Marathon Sensors Inc.
Oxymit™ Transmitter
Operators Manual
Table of Contents
GENERAL DESCRIPTION............................................................................................................................ 2
SAFETY SUMMARY......................................................................................................................................3
CONNECTIONS .............................................................................................................................................. 3
GROUNDING AND SHIELDING .........................................................................................................................4
PARAMETER SELECTIONS........................................................................................................................ 4
PROCESS PARAMETERS................................................................................................................................... 4
Process Type.............................................................................................................................................5
Carbon Process Factor.............................................................................................................................5
Dew Point Process Factor........................................................................................................................ 5
Oxygen Exponent......................................................................................................................................6
TC Type.....................................................................................................................................................6
ANALOG OUTPUT CHANNELS .........................................................................................................................6
CALIBRATION...............................................................................................................................................7
PROCESS VARIABLE CALCULATIONS................................................................................................... 8
PERCENT OXYGEN.......................................................................................................................................... 8
PERCENT CARBON.......................................................................................................................................... 8
DEWPOINT...................................................................................................................................................... 8
COMMUNICATIONS..................................................................................................................................... 9
MODBUS.........................................................................................................................................................9
RTU Framing............................................................................................................................................ 9
Address Field.......................................................................................................................................... 10
Function Field.........................................................................................................................................10
Data Field...............................................................................................................................................10
Error Check Field (CRC)........................................................................................................................ 10
MEMORY MAP.............................................................................................................................................12
OPERATIONAL SPECIFICATIONS.......................................................................................................... 18
NOTE:
Please specify the following parameters when ordering a transmitter; process type, process
range (%, ppm), thermocouple type, temperature scale F/C, analog output 1 process and
scale, analog output 2 process and scale.
Typical Oxygen Transmitter Calibration
(F840030)
Calibration
Function
Measured Value or
Input
Output / Units
Cold Junction
Thermocouple
min
Room Temp
800°F (B type)
standard t/c type
°F
°F
Thermocouple
max
Millivolt
3000°F (B type)
standard t/c type
0.0 mV
°F
Millivolts
Millivolts
Millivolt
2000 mV
Analog 1 Zero
Analog 1 Span
Analog 2 Zero
Analog 2 Span
0% O2
20.9% O2
800°F +/- 5°
3000°F +/- 5°
4.0 mA +/- 0.1
20.0 mA +/- 0.1
4.0 mA +/- 0.1
20.0 mA +/- 0.1
Typical Carbon Transmitter Calibration
(F840031)
Calibration
Function
Measured Value or
Input
Output / Units
Cold Junction
Thermocouple
Min
Thermocouple
Max
Room Temp
MUST BE
SPECIFIED
MUST BE
SPECIFIED
0.0 mV
°F
°F
°F
Millivolt
Millivolt
Millivolts
Millivolts
2000 mV
Analog 1 Zero
Analog 1 Span
Analog 2 Zero
0% Carbon
2.55% Carbon
MUST BE
SPECIFIED
4.0 mA +/- 0.1
20.0 mA +/- 0.1
4.0 mA +/- 0.1
Analog 2 Span
MUST BE
SPECIFIED
20.0 mA +/- 0.1
Page 1 of 23
11/14/2006
Rev. 14
General Description
The Oxymit™ Transmitter has been designed to work as an analog or digital interface for
any zirconia based oxygen probe used to track dew point, carbon potential, or oxygen. The
transmitter connects to the temperature and millivolts outputs of an oxygen probe and can
produce analog outputs proportional to the selected process value.
The features available are:
Isolated inputs for thermocouple and probe millivolt
24 bit Sigma-Delta ADC for inputs.
Serial EEPROM to store setup and calibration values.
Two isolated self-powered 4-20mA outputs for process value and temperature.
The transmitter makes a carbon or oxygen probe an intelligent stand alone sensor. The
transmitter is located near the probe, preferably mounted in an enclosure. The transmitter
mounts onto a DIN rail and requires a 24VDC power supply. It measures the probe
temperature and millivolts. At the time of order the transmitter can be configured to
calculate percent carbon, dewpoint, or percent oxygen from these inputs. The results of
any of these calculations are made available via two 4-20mA loop outputs. Typically one
first loop is set up for the process value the second loop transmits probe temperature.
