u s e r ’ s m a n u a l
3-Way Electronic Crossover Network
OptiX-3B w/Remote Bass Boost and Level Control
t a b l e o f c o n t e n t s
2
general features
precautions
features and specifications
system wiring
3
4-5
6
mounting and installation
noise check and system adjustment
troubleshooting
7
8
9
g e n e r a l f e a t u r e s
Blue light illuminated control panel
Rotary control knobs
12dB per octave crossover slopes
PWM power supply
Remote bass boost (0-+18dB) and level controls
Subwoofer mode switch
Variable subwoofer frequency control 40-400 Hz
Parametric "Q" control (2-20)
Variable bass boost frequency control 25-250 Hz
Subwoofer stereo/mono mode control
Variable high-pass frequency control (mid-range) 40-800Hz
Variable low-pass frequency control (mid-range) 2k-7 kHz
Band pass/ high pass selector
2
Left and right mid range phase shift control (0-180)
Variable high-pass frequency control (40-8 kHz)
X1, X10 high pass frequency multiplier-switch
High-pass, mid-range & subwoofer output level controls
Mid/high & sub RCA inputs
High, mid & sub RCA outputs
Max Variable output level controls, 7 volts
P r e c a u t i o n s
To prevent short circuits, be sure to disconnect the negative battery ground lead before wiring the system up.
When you finish the installation, be sure to make one more check to be sure everything is done correctly.
Reinstate all car parts that were removed.
3
Reconnect the negative battery ground lead.
f e a t u r e s a n d s p e c i f i c a t i o n s
4
f e a t u r e s a n d s p e c i f i c a t i o n s
1. BASS BOOST CONTROL This control adjusts the bass boost gain (0 to +18dB).
Adjustable Bass Boost
Frequency
2. BASS BOOST LEVEL CONTROL This control sets the subwoofer gain control.
25Hz-250Hz
0-18dB
2-20
3. SUBWOOFER MODE SWITCH Allows subwoofer mode channel to receive signal from either the mix of from low-pass inputs
directly (when head unit has appropriate 5ch/6ch outputs).
Adjustable Bass Boost
Adjustable Q Control
Selectable Crossover
Frequency
4. VARIABLE SUBWOOFER FREQUENCY By turning the selector you can choose the subwoofer crossover points from 40Hz-400Hz.
CONTROL 40Hz-400Hz
5. PARAMETER "Q" CONTROL 2-20 Allows independent continuous change of the boost frequency bandwidth (Q-factor) for each band
from Q=20 (Narrow bandwidth, steep slope) to Q=2 (Wide bandwidth, gentle slope).
6. VARIABLE SUBWOOFER BASS BOOST By turning the selector you can choose the subwoofer crossover bass boost points from 25Hz-
FREQUENCY CONTROL 25Hz-250Hz 250Hz.
-High Pass
40Hz-8KHz
7. SUBWOOFER STEREO/MONO MODE For selection of stereo or mono mode subwoofer output.
CONTROL
-Mid High Pass
40Hz-800Hz
8. SUBWOOFER OUTPUT LEVEL CONTROL For adjusting the subwoofer channel output level.
-Mid Low Pass
2KHz-7KHz
9. VARIABLE HIGH-PASS (MID-RANGE) By turning the selector you can choose the high-pass crossover points from 40Hz-800Hz.
FREQUENCY CONTROL 40-800Hz
5
-Subwoofer (Low Pass)
Power Supply
40Hz-400Hz
10. VARIABLE LOW-PASS (MID-RANGE) By turning the selector you can choose the low-pass crossover points from 2KHz-7KHz.
FREQUENCY CONTROL 2KHz-7KHz
10-16V DC, negative ground
10K Ohm
11. BAND PASS/HIGH PASS SELECTOR When this switch is in high pass mode, the low pass filter cannot be used. It can convert rear
channel to band pass in tri amp system.
Input Impedance
S/N ratio
12. LEFT AND RIGHT HIGH & LOW PASS Allows you to change the phase of your high and low crossover from 0 to 180 degrees to help
more than 85dB
12dB/Octave
7.0V/RMS
PHASE SHIFT CONTROL 0-180 compensate for timing difference between drivers.
