Raid SATA-150+USB2.0
Combo Low Profile PCI
User Manual
English
LINDY No. 70536
www.LINDY.com
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH
-
FIRST EDITION (November 2004)
Provides RAID 1 (Mirroring) to protect the data from a disk failure by writing
identical data on 2 drives.
Fully compliant with Serial ATA 1.0 specifications.
Independent 256-byte FIFOs (32 bit * 64 deep) per Serial ATA channel for host
reads and writes.
Supports Spread Spectrum in receiver.
Features Serial ATA to PCI interrupt masking.
Features Watch Dog Timer for fault resiliency.
1.1.3. USB Interface
Provides three USB2.0 / USB1.1 ports ( 3 External + 2 Internal).
Compliant with Universal Serial Bus Specification Revision 2.0 (Data Rate
1.5/12/480 Mbps).
Compliant with Open Host Controller Interface Specification for USB Rev 1.0a.
Compliant with Enhanced Host Controller Interface Specification for USB Rev
0.95, All USB ports can handle high-speed (480 Mbps), full-speed (12 Mbps),
and low-speed (1.5 Mbps) transaction.
1.2. Package Contents
Low Profile PCI Combo Host Adapter
This User’s Manual
Driver Diskette
2. What Is RAID
RAID - Redundant Array of Independent Disks
RAID technology manages multiple disk drives to enhance I/O performance and provide
redundancy in order to withstand the failure of any individual member, without loss of
data. This card provides two RAID Set types, Striped (RAID 0) and Mirrored (RAID 1).
Disk Striping (RAID 0)
Striping is a performance-oriented, non-redundant data mapping technique. While Striping
is discussed as a RAID Set type, it is actually does not provide fault tolerance. With
modern SATA bus mastering technology, multiple I/O operations can be done in parallel,
enhancing performance. Striping arrays use multiple disks to form a larger virtual disk.
- 3 -
Disk Mirroring (RAID 1)
Disk mirroring creates an identical twin for a selected disk by having the data simultaneously
written to two disks. This redundancy provides instantaneous protection from a single disk
failure. If a read failure occurs on one drive, the system reads the data from the other
drive.
3. RAID BIOS Installation
Creating and deleting RAID sets is a function found in the BIOS. During boot up, the RAID
setting message will appear and pause for a few moments to allow the user to choose what
to do.
This board will act as normal NON-RAID card when BIOS not configured for RAID. Just
proceed to Software Installation section directly.
If you use traditional parallel ATA HDD, make sure your hard drives be set up as master
mode before the RAID setting.
3.1. Creating Striped Sets (RAID 0)
1. As the BIOS boots, Press CTRL+S or F4 to enter the raid bios utility.
2. Select Create RAID set. Press Enter.
3. Select Stripe then press Enter.
4. Select Auto configuration. Press Enter.
5. Press Y to save your settings.
6. Press CTRL+E and then press Y to exit the setup.
7. Continue with conventional Fdisk and Format steps as if you are installing a conventional
hard drive.
8. Your RAID configuration is complete. Please proceed to software installation section.
3.2. Creating Mirrored Sets (RAID 1)
1. As the BIOS boots, Press CTRL+S or F4 to enter the raid bios utility.
2. Select Create RAID set. Press Enter.
3. Select Mirrored then press Enter.
4. Select Auto configuration. Press Enter.
5. Press Y to save your settings.
- 4 -
6. Press CTRL+E and then press Y to exit the setup.
7. Continue with conventional Fdisk and Format steps as if you are installing a conventional
hard drive.
8.Your RAID configuration is complete. Please proceed to software installation section.
3.3. Deleting RAID Sets
1. As the BIOS boots, Press CTRL+S or F4 to enter the raid bios utility.
2. Select Delete RAID set. Press Enter.
3. Answer Y to remove the RAID set. If the RAID set being deleted is a Striped set, then all of
the data will be lost. If the set being deleted is a Mirrored set, then the data will remain
intact and accessible on both drives.