5V_A
10
9
RTX+
RTX-
5V_A
5V_B
+15V
5V_B
+24V
12
11
RS485
B
Power
Supplies
-15V
+15V
-15V
A
24V
COM
ISOLATED
ISOLATED
5V_A
5V_A
44M
+15V
D/A
22M
C
C
C
1
2
ANALOG
OUT 1
4-20mA
6
5
8
7
T/C INPUT
EEPROM
A/D
CONV.
mV INPUT
-15V
Process
Controller
ISOLATED
5V_A
+15V
D/A
D
D
D
14
13
3
4
ANALOG
OUT 2
4-20mA
EVENT INPUT
DISPLAY
CONN.
-15V
Figure 1 BLOCK DIAGRAM
Page 2 of 23
11/14/2006
Rev. 14
Safety Summary
All cautions and instructions that appear in this manual must be complied with to prevent
personnel injury or damage to the Probe Transmitter or connected equipment. The
specified limits of this equipment must not be exceeded. If these limits are exceeded or if
this instrument is used in a manner not intended by Marathon Sensors Inc., damage to this
instrument or connected devices could occur.
Do not connect this device directly to AC motors, valves, or other actuators. All AC alarm
functions must be connected through an interposing DC coil relay with a maximum coil
load of 0.5 amps DC. The Probe Transmitter is not rated to act as a safety device. It
should not be used to provide interlocking safety functions for any temperature or process
functions. Alarm capabilities are provided for probe test and input faults only and are not
to be considered or used as safety contacts in any application.
Connections
The Probe Transmitter has four removable terminal blocks grouped with four terminals
each. Each terminal is a wire clamp type with a standard slot screw. Each clamp can
accommodate AWG 24 to 12 flexible stranded wire. Maximum torque on the terminal
screws should not exceed 0.8 Nm.
The figure below shows the arrangement of the terminals.
1
2
3
4
-
+
EVT EVT
AO1
COM NO
LOWER
5
6
7
8
-
+
-
+
TC
MV
UPPER
UPPER
9 10 11 12
-
+
-
+
RS485
24VDC
LOWER
13 14 15 16
-
+
N/C N/C
AO2
Figure 2 Terminal Layout
Page 3 of 23
11/14/2006
Rev. 14
The next figure shows a schematic representation of the Probe Transmitter and typical
connections required in the field.
Figure 3 Schematic Connections
Grounding and Shielding
To minimize the pick-up of electrical noise, the low voltage DC connections and the sensor
input wiring should be routed away from high-current power cables. Where it is
impractical to do this, use shielded cables with the shield grounded at the Probe Transmitter
enclosure ground as show above.
Parameter Selections
The following tables list the parameters available in the Probe Transmitter. Default values
are also listed. The default values are loaded if a reset is force in the device. Changes to
these parameters must be specified at the time of order.
Process Parameters
The following table shows the process selections and other parameters that effect the
process value.
Page 4 of 23
11/14/2006
Rev. 14
Table 1 Process Parameters
Parameter Name
PROCESS TYPE
Selection
Default
%O2
Units or Options
Range
CARBON, DPT,
%O2, MV
CARB PROC FACT
150
0 to 1000
DEWPT PROC FACT 150
0 to 1000
0 to 31
OXYGEN EXPON
0002
POWER OF TEN
TC TYPE
B
B, C, E, J, K, N,
NNM, R, S, T
Process Type
Selecting the process type determines what type of calculation the Smart Transmitter is
going to do based on the probe millivolt and probe temperature inputs. The default process
value for the Smart Transmitter is %O2 with an exponent selection of 2. This is the
selection most often used in Boiler control and Combustion applications.
Percent Carbon and dew point are typically processes that are used in steel treating
applications. Percent Carbon is the process value most often used for the control of case
depth or the percent of carbon in a steel hardening furnace. Dew Point is used in the control
for endothermic generators.
