Master Lock Door 1651MKADA User Manual

MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
SECTION 10 51 61  
BUILT-IN COMBINATION LOCKS  
*****Since 1921, Master Lock Company has been providing padlocks and other security  
products for the construction industry. Products include built-in combination and key-  
operated locks for all types of lockers, combination padlocks for padlock hasp lockers,  
and lock management software. This product guide specification section can be used to  
specify the following built-in combination locks to be installed on metal, wire mesh, wood,  
plastic, and other types of locker:  
Combination locks for gravity/lift handle lockers (Article 2.2): Models 1630, 1631,  
1630MD, 1631MD, 1636MKADA, 1637MKADA, 1636MKMDADA, and  
1637MKMDADA.  
Combination locks with slam shut operation and dead bolt locking for single point  
rotating latch lockers (Article 2.3): Models 1690, 1690MD, 1695MKADA, and  
1695MKMDADA.  
Combination locks with slam shut operation but without dead bolt locking for  
single point horizontal latch lockers (Article 2.4): Models 1652, 1653, 1652MD,  
1653MD, 1651MKADA, 1656MKADA, 1651MKMDADA, and 1656MKMDADA.  
Combination locks for single point horizontal latch box lockers (Article 2.5):  
Models 1654, 1655, 1654MD, 1655MD, 1651MKADA, 1656MKADA,  
1651MKMDADA, and 1656MKMDADA.  
Deadbolt combination locks without slam shut operation for all locker types except  
rotating latch lockers(Article 2.6): Models 1670, 1671, 1670MD, 1671MD,  
1676MKADA, 1677MKADA, 1676MKMDADA, and 1677MKMDADA.  
The specifier will need to select appropriate products and delete non-applicable models  
and options. Refer to Master Lock product literature for descriptions and available  
options. The guide section has been written so that most editing can be accomplished by  
deleting unnecessary requirements and options. Depending on project requirements,  
some additional information will need to be added by the specifier. Options are indicated  
by [ ]. Notes to assist the specifier in selecting options and editing the specification  
guide are printed in bold and indicated with *****. For final editing, all brackets and  
notes will need to be deleted from the guide.  
For ADA accessible locks, lock operation must meet the requirements of the current  
edition of the Department of Justice (DOJ) ADA Standards for Accessible Design (ADA  
Standards) or ICC/ANSI A117.1 Accessible and Usable Buildings and Facilities.  
Verify with local jurisdiction which standard has been adopted for the project location.  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 1  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
1.2  
DEFINITIONS  
A. ADA Compliant Locks: Locks designed to meet the ADA requirements cited in the  
current edition of the DOJ ADA Standards for Accessible Design or ICC/ANSI  
A117.1 Accessible and usable Buildings and Facilities.  
B. Control Key: Key provided by lock manufacturer for use with Standard Lock  
models that will open any lock in a designated Standard Lock system.  
C. Dead bolt lock: Type of lock that once locked, the latch or bolt cannot be retracted  
or moved until the lock is properly unlocked by either dialing the correct  
combination, or turning a key.  
D. Master Key: Key provided by lock manufacturer for use with Three-Ways-to-  
Open ADA Compliant Locks that will open any Three-Ways-to-Open ADA  
compliant lock in a designated lock system.  
E. Slam Shut Operation: Indicates that the locker door will automatically lock by  
simply shutting the locker door. No further action is required.  
F. Standard Locks: Locks designed for standard use and are not designed to meet  
ADA Standards.  
G. Student Key: Is a key provided with an ADA lock that allows the user to open one  
designated ADA lock.  
H. Supervisory Key Access: A key provided by lock manufacturer that provides  
access to any lock in a lock system. Standard locks and ADA compliant locks  
cannot use the same supervisory key. Standard locks are provided with a Control  
Key and ADA compliant locks are provided with a Master Key.  
I. Three-Waysto-Open operation: Indicates that the combination lock can be  
opened by use of the correct combination, use of a master key, or use of a student  
key.  
1.3  
SUBMITTALS  
C. Provide in accordance with Section [01 33 00 - Submittal Procedures] [insert  
section number and title]:  
1. Product data for locks.  
2. Lock Installation instructions.  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS 10 51 61 - 3  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
*****Include the following paragraph if LockerManager system is being specified. *****  
3. Product data for lock management system describing functions, capacities, and  
requirements.  
