S I M P L Y
A M A Z I N G ®
No. 1 for Easy, Powerful Cleaning
Since 1963
USER’S GUIDE
XL2 6 0 6 HH
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
BEFORE OPERATING CLEANER,
READ ALL INSTRUCTIONS IN
THIS MANUAL CAREFULLY.
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic
precautions should always be followed,
including the following:
Table of Contents
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
Maintenance and Customer Service,
Accessories, Important Safety Instructions . . . . . . . . . . . . . . . page
3
4
Guarantee, Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . page
WARNING
To reduce the risk of fire,
electric shock, or injury:
Parts List, Assembly, Operating Instructions,
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page
5
6
To Replace Filter Dust Bag, How to Replace a Worn Belt,
To Adjust or Replace Brush, Using an Oreck Fresh Air® Tab,
Stuffing or Blockage, Warning . . . . . . . . . . . . . . . . . . . . . . . . . page
• Do not leave appliance unattended when plugged in.
Unplug from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not operate the unit while in the upright and locked
position.
• Do not let the unit run while in any one stationary position
for any period of time. Keep the unit moving while in
operation.
Maintenance and Customer Service
Your Oreck vacuum cleaner is a product of precise engineering. The
motor bearings are permanently lubricated and should not be oiled. If
you require additional information or have problems with your Oreck
appliance, or to order new bags or spare parts, you may call ORECK
customer service at:
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
Phone: 03-9540-0700
• Use only as described in this manual. Use only
manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not
working as it should, has been dropped, damaged, left
outdoors, or dropped into water, return it to a service
center or call customer service at: 03-9540-0700
• Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges or corners.
Keep cord away from heated surfaces.
Or write to:
Godfreys
2103 Dandenong Road
CLAYTON, VICTORIA 3168
Attention: Oreck Customer Service
Please specify the model number and serial/code number which can be
found on the data plate on the back of the vacuum.
• Do not run appliance over cord.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair and anything
that may reduce air flow.
• Keep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.
• Do not use to pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
• Do not use without filter bag assembly in place.
• Turn off all controls before unplugging.
Accessories
ITEM
1.
PART #
Dust Bag, 8 Pack, Saniseal®
Hypo-Allergenic
CCPK8DW
CCPK8
Dust Bag, 8 Pack, Regular
Belts, 3 Pack
Oreck Fresh Air® Tabs
2.
3.
0300604
AIRTABS
ALL SPARE/SERVICE ARE PROVIDED DIRECTLY BY GODFREYS TO
PROVIDE THE MOST EFFICIENT SERVICE POSSIBLE.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids,
such as gasoline or lighter fluid, or use in areas where
they may be present.
• Do not use appliance in an enclosed space where
flammable, explosive or toxic vapors are given off by oil
base paint, paint thinner, some mothproofing substances,
or in an area where flammable dust is present.
• Do not pick up toxic material such as chlorine bleach,
drain cleaner, gasoline, etc. with this appliance.
• Use caution when vacuuming over area rug edges and
fringe.
SAVE THESE INSTRUCTIONS
Household Use Only
3
Troubleshooting Guide
WARNING: Unplug cord from electrical
outlet before servicing.
Guarantee
SAVE SERVICE CALLS...CHECK THESE FIRST:
• Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
• Is anything clogging the revolving brush, lower tube, intake opening,
fan housing or connector assembly opening?
ORECK XL
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
No. 1 for Easy, Powerful Cleaning since 1963
Hy p o - Alle rg e n ic Cle a n e r Plu s
Co m p a ct Ba rre l Cle a n e r
• Does the brush turn freely? Are hair, string or rug fibers wound around
the brush?
This guarantee is given in addition to the rights you have
against the manufacturer or supplier from whom you purchased
this product. This product is guaranteed for three (3) years
against faulty material or workmanship. The casing is
guaranteed for ten (10) years. This limited warranty covers the
revolving roller brush for one (1) year for residentail use only. If
a part is found to be defective from the date of purchase
agreement, we will replace or, at our option, repair that part
without any charges for material or labor; ONLY if the appliance
has been used for those purposes in accordance with the
instructions provided with each appliance and has not been
connected to an unsuitable electricity supply or subjected to
misuse, neglect, damage, stuffing or blockage, or modified or
repaired by service stations not authorized by ORECK or a
representative of ORECK.
PROBLEM
CLEANER
POSSIBLE SOURCE
AREAS TO CHECK
Not plugged in
properly.