13. MID-RANGE OUTPUT LEVEL CONTROL For adjusting the mid-range channel output level.
Slope Rate
14. VARIABLE HIGH-PASS FREQUENCY By turning the selector you can choose the high-pass crossover points from 40Hz-800Hz.
Max Output Signal Level
Channel Separation
Distortion
CONTROL 40-8KHz
15. FREQUENCY MULTIPLIER (x1/x10 HIGH- This switch changes crossover points from 40Hz-800Hz to 400Hz-8KHz for high frequency high
60dB
PASS CROSSOVER) channel drivers.
less than 0.05%
6x12-11/16x1-3/4
(150 x 322 x 45)
16. HIGH-PASS OUTPUT LEVEL CONTROL For adjusting the high pass channel output level.
17. SUBWOOFER INPUT PORT To be connected to the subwoofer outputs of the source unit.
18. MID/HIGH INPUT PORT To be connected to the outputs of the source unit.
Dimensions,WxDxH,inches
(millimeters)
REMOTE CONTROL UNIT
1.BASS BOOST
This control sets the Bass Boost Gain from 0 to +18dB.
19. SUBWOOFER OUTPUT PORT To be connected to the subwoofer channel amplifier left/right inputs.
20. MID OUTPUT PORT To be connected to the rear channel amplifier left/right inputs.
21. HIGH PASS OUTPUT PORT To be connected to the front channel amplifier left/right inputs.
22. REMOTE CONTROL JACK Plug the modular telephone style cord connected to the remote control unit into this jack.
23. POWER TERMINALS Use these connectors to deliver power, ground, and remote turn-on control to the unit.
2.BASS LEVEL
This control sets the subwoofer level control.
S y s t e m w i r i n g
6
SUB MODE SELECTOR
SWITCH
POSITION
DIRECT
VIA INPUT
OUTPUT
SUBWOOFER
OFF
ON
SOURCE
FRONT
REAR
MIX
FRONT
REAR
ON
OFF
Subwoofer mode switch: allows sub-woofer mode channel to receive signal
from either, the mix of from front inputs, the direct from rear inputs.
M o u n t i n g a n d i n s t a l l a t i o n
Your new Opti Series Crossover comes complete with all required mounting hardware.
Mark the location for the mounting screw holes by positioning the Crossover where you wish to install
it and use a scribe (or one of the mounting screws) inserted in each of the mounting holes to mark the
mounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felt
tip pen.
Before attempting to drill the mounting holes, take note of any wires, lines or other devices in your
vehicle which may be located behind the mounting surface! Then drill pilot in the mounting surface
for the mounting screws and insert then. Tighten the screws securely.
Installation
• A red 18 gauge stranded or heavier and insulated wire should be connected to the terminal marked +12V.
Wire an in-line fuse holder on this lead as it is the 12 Volts DC wire for the system. This wire should
be connected to your vehicle’s battery. If a wire is run directly to the battery make sure to install an in-
line fuse on this wire within 12” from the battery.
7
• A black stranded wire of at least 18 gauge should be connected to the terminal marked Ground. This is
the ground wire for the X-3B and should be attached to the same ground point with the amplifiers in the
system. Keeping this ground wire as short as possible improves the electrical circuit and keeps ground
related noise problems to a minimum.
• An orange stranded wire of a least 20 gauge should be connected to the terminal marked Remote. This
wire connects to your head unit’s remote out or power antenna lead out. This wire should supply 12 Volts
DC any time the radio, cd or cassette are playing. This lead must also be connected to any other components
in your system that utilize a remote turn-on lead for powering up.
• Connect all line inputs and outputs using high-quality RCA-RCA cables.
• Recheck all connections before powering up.
• Set all level controls to their least sensitive positions and set all crossover controls, switches, etc. to the
desired frequency or position.
• Once the system is powered up, set the volume control on the head unit to about the 2 o'clock position,
and then set all the amplifiers' level controls for half output level.
N o i s e c h e c k a n d s y s t e m a d j u s t m e n t
NOISE CHECK
Check the entire audio system for noise before permanently securing the CROSSOVER mounting
1. Start the engine.
2. Turn the audio system on.
3. Rev the engine and vary the VOLUME of the audio system to determine if there is any unwanted noise.
If so, turn both the audio system and the engine off. Do not secure the CROSSOVER mounting screws. Refer to the "Trouble Shooting Guide" at this
manual.