Carbon Process Factor
The carbon process factor can be used to adjust the % carbon value. This number takes
into account a number of assumptions that the carbon value is based on. Primary among
these is the assumed level of CO in the atmosphere. See the Theory of Process Calculation
section for a complete explanation of this value.
It maybe necessary to change the apparent furnace carbon as measured by the oxygen
probe if this value is different than actual load samples, shim stocks, or gas analysis. The
basic rule of thumb is that an increase is the carbon process factor will decrease the
apparent carbon level in the furnace. The default value is 150. Typical values can very
from 50 to 400. Increase or decrease the process factor until the desired carbon level is
achieved. A process factor that is drastically different than normal may be an indication of
a failing probe, water or air leak in the furnace, or excess methane present. Refer to probe
troubleshooting guides to determine what other factors maybe effecting the carbon value.
Dew Point Process Factor
The dew point process factor is similar to the carbon process factor but is used to adjust the
dew point value if dew point is selected as the process value. This number takes into
account a number of assumptions that the dew point value is based on. Primary among
these is the assumed level of hydrogen in the atmosphere. See the Theory of Process
Calculation section for a complete explanation of this value.
Page 5 of 23
11/14/2006
Rev. 14
Oxygen Exponent
The range of oxygen is factory configured using the oxygen exponent number. Percent
oxygen is the standard setting where the oxygen exponent is set to 2 and the output range is
0.00% to 20.9%. For a part per million (ppm) range the exponent would be set to 6 and the
-6
output range of 0.00 X 10 to 99.99 X 10-6.
TC Type
The following table shows the available thermocouple types and the ranges. BOLD
indicates the typical oxygen default.
Thermocouple
Zero ºF
Zero °C
Span ºF
Span °C
type
B
C
E
J
K
800
32
32
32
32
32
32
300
300
32
425
0
0
0
0
0
0
150
150
0
3000
3000
1300
1300
2300
2300
2000
3000
3000
700
1650
1650
700
700
1260
1260
1090
1650
1650
370
N
NNM
R
S
T
The Cold Junction correction is applied to all thermocouple types.
Analog Output Channels
The analog outputs are factory configured to provide 4 to 20mA signals proportional to
selectable process values.
NOTE
The Analog Output Channels are isolated self-powered
current sources and do not require an external supply.
If a chart recorder is to be used, it should have input specifications within 4 to 20 mA. If
the recorder only responds to VDC inputs it will be necessary to add a 250 ohm dropping
resistor across its input terminals.
The ideal location of the recorder is adjacent to the instrument but it may be located
remotely if the connecting wires are properly shielded. For best results, the chart recorder
input(s) should be isolated from ground.
Page 6 of 23
11/14/2006
Rev. 14
Table 2 Analog Outputs
Parameter
Name
Oxygen
Default
Possible
Options
Possible
Ranges
OUTPUT 1
MODE
O2
O2, CARBON,
DEWPT, TEMP, LIN,
PROG
O2 = 0 – 9999
%C = 0.00 – 2.55
DP = -99.9 – 212.0
Temp = -999 – 3000
LIN = -999 – 9999
PROG = 0 – 4095
O2 = 0 – 9999
%C = 0.00 – 2.55
DP = -99.9 – 212.0
Temp = -999 – 3000
LIN = -999 – 9999
PROG = 0 – 4095
0–20.9%
4-20mA
OUTPUT 2
MODE
TEMP
O2, CARBON,
DEWPT, TEMP, LIN,
PROG
800-3000°F
4-20mA
NOTE: SEE PAGE 4 FOR TYPICAL CALIBRATION VALUES.
Calibration
The Smart Transmitter is factory calibrated. The calibration can be verified once a year or
according to customer calibration schedules. The instrument should be returned to the
factory if calibration is required.
Page 7 of 23
11/14/2006
Rev. 14
Process Variable Calculations
The transmitter has a selectable process calculation for percent carbon, percent oxygen, or
dewpoint. The following equations are used to derive these values;
Percent Oxygen
20.95
%O2 = -----------------------
e(E/0.0215*Tk)
Where: E = probe millivolts, Tk = probe temperature in degrees Kelvin.
The 20.95 is the %O2 in air.