D. Provide in accordance with Section 01 78 00 - Closeout Submittals:  
1. Printed control chart and text file on disc of serial numbers and lock  
combinations.  
***** For supervisory key access, a designated lock system with both standard locks and  
ADA compliant locks will require a control key for opening any standard lock and a  
master key for opening any ADA compliant lock. ADA complaint locks and standard  
locks cannot use the same supervisory key.*****  
*****For standard lock systems, Master Lock recommends a minimum of 2 control keys  
be provided per facility. Each control key opens any standard lock in a designated lock  
system. *****  
2. [2] [_____] each control keys.  
*****For ADA compliant locks, Master Lock recommends a minimum of 2 master keys  
be provided per facility. Each master key opens any ADA compliant lock in a designated  
lock system. In addition a minimum of 2 student keys should be provided for each ADA  
compliant lock in a designated lock system.*****  
3. [2] [_____] each master keys.  
4. [2] [_____] each Student keys with removable ADA compliant keyheads for  
each ADA compliant lock.  
*****Include the following paragraph if LockerManager system is being specified. *****  
5. Electronic copy of manual for lock management system.  
PART 2 - PRODUCTS  
2.1  
ACCEPTABLE MANUFACTURERS  
A. Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak  
B. Requests to use equivalent products of other manufacturers shall be submitted in  
accordance with Section 01 25 13 - Product Substitution Procedures.  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS 10 51 61 - 4  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
*****Master Lock built-in, combination locks can be factory or field installed on lockers  
manufactured by numerous manufacturers. Refer to Master Lock product literature for  
charts listing appropriate locks for various manufacturer's lockers. Select required lock  
from the following articles and delete articles for nonapplicable models. If locks are being  
specified as part of the locker specification, these articles can be inserted into the locker  
specification section. *****  
2.2  
COMBINATION LOCKS FOR LIFT HANDLE LOCKERS  
*****These eight models of built-in combination locks are provided for lift handle  
lockers.  
Standard Locks:  
Model 1630: Right-handed with plastic dial.  
Model 1631: Left-handed with plastic dial.  
Model 1630MD: Right-handed with metal dial (MD).  
Model 1631MD: Left-handed with metal dial (MD).  
ADA Compliant Locks:  
ADA compliant locks offer Three-Ways-To-Open Operation  
These locks meet the Department of Justice (DOJ) ADA Standards for Accessible  
Design (ADA Standards) and ICC/ANSI A117.1: Operation of the lock shall not  
require tight grasping, pinching, or twisting of the wrist. The force required to  
operate component shall be 5 pounds maximum.  
ADA Standards for Accessible Design; per Chapter 2, Article 2.25 Storage;  
requires providing a minimum of 5 percent ADA Accessible lockers (minimum of  
1)  
Master Lock recommends only ordering ADA compliant locks to meet the 5  
percent minimum ADA Standard, with the remainder of the locks ordered as  
standard locks.  
Model 1636MKADA: Right-handed with plastic dial.  
Model 1637MKADA: Left-handed with plastic dial.  
Model 1636MKMDADA: Right-handed with metal dial (MD).  
Model 1637MKMDADA: Left-handed with metal dial (MD).  
Edit the following to reflect required model. *****  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 5  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
A. General:  
1. Description: Built-in, combination lock with steel body for mounting in  
gravity lift handle lockers.  
2. Operation: Vertical travel locking bolt engages lift handle locker mechanism.  
This type of mechanism offers Slam Shut Operation.  
3. Mounting: Concealed in [right] [and] [left] handed door(s).  
B. Standard lock:  
1. Lock Description: 3 digit combination and 5 preset combination changes with  
5 pin tumbler lock cylinder for access using control key.  
2. Model: [1630] [1631] [1630MD] [1631MD]  
C. ADA compliant lock:  
1. Lock Description: Provide 3 digit combination and 5 preset combination  
changes with 5 pin tumbler lock cylinder which is master keyed to a master  
key and student key.  
2. Model: [1636MKADA] [1637MKADA] [1636MKMDADA]  
[1637MKMDADA]  
D. Dial:  
[1. Durable plastic dial.  
a. Color: Black]  
[2. Metal dial.  
a. Color: [Black] [Red] [Blue] [Green] [Purple]]  
[3. Provide dial with brass escutcheon plate.]  
