materials or workmanship.
During this full one-year warranty, we will also provide, free of charge, all labor
and in-home service to replace the defective part.
OpeagIructions
Five Years
From the date of the
original purchase
Any part of the sealed refrigerating system (the compressor, condenser, evaporator
and all connecting tubing) which fails due to a defect in materials or workmanship.
During this four-year additional warranty, we will also provide, free of charge, all labor
and in-home service to replace the defective part.
What Is Not Covered:
■Service trips to your home to teach you how to use the
product.
■Replacement of house fuses or resetting of circuit
breakers.
laIructions
■Improper installation. If you have an installation problem, ■Failure due to corrosion on models not corrosion-
or if the air conditioner is of improper cooling capacity
for the intended use, contact your dealer or installer.
You are responsible for providing adequate electrical
connecting facilities.
protected.
■Damage to the product caused by improper power supply
voltage, accident, fire, floods or acts of God.
■Incidental or consequential damage to personal property
caused by possible defects with this air conditioner.
■Failure of the product resulting from modifications to
the product or due to unreasonable use including failure
to provide reasonable and necessary maintenance.
■In commercial locations labor necessary to move the
unit to a location where it is accessible for service by
an individual technician.
T
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
rubleshotingT
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
ips
Warrantor: General Electric Company. Louisville, KY 40225
CustomSrvice
15
Service Telephone Numbers.
GE Answer Center® 800.626.2000
The GE Answer Center® is open 24 hours a day, 7 days a week.
SafeyIructions
In-Home Repair Service 800-GE-CARES (800-432-2737)
Expert GE repair service is only a phone call away.
Special Needs Service 800.626.2000
800-TDD-GEAC (800-833-4322)
GE offers, free of charge, a brochure to assist in planning a barrier-free kitchen for persons
with limited mobility.
OpeagIructions
Service Contracts 800-626-2224
Purchase a GE service contract while your warranty is still in effect and you’ll receive a
substantial discount. GE Consumer Service will still be there after your warranty expires.
Parts and Accessories 800-626-2002
Individuals qualified to service their own appliances can have parts or accessories sent directly
to their homes (VISA, MasterCard and Discover cards are accepted).
laIructions
Instructions contained in this manual cover procedures to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since
improper servicing may cause unsafe operation.
ips
Service Satisfaction
If you are not satisfied with the service you receive from GE:
First, contact the people who serviced your appliance.
Next, if you are still not pleased, write all the details—including your phone number—to:
rubleshotingT
T
Manager, Customer Relations
GE Appliances
Appliance Park
Louisville, KY 40225
CustomSrvice
Printed in Korea
16
|