Percent Carbon
e((E-786)/(0.043102*Tk))
%C = 5.102 ---------------------------------------------------
(29*PF + 400)+ e((E-786)/(0.043102*Tk))
Where: E = probe millivolts, Tk = probe temperature in Kelvin, and PF is the process
factor.
Dewpoint
4238.7
DP = -------------------------------------------------------------------- - 459.69
6.281216 + log((29*PF+400)+(E-1267.8)/(0.05512*Tr)
Where: E = probe millivolts, Tr = probe temperature in Rankin, PF is the process factor,
and DP is the dewpoint in Fahrenheit.
Page 8 of 23
11/14/2006
Rev. 14
Communications
The Transmitter is capable of digital communications using the Modbus protocol. This is
possible by connecting to the half duplex RS-485 terminals using a shielded twisted pair.
Modbus
The MODBUS protocol describes an industrial communications and distributed control
system (DCS) that integrates PLCs computers, terminals, and other monitoring, sensing,
and control devices. MODBUS is a Master/Slave communications protocol, whereby one
device, (the Master), controls all serial activity by selectively polling one or more slave
devices. The protocol provides for one master device and up to 247 slave devices on a RS-
485 half duplex twisted pair line. Each device is assigned an address to distinguish it from
all other connected devices. All instruments are connected in a daisy-chain configuration.
The instrument communicates with baud rate settings 1200, 2400, 4800, 9600, or 19.2K.
The default baud rate is 19.2Kbuad. The default address is 1. Changes to these values can
be made by writing to the appropriate memory register.
The Transmitter communicates in Modbus RTU (Remote Terminal Unit) protocol using 8-
bit binary data characters. Message characters are transmitted in a continuous stream. The
message stream is setup based on the following structure:
Number of bits per character:
Start bits
1
Data bits (least significant first)
Parity
8
None only (no bits for no parity)
Stop bits
1
Error Checking
CRC (Cyclical Redundancy Check)
The Transmitter recognizes three RTU commands. These are: read single I registers
(command 4), read a single H register (command 3), and preset a single H register
(command 6)
In Modbus mode, the Transmitter can be only be configured for the ‘none’ parity option.
The instrument never initiates communications and is always in receive mode unless
responding to a query.
RTU Framing
Frame synchronization can be maintained in RTU transmission mode only by simulating a
synchronous message. The instrument monitors the elapsed time between receipt of
characters. If three and one-half character times elapse without a new character or
completion of the frame, then the instrument flushes the frame and assumes that the next
Page 9 of 23
11/14/2006
Rev. 14
byte received will be an address. The follow command message structure is used, where T
is the required character delay. Response from the instrument is based on the command.
T1,T2,T3 ADDRESS FUNCTION DATA
CHECKSUM
T1,T2,T3
8-BITS
8-BITS
N X 8-BITS 16-BITS
Address Field
The address field immediately follows the beginning of the frame and consists of 8-bits.
These bits indicate the user assigned address of the slave device that is to receive the
message sent by the attached master.
Each slave must be assigned a unique address and only the addressed slave will respond to
a query that contains its address. When the slave sends a response, the slave address
informs the master which slave is communicating.
Function Field
The Function Code field tells the addressed slave what function to perform. MODBUS
function codes are specifically designed for interacting with a PLC on the MODBUS
industrial communications system. Command codes were established to manipulate PLC
registers and coils. As far as the Transmitter is concerned, they are all just memory
locations, but the response to each command is consistent with Modbus specifications.
The high order bit in this field is set by the slave device to indicate an exception condition
in the response message. If no exceptions exist, the high-order bit is maintained as zero in
the response message.
Data Field
The data field contains information needed by the slave to perform the specific function or
it contains data collected by the slave in response to a query. This information may be
values, address references, or limits. For example, the function code tells the slave to read
a holding register, and the data field is needed to indicate which register to start at and how
many to read.
Error Check Field (CRC)
This field allows the master and slave devices to check a message for errors in
transmission. Sometimes, because of electrical noise or other interference, a message may
be changed slightly while it is on its way from one device to another. The error checking
assures that the slave or master does not react to messages that have changed during
transmission. This increases the safety and the efficiency of the MODBUS system.