***** Locker doors which are 11/16 to 3/4 inch thick require an extension set. Include  
the following paragraph if extension is required. *****  
E. Extension set: Provide for locker doors 11/16 to 3/4 inch thick.  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 6  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
2.3  
COMBINATION LOCKS WITH SLAM SHUT OPERATION AND DEAD BOLT  
LOCKING FOR SINGLE POINT ROTATING LATCH LOCKERS  
*****This type of lock utilizes Slam Shut Operation combined with a rotating latch that  
wraps around the latch plate making the lock more difficult to force open. Deadbolt  
locking provides a high level of security since the latch cannot be moved once the lock is  
locked.  
These four models of built-in combination locks with wrap around dead bolt latch and  
Slam Shut Operation are provided for single point rotating latch lockers  
Standard Locks:  
Model 1690: Right-handed with plastic dial.  
Model 1690MD: Right-handed with metal dial (MD).  
ADA Compliant Locks:  
ADA compliant locks offer Three-Way-To-Open Operation  
These locks meet the Department of Justice (DOJ) ADA Standards for Accessible  
Design (ADA Standards) and ICC/ANSI A117.1: Operation of the lock shall not  
require tight grasping, pinching, or twisting of the wrist. The force required to  
operate component shall be 5 pounds maximum.  
ADA Standards for Accessible Design; per Chapter 2, Article 2.25 Storage;  
requirers providing a minimum of 5 percent ADA Accessible lockers (minimum of  
1)  
Master Lock recommends only ordering ADA compliant lock models to meet the 5  
percent minimum ADA Standard, with the remainder of the locks ordered as  
standard locks.  
Model 1695MKADA: Right-handed with plastic dial.  
Model 1695MKMDADA: Right-handed with metal dial (MD).  
Edit the following to reflect required model. *****  
A. General:  
1. Description: Built-in combination lock with cast zinc body for single point  
latch lockers.  
2. Operation: Lock provides enhanced security by using rotational operating  
deadbolt latch that wraps around a stationary latch plate or post. Lock uses  
slam shut operation.  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 7  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
B. Standard lock:  
1. Lock Description: 3 digit combination and 5 preset combination changes with  
5 pin tumbler lock cylinder for access using control key.  
2. Model: [1690] [1690MD]  
C. ADA compliant lock:  
1. Lock Description: Provide 3 digit combination and 5 preset combination  
changes with 5 pin tumbler lock cylinder which is master keyed to a master  
key and student key.  
2. Model: [1695MKADA] [1695MKMDADA]  
D. Dial:  
[1. Durable plastic dial with textured lip for non-slip, one-handed, grip-and-pull  
operation.  
a. Color: Black]  
[2. Metal dial with textured lip for non-slip, one-handed, grip-and-pull operation.  
a. Color: [Black] [Red] [Blue] [Green] [Purple]]  
*****Locker doors which are 11/16 to 3/4 inch thick require an extension set. Include the  
following paragraph if extension is required. *****  
E. Extension set: Provide for locker doors 11/16 to 3/4 inch thick.  
2.4  
COMBINATION LOCKS WITH SLAM SHUT OPERATION WITHOUT DEAD  
BOLT LOCKING FOR SINGLE POINT HORIZONTAL LATCH LOCKERS  
*****These eight models of built-in combination locks with slam shut operation and  
without dead bolt locking are provided for single point latch lockers.  
Standard Locks:  
Model 1652: Right-handed with plastic dial.  
Model 1653: Left-handed with plastic dial.  
Model 1652MD: Right-handed with metal dial (MD).  
Model 1653MD: Left-handed with metal dial (MD).  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 8  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
ADA Compliant Locks:  
ADA Compliant locks offer Three-Way-To-Open Operation  
These locks meet the Department of Justice (DOJ) ADA Standards for Accessible  
Design (ADA Standards) and ICC/ANSI A117.1: Operation of the lock shall not  
require tight grasping, pinching, or twisting of the wrist. The force required to  
operate component shall be 5 pounds maximum.  
ADA Standards for Accessible Design; per Chapter 2, Article 2.25 Storage;  
requirers providing a minimum of 5 percent ADA Accessible lockers (minimum of  
1)  
Master Lock recommends only ordering ADA compliant locks to meet the 5  
percent minimum ADA Standard, with the remainder of the locks ordered as  
standard locks.  
