High Performance
32-Bit PCI Bus
Ethernet Adapter
With support for BNC and
RJ45 connectors
NX-32PCI
USER'S GUIDE
Part#MAN108Rev. 1.0
NX32PCI/D
2.1 Unpacking Your Network Adapter
Your package should contain the following items:
Adapter Card
Driver disk
BNC T-connector
User's Guide
The back plate of the card has
the following features (See Fig-
ure 2-1):
Figure 2-1
• 2 network cable connectors:
RJ45 Connector
for
10BASE-T networks
BNC Connector
for
10BASE-2 networks
RJ-45
• 2 LED indicators with the fol-
lowing functions:
LINK (green) - Link Status.
The card is success-
fully connected to a
10Base-Tnetwork.Not
used with BNC con-
nections.
BNC
ACT (green) - Network ac-
tivity. Indicates when
the card is receiving
network data.
2.2 Hardware Installation
Installation of this adapter card requires opening
and manipulating your PC. Exercise caution at all
times when working with AC powered and static-
sensitive equipment. Turn off and unplug your PC
before installation. Discharge any static electricity
from your body by touching any metal surface.
Note: If you are also installing the optional boot
ROM, refer to Section 2.2.1 for detailed ROM
installation instructions before beginning adapter
installation.
2
1. Turn off your computer and all peripherals.
2. Make a note of the power cord and other
cables connected to your computer and
disconnect them.
3. Remove your computer’s cover (refer to
your computer’s owner manual).
4. Select an available PCI expansion slot, and
then remove the slot cover.
5. Touch the computer chassis before remov-
ing the adapter from its anti-static bag. This
will discharge any static electricity from your
body.
6. Carefully install the adapter by firmly press-
ing the card into the slot you have chosen,
applying even pressure until the adapter is
completely seated in the slot.
7. Fasten the retaining bracket with the screw
from the slot cover. Make sure the adapter
is properly aligned. Store the slot cover for
future use.
8. Replace the computer cover and reconnect
the power cord and all cables.
9. Attach the network cable to your adapter.
Proceed to Section 2.3.
2.2.1 Boot ROM Installation (optional)
An empty ROM socket is provided on the adapter
to accept an optional Remote Boot ROM (available
from your dealer). The Boot ROM allows the PC to
load the Operating System over the network for
diskless applications.
1. Insert the Boot ROM into the socket. Make
sure that the notch on the ROM matches the
one on the socket (refer to Figure 2-2).
2. Be certain to enable your adapter's boot
ROM by setting the Boot ROM Size param-
eter to “16 Kilobytes” when running the
SETUP.EXE program after the card has
been installed (Refer to Section 2.4.2). Re-
3
Figure 2-2 Boot ROM alignment
Align ROM
and socket
notches
turn to Section 2.2 to continue installa-
tion.
2.3 PCI Adapter Configuration
The steps used to configure your adapter depend
on whether your computer system supports the
Plug and Play (PnP) 1.0a specification. You most
likely have a Plug and Play 1.0a compliant system
if it was purchased after June 1994 or if the BIOS
is dated after June 1994.
If your system is PnP compliant, either in BIOS or
if you are running Windows 95, go to Section 2.3.1.
If you have a non-Plug and Play system, proceed
to Section 2.3.2 for detailed information on how to
configure your adapter.
2.3.1 Configuration in Plug and Play systems
On systems with Plug and Play motherboards the
cardwillbeconfiguredautomaticallybythesystem's
BIOS during boot-up. The BIOS automatically
assigns the I/O base address and IRQ to the card
for proper operation. Continue to Section 2.4.
2.3.2 Configuration in Non-Plug and Play Sys-
tems
Early generation PCI bus PCs require that the PCI
adapter card be configured using the BIOS setup
program. Setup options include: A) enabling the
specific slot in which the adapter is installed, B) the
selection of Bus Master mode, and C) selection of
4
the IRQ.
The procedures to perform PCI card setup on early
generation PCI bus PCs and the related terms to
describe each procedure vary depending on which
BIOSyourcomputeruses.Refertoyourcomputer's
manual for specific information on configuring PCI
slots. As an example, generally an early generation
Phoenix BIOS has a “Device Select” field where
you should input the number of the slot (printed on
the PC motherboard next to the PCI slot) into which
the card was inserted. The field that reads “Enable
Device” should be set to “Enabled.” In addition, set
the “Enable Master” field to “Enabled”. Set the IRQ
for the adapter's slot to one which is unused by
other devices in the system.