The error check field uses a CRC-16 check in the RTU mode.
Page 10 of 23
11/14/2006
Rev. 14
The following is an example of a function 03 call for data at memory location 03. The
value returned by the instrument is the hex value 1E.
Transmit from Host or Master
Address Cmd Reg Reg
HI LO
00 03
Count Count
HI LO
00 01
CRC CRC
HI LO
74 0A
01
03
Response from Transmitter
Address Cmd Byte Byte Data Data
Count Count HI LO
CRC CRC
HI Lo
HI
03 00
LO
02
01
00
1E
38
4C
Note that all the values are interpreted as hexadecimal values. The CRC calculation is
based on the A001 polynomial for RTU Modbus. The function 04 command structure is
similar to the 03 structure.
The following is an example of a function 06 call to change data in register 01 to 200. The
response from the instrument confirms the new value as being set.
Transmit from Host or Master
Address
01
Cmd Reg Reg Data Data
HI LO HI LO
00 01 00 C8
CRC CRC
HI LO
D9 9C
06
Response from Transmitter
Cmd Reg Reg Data Data CRC CRC
Address
01
HI
00
LO
01
HI
00
LO
C8
HI
D9
LO
9C
06
The Transmitter will respond to several error conditions. The three exception codes that
will generate a response from the instrument are:
01 – Illegal Function
02 - Illegal Data Address
03 – Illegal Data Value
04 – Slave Device Failure
The response from the Transmitter with an exception code will have the most significant
bit of the requested function set followed by the exception code and the high and low CRC
bytes.
Page 11 of 23
11/14/2006
Rev. 14
Memory Map
NOTE: Modbus refers to the hexadecimal register location. These parameters are
formatted as unsigned 16 bit integers. Any real number such as temperature can be
evaluated as a signed number, other parameters are bit mapped words that must be
evaluated as single bits are bit groups.
BLOCK 0
HEX
00
DEC
PARAMETER
Not used
DESCRIPTION
READ/WRITE
READ ONLY
READ/WRITE
0
1
LOW BYTE - TIMER CONTROL
BIT 0 – Timer Disabled (0), Timer Enabled (1)
BIT 1 – 7 SPARE
01
TIME CONTROL
SIOSET
HIGH BYTE – SIO SETUP
BITS 8 – 9 PARITY SETTING
00 = Even Parity, 7 bits, 1 Stop bit
01 = No Parity, 8 bits, 1 Stop bit
10 = Odd Parity, 7 bits, 1 Stop bit
BITS 10 – 11 RESPONSE DELAY
0 = No delay applied to response
1 = 10ms delay applied to response
2 = 20ms delay applied to response
3 = 30ms delay applied to response
BITS 12 – 14 BAUD SELECT
000 = 76.8K
001 = 38.4K
010 = 19.2K (DEFAULT)
011 = 9600
100 = 4800
101 = 2400
110 = 1200
111 = 600
BIT 15 HOST FORMAT
0 = MSI (PROP)
1 = MODBUS (DEFAULT)
02
03
04
2
3
4
TC_ZERO
TC_SPAN
LOW BYTE - TC ZERO CALIBRATION
NUMBER
READ/WRITE
READ/WRITE
READ/WRITE
HIGH BYTE – TC SPAN CALIBRATION
NUMBER
LOW BYTE – MV ZERO CALIBRATION
NUMBER
MV_ZERO
MV_SPAN
HIGH BYTE – MV SPAN CALIBRATION
NUMBER
PROCESS FACTOR FOR CARBON OR
DEWPOINT
PF
RANGE = 0 to 4095
Page 12 of 23
11/14/2006
Rev. 14
BLOCK 0
DESCRIPTION
DEFAULT = 150
HEX
05
DEC
5
PARAMETER
READ/WRITE
READ/WRITE
EVENT
LDLN
LOW BYTE – INPUT EVENT
CONFIGURATION
Bits 0 – 3
0000 = None
0001 = Auto Mode Selected
0010 = Remote Setpoint Selected
0011 = Acknowledge alarms
0100 = Timer Hold
0101 = Timer End
0110 = Timer Start
0111 = Start probe test
1000 = Process hold
Bits 4 – 7 not used.