Model 1651MKADA: Left-handed with plastic dial.  
Model 1656MKADA: Right-handed with plastic dial.  
Model 1651MKMDADA: Left-handed with metal dial (MD).  
Model 1656MKMDADA: Right-handed with metal dial (MD).  
Edit the following to reflect required model. *****  
A. General:  
1. Description: Built-in combination lock with steel body for single point  
horizontal latch lockers.  
2. Operation: Lock provides high security by using an extra long locking bolt  
without dead bolt locking. Lock uses slam shut operation.  
3. Mounting: Concealed in [right] [and] [left] handed locker door.  
B. Standard lock:  
1. Lock Description: 3 digit combination and 5 preset combination changes with  
5 pin tumbler lock cylinder for access using control key.  
2. Model: [1652] [1653] [1652MD] [1653MD]  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 9  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
C. ADA compliant lock:  
1. Lock Description: Provide 3 digit combination and 5 preset combinations  
changes with 5 pin tumbler lock cylinder which is master keyed to a master  
key and student key.  
2. Model: [1651MKADA] [1656MKADA][1651MKMDADA]  
[1656MKMDADA]  
D. Dial:  
[1. Durable plastic dial with textured lip for non-slip, one-handed, grip-and-pull  
operation.  
a. Color: Black]  
[2. Metal dial with textured lip for non-slip, one-handed, grip-and-pull operation.  
a. Color: [Black] [Red] [Blue] [Green] [Purple]]  
[3. Provide dial with brass escutcheon plate.]  
*****Locker doors which are 11/16 to 3/4 inch thick require an extension set. Include the  
following paragraph if extension is required. *****  
E. Extension set: Provide for locker doors 11/16 to 3/4 inch thick.  
2.5  
COMBINATION LOCKS FOR SINGLE POINT HORIZONTAL LATCH BOX  
LOCKERS  
*****These eight models of built-in combination locks are provided for multi-tier and  
box lockers with pull or friction latch handles.  
Standard Locks:  
Model 1654: Right-handed with plastic dial.  
Model 1655: Left-handed with plastic dial.  
Model 1654MD: Right-handed with metal dial (MD).  
Model 1655MD: Left-handed with metal dial.  
ADA Compliant Locks:  
ADA Compliant locks offer Three-Way-To-Open Operation  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 10  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
These locks meet the Department of Justice (DOJ) ADA Standards for Accessible  
Design (ADA Standards) and ICC/ANSI A117.1: Operation of the lock shall not  
require tight grasping, pinching, or twisting of the wrist. The force required to  
operate component shall be 5 pounds maximum.  
ADA Standards for Accessible Design; per Chapter 2, Article 2.25 Storage;  
requirers providing a minimum of 5 percent ADA Accessible lockers (minimum of  
1)  
Master Lock recommends only ordering ADA compliant locks to meet the 5  
percent minimum ADA Standard, with the remainder of the locks ordered as  
standard locks.  
Model 1651MKADA: Left-handed with plastic dial.  
Model 1656MKADA: Right-handed with plastic dial.  
Model 1651MKMDADA: Left-handed with metal dial (MD).  
Model 1656MKMDADA: Right-handed with metal dial (MD).  
Edit the following to reflect required model. *****  
A. General:  
1. Description: Built-in, combination lock with steel body for mounting in  
multiple-tier and box lockers with pull or friction latch handles.  
2. Operation: Horizontal operating spring bolt which retracts flush with locker  
body. Locks automatically when door is closed.  
3. Mounting: Concealed in [right] [and] [left] handed door(s).  
B. Standard lock:  
1. Lock Description: 3 digit combination and 5 preset combination changes with  
5 pin tumbler lock cylinder for access using control key.  
2. Model: [1654] [1655] [1654MD] [1655MD]  
C. ADA compliant lock:  
1. Lock Description: Provide 3 digit combination and 5 preset combination  
changes with 5 pin tumbler lock cylinder which is master keyed to a master  
key and student key.  