Your BIOS may also require setting the IRQ trig-
gering method. There are three types of settings to
chose from:
•
•
•
Level/Auto - This is usually the default.
Choosing this option leaves the assigned
IRQ free for other use if the installed card
does not use it.
Level/Forced - If you are not able to get the
PCI card to work properly, choose this op-
tion. This will assign the specified IRQ per-
manently to the card.
Edge/Auto - Some PCI boards support this
option. Do not use it.
Continue with the installation by proceeding to
Section 2.4.
2.4 Running the Set Up Utility
After the adapter is configured, run the setup/
diagnostic utility SETUP.EXE found on the driver
diskette to: A) view the adapter configuration, B)
set optional configuration parameters, and C) per-
form adapter diagnostics. Do not run SETUP.EXE
with network drivers loaded. Refer to the file
README.TXT in the root directory for detailed
5
information.
To run SETUP.EXE, insert the driver diskette into
a disk drive.
From the DOS prompt, change to that drive by
typing A: (or B:) and pressing Enter.
Type \SETUP at the DOS prompt and press Enter.
This will start the program.
2.4.1 View Current Configuration
Select View Current Configuration to see the
current adapter settings. This option will show the
settings for:
•
•
•
•
•
•
Ethernet Address
Medium Type
Full Duplex
I/O Base
Interrupt
Boot ROM Size
2.4.2 Set Up New Configuration
The Set Up New Configuration option allows you
to change settings on the adapter. Your PC's BIOS
should have automatically allocated the neces-
sary I/O base address, interrupt, and Boot ROM
address (if needed) to the adapter. SETUP will not
allow you to change any resources which are
allocated by the BIOS. It does allow the user to
change the following settings:
•
•
•
Medium Type
Full-Duplex Function
Boot ROM Size
Medium Type has four options: A) 10 BASE-T,
TP/CX Auto-Detect for 10Base-T (RJ-45) or
10Base-2(BNC)networks(automaticallydetected),
B) 10 BASE-T Link Test Disabled for twisted pair
networks, C) 10 BASE-5 for 10Base-5 (this selec-
tion cannot be used with this card), and D) 10
BASE-2 for coaxial networks.
6
The Full-Duplex Function should be enabled only
if the server you are attached to and all intercon-
necting devices (e.g. switching hubs) support this
mode.
Boot ROM Size should only be set if a Boot ROM
is present on the card. Enabling this setting allows
remote booting from the server. Refer to Section
2.2.1 for more information on installing the Boot
ROM.
2.4.3 Testing The Adapter
Setup provides the following testing options under
Run Diagnostics:
• Run EEPROM Test
• Run Diagnostic On Board
• Run Diagnostic On Network
Note: Do not run SETUP with network drivers
loaded.
The Run EEPROM Test option performs read/
write tests on the adapter's on-board EEPROM
registers and reports the results.
The Run Diagnostic On Board option runs sev-
eral tests and the results are indicated by either
PASS or FAIL counts. Make sure that the network
cable is attached (and properly terminated if using
a BNC connection) to the adapter when using this
option. If any test has a fail count, press the
spacebar for help on the reason for the failure and
possible solutions.
The following tests are performed in the Run
Diagnostic On Board option:
1. Board Reset: Confirms the adapter will
reset.
2. I/O Registers: Checks I/O accessibility.
3. Loop back Test: Checks the adapter's con-
troller.
4. CableConnection:Testsforacorrectcable
connection.
7
5. RAM Test: Checks on-board RAM.
The Run Diagnostics on Network option allows
the user to test the network cable connection
between two cards. One card is setup as a Re-
sponder and a second card is setup as an Initia-
tor. The Initiator and Responder will exchange
packets and display the number of transmit and
receive packets that have passed or failed. Note:
A Responder can only recognize one Initiator at a
time.