UPPER BYTE – LOAD LINE
LOW BYTE – COLD JUNCTION TRIM
COLD JUNCTION TRIM (unsigned integer)
RANGE = –128 TO +127 WHERE
06
6
CJTRM
HADR
1 COUNT = 1 DEG (C or F) and –128 = 65408
HIGH BYTE – HOST ADDRESS
BITS 0-7
RANGE = 0 – 255
07
08
7
8
SPARE
SPARE
CONFIG0
Input Configuration
BITS 0-3 TC Input TYPE
0000 = B (DEFAULT)
0001 = E
READ/WRITE
0010 = J
0011 = K
0100 = N
0101 = R
0110 = S
0111 = T
1000 = SPARE
1001 = SPARE
1010 = SPARE
1011 = SPARE
1100 = SPARE
1101 = SPARE
1110 = SPARE
1111 = SPARE
BIT 4 = SPARE
BIT 5 0 = NO CJ APPLIED, 1 = CJ APPLIED
BIT 6 0 = °F, 1 = °C
BIT 7 0 = 60HZ FILTER
BIT 8 – 11 Millivolt Input TYPE
0000 = LINEAR (DEFAULT)
All other bit combinations are spare
BITS 12 – 15 are spare
SETUP VALUES
09
9
CONFIG2
Page 13 of 23
11/14/2006
Rev. 14
BLOCK 0
HEX
DEC
PARAMETER
DESCRIPTION
READ/WRITE
BITS 0 - 4 OXYGEN EXPONENT
RANGE = 0 to 31, where 2 = % and 6 = ppm
DEFAULT = 2
BITS 5 - 6 DISPLAY DECIMAL PLACE
where:
0 = no decimal point in display
1 = Display XXX.X
2 = Display XX.XX
3 = Display X.XXX
DEFAULT = 0
BITS 8 – 12 REDOX METAL NUMBER
RANGE = 0 – 14
DEFAULT = 0
BITS 13 – 15 SPARE
0A
10
FAULT
FAULT BIT MAP
READ ONLY
BIT 0 = Temperature Input Open
BIT 1 = MV Input Open
BIT 2 = Range of input is low
BIT 3 = Range of input is high
BIT 4 = Timer End
BIT 5 = Probe Care Fault
BITS 6 – 7 = SPARE
BIT 8 = CPU Fault
BIT 9 = Min Idle counter = 0
BIT 10 = Keyboard failure, stuck key or a key
was pressed during power up.
BIT 11 = Flash Erase Failed
BIT 12 = Flash Checksum Failed
BIT 13 = EEPROM Checksum Failed
BIT 14 = Flash/EEPROM Size Fault
BIT 15 = ADC Fault
0B
11
ASRC
ANALOG OUT SOURCES
LOW BYTE, ANALOG OUTPUT 1
BITS 0 – 3
READ/WRITE
0000 = N/A
0001 = Temperature
0010 = Linear Input A
0011 = Carbon value
0100 = Dewpoint value
0101 = Oxygen value
0110 = Redox value
0111 = Output Power
1000 = Control Output 1
1001 = Control Output 2
1010 = Linear Input B
1011 = Programmable*
*For Programmable, write required output
value into DACV1, where DACV1 = 0 is
minimum output and
DACV1 = 4096 is maximum output.
BITS 4 – 7 SPARE
Page 14 of 23
11/14/2006
Rev. 14
BLOCK 0
HEX
DEC
PARAMETER
DESCRIPTION
READ/WRITE
HIGH BYTE, ANALOG OUTPUT 2
BITS 8 – 12
0000 = N/A
0001 = Temperature
0010 = Linear Input A
0011 = Carbon value
0100 = Dewpoint value
0101 = Oxygen value
0110 = Redox value
0111 = Output Power
1000 = Control Output 1
1001 = Control Output 2
1010 = Linear Input B
1011 = Programmable*
*For Reference Number and Programmable ,
write required output value into DACV2, where
DACV2 = 0 is minimum output and
DACV2 = 4096 is maximum output.
