3. Do not locate in unusual cooling conditions, such as
on an outside wall, or one separating an unheated
room, or in drafts from stairwells, doors, or windows.
4. Do not locate in a damp or humid area. This can
shorten thermostat life due to corrosion.
5. Do not locate where air circulation is poor, such as in
a corner, alcove, or behind an open door.
INSTALLATION AND OPERATING
INSTRUCTIONS
6. Do not install until all construction work and painting
have been completed.
LUX PRODUCTS CORPORATION
Mt. Laurel, New Jersey 08054, USA
LUXPRO
2) TOOLS REQUIRED
3
Wirestripper or knife, drill with ⁄16" bit, screwdriver,
level and a pencil.
3) REMOVING OLD THERMOSTAT
PSM40SA
HEATING & COOLING THERMOSTAT
Please read all instructions carefully. As you complete
each step, check the adjoining square ■✓.
ATTENTION : not for use with
compressors without
■ Disconnect electricity and turn off gas to the heater.
■ Remove cover from old thermostat.
52047
time delays.
■ Disconnect wires from thermostat, making sure they
do not fall back inside the wall. Make note of wires
and to which terminals they are attached as you
disconnect them. For example: “Yellow wire to
terminal Y, Red wire to terminal RH,” etc.
SPECIFICATIONS
ELECTRICAL RATING ......24 Vac (30 Vac Maximum)
3
■ Strip insulation ⁄8" from wire ends and clean off any
corrosion.
■ Loosen all screws on the old thermostat and remove
it from the wall.
■ Fill wall opening with non-combustible insulation to
prevent drafts from affecting thermostat.
SWITCH ACTION......................Open contact switch
ANTICIPATOR RATING
(HEATING)....................................0.15A to 1.2A
(COOLING)...................................Fixed 24 VAC
4) INSTALLING NEW THERMOSTAT
TEMPERATURE RANGE .......................50°F to 90°F
■ Place new decorative wall plate (if supplied), Figure 4,
over wall opening. Decorative wall plate can
optionally be left off.
INSTALLATION & OPERATION
1). THERMOSTAT LOCATION
■ Remove Front Cover of new thermostat by inserting a
finger in the side of the thermostat and gently prying
away each corner. Remove Base, Figure 2, from Sub-
Base, Figure 3, by loosening three captive screws.
■ Place Sub-Base, Figure 3, on wallplate over wall
opening. Mark wall with pencil at mounting holes as
shown in Figure 2. Now lay wallplate and Sub-Base to
the side.
■ Drill two holes with 3/16” bit, 1” deep.
■ Insert plastic screw anchors into drilled holes, flush
with wall surface.
■ Bring wires through large hole in decorative wall plate
and through Hole For Wires in Sub-Base.
For accurate temperature control and comfort, correct
location is very important. On new installations, the
guidelines listed below should be followed as closely as
possible. When replacing an old thermostat, install the
new one in the same location unless these conditions
suggest otherwise.
1. Locate the thermostat on an inside wall about five
feet above the floor, where it is easy to install and
adjust. It should be in a room that is used often, such
as a family room.
2. Do not install it where there are unusual heating
conditions, such as direct sunlight, close to a lamp,
radio, television, radiator, register, near a fireplace, or
other heat producing appliance. Also, check for hot
water pipes within the wall, or a stove on the other
side of the wall.
■ Referring to your notes and the following diagrams,
attach wires to terminal screws shown in Figure 2.
Make sure bare metal wires do not touch each other.
Push all excess wire back into wall.
© 2007 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED
1
These diagrams below are provided for new installations or unreferenced wires.
TYPICAL HOOKUP FOR 2-WIRE
24V HEATING SYSTEM AND
MILLIVOLT SYSTEM
TYPICAL HOOKUP FOR 3-WIRE
HEAT SYSTEM IF THIRD
WIRE IS FAN WIRE
TYPICAL COOLING AND
HEATING SYSTEM
(4-WIRE)
G
Y
W RH
B
O
RC
G
Y
W RH
B
O
RC
G
Y
W RH
B
O
RC
GAS
VALVE
GAS
VALVE
GAS
VALVE
FAN
FAN
COOL
COMP
24 VAC
TRANSFORMER
OR
24 VAC HEAT
24 VAC
TRANSFORMER
TRANSFORMER
110
THERMOPILE
110
110
Figure 9
Figure 8
Figure 10
TYPICAL SINGLE-STAGE
HEAT PUMP WIRING
TYPICAL COOLING AND
HEATING SYSTEM
(5-WIRE)
G
Y
W
RH
B
O
RC
G
Y
W RH
B
O
RC
ADD
JUMPER
ALT.