2.5 Configuration Files
Two options are available in SETUP.EXE to easily
configure many cards to the same settings. Note:
The Save Configuration to File and Load Con-
figuration from File only involve the param-
eters in the Setup New Configuration option of
the main menu. These setup parameters can be
saved to disk to be later loaded on other machines
to configure other cards.
Section Three - Driver Installation
The network operating system (i.e. Novell, Win-
dows 95, Windows NT, LAN Manager, etc.) that
you are using requires a driver to access the
network adapter card. Drivers for popular network
operating systems are included on the installation
disketteinseparatesubdirectories.RunHELP.EXE
to view information on each network driver.
Most network operating systems provide a setup/
installation program to configure your computer for
use on the network. These programs copy the
appropriate driver directly from the adapter's driver
diskette. Section 3.1 gives an example of this using
Windows 95.
Important Note:
If you are using an upper memory manager, your
8
32-bit (PCI) adapter can only function with 32-bit
versions of the EMM386.EXE memory manager
program (version 4.49 or later). You can verify its
version by entering EMM386 at the DOS prompt.
Do not specify the “highscan” option with the
EMM386.EXE statement in your CONFIG.SYS file
or your system will hang.
If you run MEMMAKER and select Custom Setup,
do not specify “Aggressively scan upper memory,”
or it will automatically insert the HIGHSCAN flag
into the EMM386 command line. This parameter
cannot be removed once it is installed. Doing so will
cause the extended memory manager to malfunc-
tion.
3.1 Windows 95 Driver Installation
Note: Windows 95 identifies most add-on cards
based on the chipset used. The MaxTech Ethernet
adapters use the Realtek Ethernet chipset and will
be identified as such.
When Windows 95 starts for the first time after card
installation,itdetectstheadapterasa“PCIEthernet
Controller” card. If Windows displays the New
Hardware Found dialog box, proceed to Section
3.1.1. If Windows displays the Update Device
Driver Wizard, proceed to Section 3.1.2.
3.1.1 Windows 95 Release 4.00.950
Under New Hardware Found, when asked to
“Select which driver you want to install for your new
hardware,” click on “Driver from disk provided by
hardware manufacturer.” Click “OK.”
The Install From Disk dialog box now instructs
you to “Insert the manufacturer's installation disk
into the drive selected, and then click OK.” Insert
the adapter's driver diskette and type A:\WIN95 (or
B:\WIN95 if inserted in drive B) in the “Copy
manufacturer's files from:” box. Click “OK.”
The Select Device dialog box presents the selec-
9
tionfortheadapter. Click“OK”toinstalltheadapter.
Windows 95 may request its own installation disks
for some files. Insert the Windows 95 disks as
required. When all necessary files are copied, the
adapter is configured. Restart Windows 95 as
prompted.
3.1.2 Windows 95 Release 4.00.950 B
When Windows 95 starts for the first time after card
installation, it detects the card and displays the
Update Device Driver Wizard.
Insert the driver disk into the disk drive and click
“Next.” Windows will search for the driver on the
driver disk. If you need to enter the location of the
driver, click “Other Location,” type A:\WIN95 (or
B:\WIN95) in the entry box and click “OK”. Click
“Finish.”
Windows 95 may request its own installation disks
or CD for some files. Insert the Windows 95 disks
or CD as required. When all necessary files are
copied, the adapter is configured. Restart Win-
dows 95 as prompted.
Section Four - Using the Remote
Boot ROM
A Remote Boot ROM allows the PC to load the
operating system over the network on diskless
workstations. Be certain that the Boot ROM has
been properly installed (Refer to Section 2.2.1) and
enabled on both PnP and Legacy systems. Refer to
section 2.4.2 for instructions.
Once the Boot ROM is installed and enabled, follow
the Remote Boot Workstation installation proce-
duregiveninyournetworkoperatingsystemmanual
(i.e. create a Boot Image on the server for Novell
networks, or start remote booting services on LAN
Manager networks, etc.).
10
Section Five - Troubleshooting
This section describes some of the common prob-
lems you may encounter while using your network
adapter. When troubleshooting, you should make
sure that the network you are connected to is
functioning. If you suspect that the adapter is
malfunctioning, replace it with another adapter
which is known to function properly. Also try the
adapter in another computer. This can indicate
whether the adapter or computer causes the prob-
lem. If you can not resolve your difficulty after
reading the following information, contact your
dealer or vendor for assistance.