BITS 13 – 15 SPARE
Special case: If Analog Output 1 = CONTROL
OUTPUT 1 and Analog Output 2 = CONTROL
OUTPUT 2 and the Control Mode is dual, then
Analog Output 1 is 4-20ma for 0 to +100% PO
and Analog Output 2 is 4-20ma for 0 to -100%
PO.
0C
0D
0E
0F
10
12
13
14
15
16
DAC_OFFSET_1 DAC 1 OFFSET CALIBRATION
DAC_SPAN_1 DAC 1 SPAN CALIBRATION
DAC_OFFSET_2 DAC2 OFFSET CALIBRATION
READ/WRITE
READ/WRITE
READ/WRITE
READ/WRITE
READ/WRITE
DAC_SPAN_2
AOUTOF1
DAC2 SPAN CALIBRATION
ANALOG OUTPUT 1 OFFSET
Minimum source value that correlates to
minimum Analog Output of 4 mA. The source
value is based on the selection in ASRC lower
byte
11
17
AOUTRN1
ANALOG OUTPUT 1 RANGE
READ/WRITE
Maximum source value that correlates to
maximum Analog Output of 20 mA. The
source value is based on the selection in
ASRC lower byte where
12
13
18
19
AOUTOF2
AOUTRN2
ANALOG OUTPUT 2 OFFSET
READ/WRITE
READ/WRITE
Minimum source value that correlates to
minimum Analog Output of 4 mA. The source
value is based on the selection in ASRC upper
byte
ANALOG OUTPUT 2 RANGE
Maximum source value that correlates to
maximum Analog Output of 20 mA. The
Page 15 of 23
11/14/2006
Rev. 14
BLOCK 0
HEX
DEC
PARAMETER
DESCRIPTION
READ/WRITE
source value is based on the selection in
ASRC upper byte where
14
15
16
17
20
21
22
23
SPARE
SPARE
SPARE
TEMPFIL
SPARE
SPARE
SPARE
READ/WRITE
READ/WRITE
READ/WRITE
READ/WRITE
Temperature Input Filter in seconds
Range = 0 to 3276. The higher the number
the faster the reading update.
DEFAULT = 1000
BLOCK 1
HEX
18
DEC
24
PARAMETER
MVFIL
DESCRIPTION
READ/WRITE
READ/WRITE
Millivolt Input Filter in seconds
Range = 0 to 3276. The higher the number
the faster the reading update.
DEFAULT = 1000
19
25
AZERO
LINEAR OFFSET, Y INTERCEPT LINEAR
SCALING FOR INPUT A
READ/WRITE
1A
1B
26
27
ANUM
LINEAR SPAN VALUE FOR INPUT A
READ/WRITE
READ/WRITE
BZERO
LINEAR OFFSET, Y INTERCEPT LINEAR
SCALING FOR INPUT B
1C
1D
14
15
BNUM
PROC
LINEAR SPAN VALUE FOR INPUT B
READ/WRITE
READ ONLY
This value is the calculated process value
shown as an integer. The decimal point and
exponent values are required to determine the
actual scaled value.
Range = -999 to 9999.
For example: If the process = oxygen, display
decimal point = 2, and exponent = 6, and
PROC = 1234, then the actual value and
displayed as 12.34 ppm.
1E
1F
16
17
COLDJCT
TEMP
COLD JUNCTION
READ ONLY
READ ONLY
Where 1 COUNT = 1°F (°C), RANGE = -99 TO
255°F (°C). Note this parameter is an
unsigned integer.
MEASURED TEMPERATURE
Where temperature is presented in degrees C
or F, based on the C/F setting. Note this
parameter is an unsigned integer of
temperature -2721 = 62815
Range = max / min range of selected
thermocouple.
20
21
18
19
MV
MEASURED MILLIVOLT
READ ONLY
READ/WRITE
Where this value is scaled in 0.1 mV
increments, i.e. 10001 = 1000.1.
Range = 0 to 2000 mV.