2. Model: [1651MKADA] [1656MKADA] [1651MKMDADA]  
[1656MKMDADA]  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 11  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
D. Dial:  
[1. Durable plastic dial with textured lip for non-slip, one-handed, grip-and-pull  
operation.  
a. Color: Black]  
[2. Metal dial with textured lip for non-slip, one-handed, grip-and-pull operation.  
a. Color: [Black] [Red] [Blue] [Green] [Purple]]  
[3. Provide dial with brass escutcheon plate.]  
*****Locker doors which are 11/16 to 3/4 inch thick require an extension set. Include the  
following paragraph if extension is required. *****  
E. Extension set: Provide for locker doors 11/16 to 3/4 inch thick.  
2.6  
HIGH SECURITY COMBINATION DEADBOLT LOCKS WITHOUT SLAM  
SHUT OPERATION  
*****Eight models of built-in combination deadbolt locks are provided for all locker  
styles including lift handle, turn handle, single point latch, and box lockers except  
rotating latch lockers. Deadbolt locking provides the highest level of security and is ideal  
for open mesh and ventilated lockers with access to back of lock.  
Standard Locks:  
Model 1670: Right-handed with plastic dial.  
Model 1671: Left-handed with plastic dial.  
Model 1670MD: Right-handed with metal dial (MD).  
Model 1671MD: Left-handed with metal dial (MD).  
ADA Compliant Locks:  
ADA Compliant locks offer Three-Way-To-Open Operation  
These locks meet the Department of Justice (DOJ) ADA Standards for Accessible  
Design (ADA Standards) and ICC/ANSI A117.1: Operation of the lock shall not  
require tight grasping, pinching, or twisting of the wrist. The force required to  
operate component shall be 5 pounds maximum.  
ADA Standards for Accessible Design; per Chapter 2, Article 2.25 Storage;  
requirers providing a minimum of 5 percent ADA Accessible lockers (minimum of  
1)  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 12  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
Master Lock recommends only ordering ADA compliant locks to meet the 5  
percent minimum ADA Standard, with the remainder of the locks ordered as  
standard locks.  
Model 1676MKADA: Right-handed with plastic dial.  
Model 1677MKADA: Left-handed with plastic dial.  
Model 1676MKMDADA: Right-handed with metal dial (MD).  
Model 1677MKMDADA: Left-handed with metal dial (MD).  
Edit the following to reflect required model. *****  
A. General:  
1. Description: Built-in, high security, combination lock with steel body for  
mounting in lift handle, turn handle, single point horizontal latch, box, and  
open mesh style lockers.  
2. Operation: Horizontal operating deadbolt which engages latch mechanism.  
Dial must be turned to relock door.  
3. Mounting: Concealed in [right] [and] [left] handed door(s).  
B. Standard lock:  
1. Lock Description: 3 digit combination and 5 preset combination changes with  
5 pin tumbler lock cylinder for access using control key.  
2. Model: [1670] [1671] [1670MD] [1671MD]  
C. ADA compliant lock:  
1. Lock Description: Provide 3 digit combination and 5 preset combination  
changes with 5 pin tumbler lock cylinder which is master keyed to a master  
key and student key.  
2. Model: [1676MKADA] [1677MKADA] [1676MKMDADA]  
[1677MKMDADA]  
D. Dial:  
[1. Durable plastic.  
a. Color: Black]  
[2. Metal dial.  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 13  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
a. Color: [Black] [Red] [Blue] [Green] [Purple]]  
[3. Provide dial with brass escutcheon plate.]  
*****Locker doors which are 11/16 to 3/4 inch thick require an extension set. Include the  
following paragraph if extension is required. *****  
E. Extension set: Provide for locker doors 11/16 to 3/4 inch thick.  
2.7  
LOCKER MANAGEMENT SYSTEM  
***** School and other facility owners must maintain some form of locker and lock  
management. Often these have been printed paper documents which are time consuming  
to update and keep current. Lock Master Company supplies locks with an accompanying  
printed control chart and a text file on disc of serial numbers and lock combinations. In  
addition, Master Lock's LockerManager software is an excellent management tool for  
tracking and managing locks, user assignments, and lock combinations. Include and  
edit this article to specify LockerManager as part of the built-in, combination lock  
package. *****  
A. Provide computerized lock and locker management system consisting of licensed  
operating software, quick start guide, and user manual; LockerManager as  
developed and published by Lock Master Company.  