3.4. Rebuilding Mirrored Sets
1. After replacing the failed hard drives boot the BIOS, Press CTRL+S or F4 to enter the
raid bios utility.
2. Select rebuilding Mirrored set. Press Enter.
3. Select Online rebuild or Offline rebuild.
3. Answer Y to rebuild the Mirrored set of hard drive.
3.5. Resolving Conflict
When a RAID set is created, the metadata written to the disk includes drive connection
information (Primary and Secondary). If, after a disk failure, the replacement disk was
previously part of a RAID set (or used in another system), it may have conflicting
metadata, specifically in reference to the drive connection information. If so, this
will prohibit the RAID set from being either created or rebuilt, In order for the RAID set
to function properly, this old metadata must be first overwritten with the new metadata.
To resolve this, select Resolve Conflicts, and the correct metadata, including the correct
drive connection information, will be written to the replacement disk.
4. Software Installation
4.1. Windows 2000 /XP Fresh OS installation
- 5 -
Follow the instructions in this section if you are performing a new installation of Windows
2000/XP, and you wish to boot from a device attached to the SATA port.
1. Power off the system. Insert Combo Card into an available PCI slot. Connect serial ATA
cable(s) between the SATA port and serial ATA device(s). Power up the system.
2. Put your Windows 2000/XP CD into the CD-ROM/DVD drive, or the 2000 boot diskette
#1 in the floppy drive if your system cannot boot from the CD.
3. Press F6 for third party SCSI or driver installation at the beginning of text mode
installation. Press 'S' when setup asks if you want to specify an additional device,
and insert the driver diskette. Press 'Enter' and select 'Silicon Image SiI 3X12
SATARaid Controller for Windows NT 4.0 and
3X12 SATARaid Controller for Windows XP'.
2000', or 'Silicon Image SiI
4. Press 'Enter' again when prompted to continue on with text mode setup.
5. Follow the setup instructions to select your choice for partition and file system.
6. After setup examines your disks, it will copy files from the CD to the hard drive selected
above and restart the system. After restart the setup process will resume to finish the
installation.
7. Once the operating system installation has completed you can follow the instructions
in section 4.4 to verify controller was installed correctly.
4.2. Windows 2000 installation
1. Power off the system. Insert Combo Card into an available PCI slot. Power up the
system.
2. During OS boot up, Windows will display the 'Found New Hardware Wizard'. 'Universal
Serial Bus (USB) controller', click 'Next'.
3. Select 'Search for a suitable driver for my device (Recommended)' and click 'Next'.
4. Under 'Optional search locations' insure that 'Floppy disk drives' is only checked.
5. Insert the diskette Driver into Floppy disk drives and click 'Next'.
6. When the wizard indicates that it found a driver for the device click 'Next'.
7. The wizard will now copy the required files to the system and start the Driver. After starting
the driver the wizard will display a completion dialog, click 'Finish' to exit the wizard.
8. Windows will display the 'Found New Hardware Wizard'. 'Mass Storage Controller',
click 'Next'.
9. Select 'Search for a suitable driver for my device (Recommended)' and click 'Next'.
10. Under 'Optional search locations' insure that 'Floppy disk drives' is only
checked. Click 'Next'.
11.When the wizard indicates that it found a driver for the device click 'Next'.
12. If the 'Digital Signature Not Found' dialog appears, click 'Yes' to continue
- 6 -
installing the driver.
13. The wizard will now copy the required files to the system and start the Driver. After
starting the driver the wizard will display a completion dialog, click 'Finish' to exit
the wizard.
4.3. Windows XP installation
1. Power off the system. Insert Combo Card into an available PCI slot. Power up the
system.
2. During OS boot up, Windows will display the 'Found New Hardware Wizard'.
'Universal Serial Bus (USB) controller'.