Most adapter failure after installation is caused by:
A) PC IRQ Line conflict, or B) Cable problems.
5.1 IRQ Conflict
Make sure that the IRQ used by the adapter is
notalreadyinusebyanotherdeviceinyourPC.
Vary the settings on your network adapter by
running the BIOS setup program to eliminate the
conflict. Running the adapter diagnostics will also
help to detect configuration conflicts.
5.2 Cable Problems
A) Observe the green Link Status LED if you are
using a 10Base-T network. Turn on the computer.
Connect the network cable and observe the green
LINK LED. If the LED is ON, then the system is
connected. Otherwise check for a proper RJ-45
connection.
B)Makesurethecoaxialcableisproperlytermi-
nated if you are using a 10Base-2 network. Each
end of a coaxial segment must be properly termi-
nated with a 50-ohm terminator. You may use a
simple ohm meter to determine if the cable is
functioning properly. Disconnect all nodes on the
network and measure the resistance of the termi-
11
nators. If the terminators do not measure 50 ohms
+/- 1%, replace the terminator. Measure the coaxial
cable with a 50-ohm terminator attached to one
end. The total resistance of the cable plus the
terminator should be no more than a few ohms
more than the terminator alone.
Section Six - Cable Information
The MaxTech NX-32PCI network adapters support
bothCoaxandUTPcableschemesusedinEthernet
networks.
10Base-T networks use unshielded twisted-pair
cable and 8-pin RJ-45 modular connectors. Use
22-26 AWG, 2- or 4-pair, 100 ohm/ft. UTP Cat-
egory 3 or better cable. The cable must use solid
copper conductors and UL codes CM, CMR, and
CMP are required. The computer on the network is
connected via a star topology (i.e. each node is
connected to a HUB, not to each other). Maximum
cable length is 328' (100 m).
10Base-2 networks use a single conductor coaxial
cable and BNC connectors. Use only RG-58A/U or
RG-58C/U coaxial cable. Each network node is
connected to the coaxial cable via a T-connector
(included). The minimum distance between T-
connectors is 1.6' (0.5m). The T-connector must be
plugged directly into the network adapter (no cable
is allowed between the T-connector and the
adapter). No more than 30 connections are al-
lowed per segment and the maximum segment
length is 607' (185 m). The cable must be termi-
nated at each end by one 50-ohm terminator.
Section Seven - Specifications
NetworkStandard:
EthernetInterface:
I/Oaddress:
IEEE802.3
32-bit PCI Local bus
Automaticallydeterminedbyconfigu-
rationspace
12
IRQ:
BIOS/OperatingSystemselectable.
Interrupt:
RAM Buffer:
INT A
16 KB
PowerConsumption: 2.5 W
Temperature:
0 to 50 degrees C (Operating)
-20 to +70 degrees C (Storage)
10%to80%(Non-condensing,oper-
ating)
Humidity:
5% to 90% (Non-condensing, stor-
age)
Dimensions:
Certification:
4.73" x 3.15"
FCC Part 15 Class B
Drivers: Artisoft Lantastic, Novell NetWare 3.x, 4.x, FTP
PC/TCP, LAN Manager V2.x, Windows For Workgroups,
Windows95,WindowsNTV3.1&3.5,DECPathworksV4.x
& 5.0, SUN PC-NFS, Banyan VINES, SCO UNIX
Section Eight - Technical Support
Intheunlikelyeventyouexperiencedifficultyintheuseofthe
product, or if it does not operate as described, we suggest
you: (1) consult the Troubleshooting section of this guide
and (2) consult with your dealer.
IfyouhavenotreferredtotheTroubleshootingsection,
there is a good chance the solution to your problem is
there.Ifyoustillcannotsolvetheproblem,calltheMaxTech
Service Center at (562) 921-4438 between 9:00 a.m. and
6:00 p.m. (PST Monday through Friday). If the nature of
yourquestionisrelatedtothenetworkoperatingsystem
thatyouareusing,refertoitsmanual.CallingtheService
Centerwithoutcompleteandaccurateinformationconcerning
the NATURE OF THE PROBLEM will be both time-
consumingandfrustratingforyou.