B. Software: Once purchased, software is permanently activated.  
C. Support: Each license purchased shall include 1 year "Support Subscription"  
which is web based and offers resources to help user achieve most from  
LockerManager System. Support Subscription shall include questions and answers,  
training videos, update downloads, and E-mail based technical support.  
D. System shall be password protected and run on desktop personal computer (PC)  
with capability to provide mobile information via handheld computers.  
E. System functions:  
1. System shall have capacity to register and track the following with search,  
retrieve, and edit capabilities.  
a. Locker numbers and locations.  
b. Locker assignments for both individuals and groups.  
c. Lock combinations.  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 14  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
d. Portable combination padlocks.  
e. Locker repairs.  
f. Other user defined data such as schedules, emergency contact information,  
and fees.  
2. Automatically assign lockers and randomize assignments to improve traffic  
flow.  
3. Automatically assign lock combinations.  
4. Maintain complete, searchable data files.  
5. System shall be capable of expansion.  
F. System requirements:  
1. Windows 98, 98SE, ME, NT 2000, XP, or Vista.  
2. 50 MB hard drive space.  
3. Designed for SGA resolution at 1024 X 768 or higher.  
4. Pentium III Class PC (5000 MHz or higher) recommended.  
PART 3 - EXECUTION  
3.1  
INSTALLATION  
A. Locks shall be installed in accordance with lock manufacturer's instructions.  
B. Coordinate provision of built-in combination locks with fabrication of lockers to  
ensure proper, compatible strike plate is accurately installed on lockers.  
*****Include the following paragraph if locks are to be factory installed on lockers prior  
to delivery to site. *****  
C. Factory install built-in combination locks on lockers as part of [Section 10 51 13 -  
Metal Lockers] [Section 10 51 16 - Wood Lockers] [Section 10 51 26 - Plastic  
Lockers] [Section 10 51 43 - Wire Mesh Storage Lockers] [insert section number  
and title]].  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 15  
 
MASTER LOCK PRODUCT SPECIFICATIONS  
FEBRUARY 2011  
Master Lock Company, 137 West Forest Hill Avenue, P.O. Box 100367, Oak Creek, Wisconsin 53154  
*****Include the following paragraph if locks are to be field installed in either existing or  
new lockers. Typically most locks are installed in the field.*****  
D. Field install built-in combination locks in [existing lockers.] [new lockers specified  
in [Section 10 51 13 - Metal Lockers] [Section 10 51 16 - Wood Lockers]  
[Section 10 51 26 - Plastic Lockers] [Section 10 51 43 - Wire Mesh Storage  
Lockers] [insert section number and title].]  
*****Per ADA Standards and ICC/ANSI A117.1: ADA Compliant Locks shall be located  
within the allowable height and reach requirements of the ADA Standards; Chapter 3,  
article 308 Reach Ranges or ICC/ANSI A117.1; Chapter 3, article 308 Reach  
Ranges. *****  
E. ADA compliant locks shall be installed on lockers that meet the [Department of  
Justice ADA Standards for Accessible Design] [ICC/ANSI A117.1 Accessible and  
Usable Buildings and Facilities] for space allowance and reach ranges for the  
physically impaired.  
F. After installation operate each lock to ensure proper operation. Correct  
deficiencies and adjust for smooth operation. Verify combination and locker  
number are as scheduled and recorded in lock management data. Verify functional  
operation.  
G. Demonstrate to Owner's representative:  
1. Use of preset lock combinations, supervisory access, and other maintenance  
activities.  
*****Include the following paragraph if LockerManager system is being specified. *****  
2. Locker management system: Cover data input, search, retrieve, edit,  
assignment, and other system functions.  
END OF SECTION  
______________________________________________________________________________  
BUILT-IN COMBINATION LOCKS  
10 51 61 - 16  
 

LaCie Computer Drive 2big triple User Manual
Lenovo Computer Drive 40Y8699 User Manual
Lenovo Laptop B470E User Manual
LG Electronics Cell Phone U400 User Manual
Life Fitness Stepper Machine LS9100 User Manual
Lincoln Electric Welding System IM10056 User Manual
Linear Switch HDMI SW 2X4M User Manual
Linksys Cordless Telephone SPA 900 SERIES User Manual
Maytag Range W10239463A User Manual
Metabo Kitchen Utensil 091 101 6397 User Manual