DACV1
ANALOG OUTPUT 1
0 to 4095 is 4 to 20 mA In dual mode 4mA = -
100, 12mA = 0, 20mA = +100
Page 16 of 23
11/14/2006
Rev. 14
BLOCK 1
HEX
22
DEC
20
PARAMETER
DACV2
DESCRIPTION
READ/WRITE
READ/WRITE
ANALOG OUTPUT 2
0 to 4095 is 4 to 20 ma In dual mode 4mA = -
100, 12mA = 0, 20mA = +100
SPARE
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
35
36
37
38
39
40
41
42
43
44
45
46
47
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
SPARE
Page 17 of 23
11/14/2006
Rev. 14
Operational Specifications
Power input
21.6 to 26.4 volts DC / 130mA
Thermocouple input
Thermocouple type
Zero ºF
800
32
Span ºF
3000
3000
1300
1300
2300
2300
2000
3000
3000
700
B
C
E
J
K
32
32
32
32
N
NNM
R
S
T
32
300
300
32
Bold shows default
Accuracy after linearization +/- 1 deg F
-200 to 2000 millivolts +/- 0.1 millivolt
25 Megohm
Millivolt input
Input Impedance
Cold junction compensation +/- 1 deg F
DC outputs (Isolated)
Isolation
0 to 20mA (650 max).
1000V DC/AC
Power input to signal inputs
Power input to communications
No Isolation
Calculations
Thermocouple input to Millivolt input, inputs must be differential.
Percent carbon 0 – 2.55%, no CO compensation
Dewpoint -99°F (-72.8°C) – 212 °F (100°C), no hydrogen
compensation
Percent oxygen. 0 – 20.9% (default)
CAUTION
DO NOT CONNECT ANY AC SOURCE OR LOAD TO
INSTRUMENT CONTACTS
Calibration Setups
Millivolt Null
Millivolt Span
Page 18 of 23
11/14/2006
Rev. 14
Thermocouple Null
Thermocouple Span
Cold Junction Trim
Communications port RS-485 Half Duplex Only
Protocol
Baud rates
Parity
Modbus RTU
1200, 2400, 4800, 9600, 19.2K (19.2K default)
None
Address
1 – 254 (Address 1 is default)
Housing
Material
Inflammability
Polyamide PA non-reinforced
Evaluation Class V0 (UL94)
Temperature Range -40 to 100°C
Dielectric Strength 600 kV/cm (IEC243-1)
Mounting
Snaps on to EN 50022 top hat (T) style DIN rail.
Terminals
Wire clamp screw terminals on four position removable terminal blocks.
Wire Size
AWG 24 – 12 flexible stranded, removable terminal blocks.
Max. Torque
0.8 Nm
CAUTION: DO NOT CONNECT OR DISCONNECT HOUSING PLUGS
WHILE MODULE IS POWERED OR UNDER LOAD.
Weight
10 oz
Environmental Conditions
Operating Temperature
Storage Temperature
-20 °C to 55 °C (-4 to 130 F)
-40 °C to 85 °C (-40 to 185 F)
Operating and Storage Humidity
85% max relative humidity, noncondensing, from –20
to 65°C
Certifications and Compliance (PENDING)
Safety
EN 61010-1, IEC 1010-1
Safety requirement for electrical equipment for measurement, control, and
laboratory use, Part 1
Electromagnetic Compatibility
Immunity as specified by EN 50082-2
Electrostatic discharge
Electromagnetic RF fields
EN 61000-4-2
EN 61000-403
Level 3: 8 kV air
Level 3: 10 V/m
80 MHz – 1 GHz
Page 19 of 23
11/14/2006
Rev. 14
Fast Transients
EN 61000-4-4
Level 4: 2 kV I/O
Level 3: 2 kV power
Level 3: 10 V/rms
150 KHz – 80 MHz
RF conducted interference EN 61000-4-6
Emissions as specified by EN 50081-2
RF Interference
EN 55011
Enclosure class A
Power main class A
Note: This instrument is designed for installation inside a grounded metal enclosure.
Always observe anti-static precautions when installing or servicing any electronic device.
Ground your body to discharge any static field before touching the body or terminals of any
electronic device.
This specification can change without notification.
Page 20 of 23
11/14/2006
Rev. 14
|