3. Select 'Install the software automatically (Recommended)' and insert diskette
driver into Floppy disk drives. And click 'Next'.
4. If the 'Hardware Installation' dialog appears, click 'Continue Anyway'.
5. The wizard will now copy the required files to the system and start the Driver. After
starting the driver the wizard will display a completion Dialog, click 'Finish' to exit
the wizard.
6. Windows will display the 'Found New Hardware Wizard'. 'Mass Storage Controller'.
7. Select 'Install the software automatically (Recommended)'. Click 'Next'.
8. If the 'Hardware Installation' dialog appears, click 'Continue Anyway'.
9. The wizard will now copy the required files to the system and start the Driver. After
starting the driver the wizard will display a completion Dialog, click 'Finish' to exit
the wizard.
4.4.Verifying The installation under Windows 2000 and XP
Follow the instructions in this section to verify that the controller was installed
correctly.
1. Right click on 'My Computer' icon, select 'Properties', left click on 'Hardware'
tab, and then on 'Device Manager' button.
2. Double click on 'System devices', then left click on 'PCI standard PCI-to-PCI
bridge '. If there is no yellow '!' or '?' in front of 'PCI standard PCI-to-PCI bridge' the
driver has started correctly.
3. Double click 'Universal Serial Bus Controllers', If there is no yellow '!' or '?' in front of
NEC PCI to USB Enhanced Host Controller
NEC PCI to USB Open Host controller
NEC PCI to USB Open Host controller
USB Root Hub
- 7 -
USB Root Hub
The driver has started correctly.
4. Double click on 'SCSI and RAID Controllers', if there is no yellow '!' or '?' in front of
'Silicon Image SiI 3112 SATARaid Controller' the driver has started correctly.
5. To view information about the devices attached to the controller, right click the 'Devices'
and select Properties from the context menu, then select the tab labeled 'General'.
4.5. Windows 98 SE /ME Fresh OS installation
Follow the instructions in this section if you are performing a new installation of Windows
98SE/ME, and you wish to boot from a device attached to the SATA port.
You may start up the Windows 98SE/ME installation from CD. If either your Windows
98SE/ME CD or CD-ROM drive is not bootable, your can start up with floppy diskettes.
1. Power off the system. Insert Combo card into an available PCI slot. Connect serial ATA
cable(s) between the SATA port and serial ATA device(s). Power up the system.
2. Put your Windows 98SE/ME CD into the CD-ROM/DVD drive, and the Windows
98SE/ME boot diskette in the floppy drive if your system cannot boot from the CD.
3. Follow the normal Windows 98SE/ME setup instructions to select your choice for
partition and file system.
4. Wait until Windows 98SE/ME finishes installing devices, regional settings, networking
settings, components, and final set of tasks, reboot the system.
5. After the system reboots, right click on 'My Computer' and select 'Properties'. From
'System Properties ', select 'Device Manager', right click on the '?PCI RAID
controller' and select 'Properties' from the context menu.
6. Click 'Driver', 'Update Driver' and select 'Automatic search for a better driver
[Recommended] '. Insert the driver diskette into floppy drive. Click 'Next' and complete
the driver installation.
7. System will go through the enumeration process and install the driver. At the end of the
process, click 'Yes' to reboot your system.
8. See instructions in section 4.8 to verify controller was installed correctly.
4.6. Windows 98SE installation
1. Power off the system. Insert Combo Card into an available PCI slot. Power up the
system.
2. During the system boot up, the Hardware Wizard will display that it found a 'PCI
- 8 -
standard PCI-to-PCI bridge', click 'Next'. Select 'Search for the best driver for your
device [Recommended]' and click 'Next'.
3. Select 'Floppy disk drives' and click 'Next'.
4. When the wizard indicates that it found a driver for the device click 'Next'. Then click
'Finish' to exit the wizard.
5. The Hardware wizard will display that it found 'NEC USB Open Host Controller',
click 'Next'.