BETWEEN
Y & W
CHG.
FAN
GAS
VALVE
FAN
OVER
REMOVE
JUMPER
BETWEEN
RH & RC
COOL
COMP
COMP
24 VAC HEAT
TRANSFORMER
110
24 VAC HEAT
TRANSFORMER
24 VAC COOL
TRANSFORMER
110
Figure 12
110
Figure 11
N O T E
If you have an electric system and the blower does not operate after installation, find the factory installed
yellow wire currently attached to the “Y” terminal and move it to the “A” terminal on the sub-base.
3
■ Place Base, Figure 3, over Sub-Base and attach by
tightening three captive screws.
■ Fasten loosely to wall using two mounting screws.
Place a level against the bottom of the Base, adjust
until it is level and then tighten mounting screws to
secure.
FIGURE 4
DECORATIVE
WALL PLATE
■ Find anticipator setting on old thermostat. Setting on
new thermostat should be the same. Do this by
carefully sliding the long pointer , Figure 2, over
desired number printed on the anticipator. If old
anticipator setting cannot be determined, look on gas
control on furnace, or set at at .6. During heating
season, furnace should operate about five times an
hour. If adjustments are necessary, move heat
anticipator pointer slightly and recheck.
NOTE: Set pointer to 1.2 for millivolt systems.
■ Attach front cover, Figure 1, to base.
■ Turn electricity and gas back on and set pointer on
top of thermostat to desired temperature.
■ FOR HEATING: Set slide switch to “Heat”. Set fan
switch to “Auto”.
■ FOR COOLING: Set slide switch to “Cool”. Set fan
switch to “Auto”.
■ FAN: For continuous blower operation, set switch to
“ON”. For automatic blower operation set fan switch
to “Auto”. Thermostat will then cycle the blower “on”
anf “off”.
TECHNICAL ASSISTANCE
If you have any problems installing or using this
thermostat, please carefully and thoroughly review the
instruction manual. If you require assistance, please
contact our Technical Assistance Department at
856-234-8803 during regular business hours between
8:00AM and 4:30PM Eastern Standard Time, Monday
through Friday. You can also receive technical
assistance online anytime day or night at
you answers to the most common technical questions,
and also permits you to email your questions to our
technical support staff at your convenience.
A thermostat can only control temperature near it. If
you find that it is uncomfortable some distance away
from the thermostat, change the setting in order to
compensate for this.
WARRANTY
Limited Warranty: If this unit fails because of defects
in materials or workmanship within three years of date
of original purchase, LUX Products Corporation will,
at its option, repair or replace it. This warranty does
not cover damage by accident, misuse, or failure to
follow installation instructions. Implied warranties are
limited in duration to three years from date of original
purchase. Some states do not allow limitations on
how long an implied warranty lasts, so the above
limitation may not apply to you. Please return
FIGURE 1
FRONT COVER
MOUNTING HOLE
UP
malfunctioning or defective units to the participating
wholesaler from which purchase was made, along
with proof of purchase. Please refer to "TECHNICAL
ASSISTANCE" before returning thermostat. Purchaser
assumes all risks and liability for incidental and
consequential damage resulting from installation and
use of this unit. Some states do not allow the
FIGURE 2
BASE
ANTICIPATOR
E
LONG
POINTER
.5
.3
.4
CAPTIVE
SCREW
exclusion of incidental or consequential damages, so
the above exclusion may not apply to you. This
warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
Applicable in the U.S.A. only.
CAPTIVE
SCREW
MOUNTING
HOLE
HOLES FOR WIRES
UP
vert
FIGURE 3
SUB-BASE
RECYCLING
NOTICE
This product does not contain mercury. However, this
product may replace a unit which contains mercury and
should not be disposed of in the trash. Contact your local
waste management authority for proper disposal
instructions for mercury in a sealed glass tube.
If you have any questions, please call (856) 234-8803
4
|