4. If the audio system does not have any noise, securely tighten the CROSSOVER mounting screw and double check the wiring cables for safe placement.
SYSTEM ADJUSTMENT
8
Preliminary Adjustments
Pre-setting the system provides a necessary starting point for fine-tuning the entire audio system to maximum performance.
NOTE: DO NOT MOUNT CROSSOVER UNTIL THE FOLLOWING PROCEDURES HAVE BEEN COMPLETED.
1. Preset each amplifier input gain adjustment at the amplifier to half of maximum.
2. Before turning the audio system on, preset-adjust the high, mid and sub-woofer output level controls.
3. Slowly turn the volume up and listen carefully for: obvious trouble in sound (distortion, no sound, no hiss, total silence). Turn the system off refer to
"Trouble Shooting Guide" at this manual.
Caution
DO NOT ROUTE AUDIO CABLES AND POWER CABLES TOGETHER! THIS CAN CAUSE ENGINE NOISE IN YOUR AUDIO SYSTEM.
ALWAYS DISCONNECT THE SYSTEM FROM THE BATTERY BEFORE ATTEMPTING TO MAKE OR ALTER ANY CONNECTIONS. THIS
PRODUCT IS DESIRED FOR USE IN ANY 12 VOLTS NEGATIVE GROUND ELECTRICAL SYSTEM ONLY. INSTALLING THIS PRODUCT
IN ANY POSITIVE GROUND ELECTRICAL SYSTEM COULD SERIOUSLY DAMAGE THE AUDIO SYSTEM.
T B O U B L E S H O O T I N G G U I D E
POSSIBLE CAUSE
PROBLEM
1. There is an audible distortion at a low
volume level.
• Output levels NOT set correctly.
• Crossover frequencies NOT set correctly.
• Check for shorts on the speaker leads.
2. A whining sound can be heard through the • Check the red power wire. It muse be
speakers when the audio system is at low connected directly to the battery.
volume with the engine running. The whining • Check the system's ground point It muse
9
noise remains unchanged or seems to
disappear when the volume level is
increased.
make good contact with chassis ground
(bare metal).
• The radio and the CROSSOVER must be
grounded at the same reference point.
3. There is a "motor boating" type of sound
when the engine is running and the audio
• Check the red power wire. It must be
connected directly to the battery.
system volume is set at a reasonably high • Check the system's ground point. It must
level.
make good contact with chassis ground
(bare metal).
4. High squeal noise from speakers
• This is almost always caused by a poorly -
grounded RCA patch cord.
l i m i t e d w a r r a n t y p o l i c y
C r o s s o v e r
All Lanzar Signal Processors are carefully constructed and thoroughly tested
before shipment. Units purchased in the USA are warranted to be free of defects
in material and workmanship for three (3) years from the date of purchase. This
warranty is limited to the original retail purchaser of the Signal Processor.
You must also include the following items with your return:
• A copy of your sales receipt or other proof of purchase
• A brief letter indicating the problem you are experiencing with the
product
• Include in your letter your return address, daytime phone number
and RA Number
• Also include a check or money order for $20.00 for return shipping,
handling and insurance, or provide your VISA/MasterCard number
with expiration date.
Should the unit fail due to a factory defect in material or workmanship, your unit
will be repaired or replaced at the sole discretion of Lanzar.
To obtain warranty service, you must first call our Consumer Return Hotline
number at (718) 236-6948 to obtain a Return Authorization (RA) number. This
RA Number must appear on the outside of your package and on all paperwork
relating to your return.
Our obligation under this warranty is limited to the repair or replacement
of the defective unit when it is returned to us prepaid. This warranty will
be considered void if the unit was tampered with, improperly serviced,
or subject to misuse, neglect or accidental damage.
When returning the unit to us for warranty service, it must be carefully packed
and shipped prepaid to:
All implied warranties of merchantability and fitness for a particular
purpose are limited in duration to the length of the warranty. Lanzar
expressly disclaims any liability for incidental or consequential damages
caused by product defects. This warranty does not cover any expense
incurred in the removal and/or reinstallation of the Signal Processor.
Lanzar’s total liability will not exceed the purchase price of the Signal
Processor.
R.A. # ______________
Lanzar Service Center
1600 63rd Street
Brooklyn, NY 11204
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
w w w . l a n z a r . c o m
|