You may also reach us through our electronic BBS. Any
revisionsorupdatesofavailabledriverswillbepostedonthe
BBS.Thisserviceisavailable24hoursadayat:(562)921-
7180.
Section Nine - Notices
9.1 Five Year Limited Warranty
MaxTech warrants to the original buyer of this product
againstdefectsinmaterialandworkmanshipforfiveyears
13
from the date of purchase. During the warranty period,
MaxTechwillrepair(oratitsoption,replace)theproductthat
proves to be defective, provided the product has not been
abused,misused,modified,orrepairedbyanunauthorized
center.
In the event the product requires service, follow the proce-
dureoutlinedinSectionEight-TechnicalSupport.When
youareinstructedbytheTechnicalSupportRepresentative
toreturntheproducttoMaxTechforrepair,youwillbegiven
anRMA(ReturnMerchandiseAuthorization)number.You
must have an RMA Number to return the product for
service.Usethefollowingproceduretoreturntheproductto
MaxTech:
1. Returntheproductinitsoriginalpackageandpack-
ing(ifpossible),andputitinasturdycorrugatedbox.
2. Be sure to include your name, address, day-time
telephone number, RMA number, and a brief de-
scription of the problem (also enclose a check for
out-of-warrantyrepair).EncloseyourcheckorPostal
Money Order for $7.50 to cover the cost of return
shipping/handling. Please do not send cash or
stamps.
4. After wrapping the package securely for shipping,
print your name, return address and the RMA #
clearly on the outside of your package.
5. Ship the unit prepaid via UPS or the U.S. Postal
ServiceTotheaddressprovidedbythetechnician
when you call. We recommend that the unit be
insured.
This warranty is valid for products sold in North America
only. Contactyourlocalauthorizeddistributorordealerfor
thewarrantyofferedinotherareas.
All warranty services must be performed by Authorized
ServiceCenters.Therearenouserserviceablepartsinside
theunit.Donotremoveanycomponentsorattempttoservice
theunitbyanyunauthorizedservicecenter.Thiswarrantyis
voidediftheproducthasbeenabused,misused,modified,
orrepairedbyanunauthorizedservicecenter.
9.2 FCC Class B Statement
Thisequipmenthasbeentestedandfoundtocomplywiththe
limits for a Class B digital device, pursuant to Part 15 of the
FCCRules.Theselimitsaredesignedtoprovidereasonable
protectionagainstharmfulinterferenceinaresidentialinstal-
14
lation.Thisequipmentgenerates,usesandcanradiateradio
frequencyenergy,andifnotinstalledandusedinaccordance
withtheinstructions,maycauseharmfulinterferencetoradio
communications.However,thereisnoguaranteethatinterfer-
encewillnotoccurinaparticularinstallation.Ifthisequipment
doescauseharmfulinterferencetoradioortelevisionrecep-
tion, which can be determined by turning the equipment off
andon,theuserisencouragedtotrytocorrecttheinterference
byoneormoreofthefollowingmeasures:
• Reorientorrelocatethereceivingantenna
• Increasetheseparationbetweentheequipmentandthe
receiver
• Connecttheequipmentintoanoutletonacircuitdifferent
from that to which the receiver is connected
• Consultthedealeroranexperiencedradio/TVtechnician
forhelp
Notice:1)Shieldedcables,ifany,mustbeusedinorderto
complywiththeemissionlimits.2)Anychangeormodifica-
tionnotexpresslyapprovedbytheGranteeoftheequipment
authorizationcouldvoidtheuser’sauthoritytooperatethe
equipment.
9.3 Disclaimer, Copyright, And Other Notices
Theinformationcontainedinthismanualhasbeenvalidated
at the time of this manual's production. The manufacturer
reservestherighttomakeanychangesandimprovements
in the product described in this manual at any time and
withoutnotice.Consequentlythemanufacturerassumesno
liability for damages incurred directly or indirectly from
errors,omissionsordiscrepanciesbetweentheproductand
themanual.
Allregisteredtrademarksarethepropertyoftheirrespective
owners.
Copyright © 1997 MaxTech. All rights reserved. No repro-
duction of this document in any form is allowed without
writtenpermissionfromMaxTech.
FirstEdition
GZ/DR - Version 1.0
15
|