Moxa Technologies Switch Uport 1200 1400 1600 User Manual

When the Found New Hardware wizard finishes installing UPort, use  
the operating system’s Device Manager to check and/or modify the port  
settings. The new COM port will be listed under Ports (COM & LPT).  
2. Click Next to install the driver in the indicated folder.  
1200/1400/1600  
USB-to-Serial Hub  
Quick Installation Guide  
2. Package Checklist  
Before installing the UPort, verify that the package contains the following  
items:  
Third Edition, January 2007  
UPort 1200/1400/1600 USB-to-serial hub  
1 USB cable  
Document and Software CD-ROM  
UPort 1200/1400/1600 Quick Installation Guide  
Power adaptor (for UPort 1250I/1450I/1600-8) or power cord (for  
UPort 1600-16)  
1. Overview  
UPort is the brand name of MOXA’s USB-to-serial product line, which  
provides a wide range of products and solutions to extend Windows COM  
ports using the PC’s USB port. Important features of UPort products  
include support for hi-speed (480 Mbps) USB 2.0, Moxa CPU, Moxa  
UART, the ability to assign COM port numbers, magnet accessories, and  
mini female DB9 to terminal block. These features make the UPort  
products easy to use and maintain.  
Notify your sales representative if any of the above items are missing or  
damaged.  
3. Installing the UPort 1200/1400/1600 Driver  
The UPort 1200/1400/1600 line of USB-to-serial hubs includes the  
following models:  
3. Click Install to proceed with the installation.  
1. Run the Setup program located on the UPort 1200/1400/1600  
Document and Software CD-ROM. Click Next to start installing the  
driver.  
UPort 1250  
2-port RS-232/422/485 USB-to-serial hub  
UPort 1250I  
2-port RS-232/422/485 USB-to-serial hub w/  
isolation protection  
UPort 1410  
UPort 1450  
UPort 1450I  
4-port RS-232 USB-to-serial hub  
4-port RS-232/422/485 USB-to-serial hub  
4-port RS-232/422/485 USB-to-serial hub w/  
isolation protection  
UPort 1610-8  
8-port RS-232 USB-to-serial hub  
UPort 1650-8  
8-port RS-232/422/485 USB-to-serial hub  
UPort 1610-16 16-port RS-232 USB-to-serial hub  
UPort 1650-16 16-port RS-232/422/485 USB-to-serial hub  
Before connecting the UPort USB-to-serial hubs to your computer’s USB  
port, we recommend installing the UPort driver first. To do this, follow  
the installation procedure described in Section 3.  
The installation procedure described in Section 3 was done on a PC  
running Windows 2000 (x86). Windows XP and 2003 (32-bit and 64-bit)  
driver installations are the same. UPort can be connected to any upstream  
type A USB port that is on the PC host or on an upstream hub. UPort is  
hot pluggable, and therefore there is no need to power down your  
computer prior to installation.  
After installing the driver, connect the UPort to an upstream host or hub.  
The Found New Hardware wizard will locate the appropriate drivers  
automatically. Once the drivers are found, various windows will pop up  
as UPort’s serial port is being installed.  
P/N:1802014000200  
— 1 —  
— 2 —  
— 3 —  
 

MTD Automobile Electronics APS 620 User Manual
Multiquip Portable Generator GA 6HE User Manual
Nextar MP3 Player N10W 400 User Manual
NordicTrack Home Gym NTBE15060 User Manual
Nortel Networks Network Card Cartridge User Manual
Onkyo Stereo System HT S6100 User Manual
Panasonic Air Conditioner CS PC12JKF User Manual
Panasonic Cordless Telephone KX TGP550 User Manual
Panasonic Indoor Furnishings ET PKF100S User Manual
Patton electronic Mouse 1195 4E1 User Manual