6. Select 'Search for the best driver for your device (Recommended)' and click 'Next'.
7. Select 'Floppy disk drives'. And insert diskette driver into Floppy drive, and click 'Next'.
8. Select 'The Updated driver (Recommended)'. NEC USB Open Host Controller, and click
'Next'. Then click 'Next' to continue.
9. If display 'Insert Disk' (please insert the disk labeled windows 98 second Edition
CD-ROM) and click OK, Then click 'Finish' to exit the wizard.
10.The Hardware wizard will display that it found 'NEC USB Open Host Controller',
and click 'Next'.
11. Select 'Search for the best driver for your device (Recommended)'.
Click 'Next'.
12. Select 'Floppy disk drives' click 'Next', select 'The Updated driver
(Recommended)' NEC USB Open Host Controller, and click 'Next'. Then click 'Next'
to continue.
13.If display 'Insert Disk' (please insert the disk labeled windows 98 second Edition
CD-ROM) and click OK, then click 'Finish' to exit the wizard.
14. The Hardware wizard will display that it found 'PCI Universal serial Bus', and click
'Next'.
15.Select 'Search for the best driver for your device (Recommended)'. Click 'Next',
16.Select 'Floppy disk drives' and click 'Next', select 'The Updated driver
(Recommended)' NEC PCI To USB Enhanced Host Controller, and click 'Next'.
17. When the wizard indicates that it found a driver for the device, click 'Next'. Then click
'Finish' to exit the wizard.
18. The Hardware Wizard will display that it found a 'PCI Raid Controller', click
'Next'.
19. Select 'Search for the best driver for your device [Recommended]' and click
'Next'.
20. Make sure the 'Floppy disk drives' checkbox is checked and click 'Next'. Then click
'Next' to continue.
21. System will go through the enumeration process and install the driver.
At the end of the process, click ' Finish' to complete the installation.
Reboot the system if your Windows 98SE drive is connected on the
- 9 -
SiI 3112 Controller.
4.7. Windows ME installation
1. Power off the system. Insert Combo Card into an available PCI slot. Power up the
system.
2. During the system boot up, the Hardware Wizard will display that it found 'PCI standard
PCI-to-PCI bridge', select 'Automatic search for a better driver (Recommended)',
click 'Next'. Then click 'Finish' to exit the wizard.
3. The Hardware wizard will display that it found 'PCI Universal Serial Bus'. Select
'Automatic search for a better driver (Recommended)', insert diskette driver into
Floppy drives, and click 'Next', then click 'Finish' to exit the wizard.
4. The Hardware Wizard will display that it found a 'PCI Raid Controller', select
'Automatic search for a better driver (Recommended)'. Click 'Next'.
5. System will go through the enumeration process and install the driver. At the end of the
process, click 'Finish' to complete the installation. Reboot the system if your
Windows ME drive is connected on the SiI 3112 Controller.
4.8.Verifying The installation under Windows 98SE and ME
Follow the instructions in this section to verify that the controller was installed
correctly.
1. Right click on 'My Computer' icon, select 'Properties', left click on 'Device Manager'
tab.
2. Double click on 'System devices', then left click on 'PCI standard PCI-to-PCI bridge'. If
there is no yellow '!' or '?' in front of 'PCI standard PCI-to-PCI bridge' the driver has
started correctly.
3. Double click 'Universal Serial Bus Controllers', If there is no yellow '!' or '?' in front of
NEC PCI to USB Enhanced Host Controller
NEC USB Open Host controller
NEC USB Open Host controller
USB Root Hub
USB Root Hub
The driver has started correctly.
4. Double click on 'SCSI Controllers', If there is no yellow '!' or '?' in front of 'Silicon
Image SiI 3112 SATARaid Controller', the driver has started correctly.
5. To view information about the devices attached to the controller, right click the
'Devices' and select Properties from the context menu, then select the tab labeled
- 10 -
'General'.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operations.
- 11 -
|