Be sure cleaner is
firmly plugged into
wall outlet.
WILL NOT RUN
No electricity in wall
outlet.
Check electrical
source–fuse or
circuit breaker.
CLEANER
DOES NOT PICK UP
Filter bag is full.
Replace filter bag.
See “To Replace
Paper Filter Dust Bag.”
Nozzle or intake
pivot clogged.
Clear obstruction.
Replace belt.
Please note that proof of purchase is required.
When writing or telephoning, please give the following information:
A. Your name, address and telephone number.
B. Model number and name of product.
C. Date of purchase.
Belt is broken or
stretched.
Brush is worn.
See “To Adjust or
Replace Brush.”
D. Fault if known.
Lower tube clogged.
Clear obstruction.
Change bag.
You will be advised what action to take by our customer service
staff. This guarantee will be invalidated if spares other than the
manufacturer’s are used.
Bag pores are
clogged with fine
dust.
Impeller fan is
broken.
Return to Service
Center for repair.
GODFREYS.
2103 Dandenong Road
Revolving brush is
not even at both
ends.
Check brush roll end
cards. Make sure
words “OLD” or
“NEW” match at
each end.
CLAYTON, VICTORIA 3168
FREE CALL
03-9540-0700
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
CALL CUSTOMER SERVICE HOT LINE
0 3 - 9 5 4 0 - 0 7 0 0
Whenever calling, please be sure to have your model and serial
number from data plate.
4
Operating Recommendations
Parts List
This new ORECK XL High-Speed Upright is one of the finest, fastest,
and strongest units in its class. You’ll love the way it cleans, gets under
things, and it’s SO lightweight and easy to use.
To assist you in identifying components of your vacuum, the parts have
been numbered as follows:
The following are a few simple suggestions regarding its operation:
1. When inserting a new disposable paper filter dust bag—FIRST
PUFF OUT and OPEN THE BAG.
1
2
3
4
5
6
7
8
9
Handle Tube, upper
Tube, lower
10
2. When the disposable filter dust bag is full, REPLACE IT.
11
Power head
9
3. If at any time the machine does not pick up properly or makes an
unusual noise, STOP OPERATION and service.
Outer bag
1
12
Paper filter dust bag
Power cord
4. Although your upright will pick up pins, paper clips, and other
small objects, it is recommended that these be removed from the
floor before you vacuum. Failure to do so may result in permanent
damage to the motor suction fan and its housing.
Retaining spring
Bag tension bar
Zip fastener
16
5
5. WARNING: Do not use your vacuum cleaner on damp or wet
surfaces. This will cause damage to the vacuum cleaner and is
dangerous to the user. Damage caused by use on wet or damp
surfaces is not covered under warranty.
13
4
10 On/off switch
11 Cord dump
2
6
6. REPLACE THE BELT EVERY 6 MONTHS.
12 Plastic loop / cable clamp
13 Connector assembly
14 Fan housing
7. Change the disposable filter dust bag at least once a month—
even if it is not full! The collected dust in the dust bag can cause
odor, attract moisture, and can affect the efficiency of the cleaner.
15 Cord assembly
7
14
8. DO NOT run the vacuum cleaner over the cord. The revolving
brush could damage the cord.
8
15
16 Cord strain relief assembly
9. Use caution when vacuuming over area rug edges and fringe.
3
General Information
Assembly
The performance of your new cleaner greatly depends upon care and
maintenance. The instructions in this manual will guide you in
performing basic care and maintenance. To obtain the most satisfying
years of service read the instructions and keep them handy for future
reference.
fig. 1 Before assembling appliance, remove two screws from connector
assembly. Remove cardboard insert by pulling upward.
fig. 2 With ON/OFF switch facing the front of the unit, slide upper
handle section over matching section of the connector assembly.
Hold tab of cord strain relief flush with TOP hole in connector
assembly. Insert screw through hole in tab of cord strain relief
and firmly tighten to connector assembly. Insert remaining screw
in botom hole of connector assembly and tighten firmly.
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role in the
efficiency of your ORECK vacuum cleaner. The purpose of the paper
bag is to trap dirt, but at the same time it must be porous enough to
allow air to pass through. If the paper bag becomes clogged, no air can
pass through the cleaner and cleaning cannot take place, regardless of
the cleaner’s power.
NOTE: The power cord comes installed in the cord strain relief.
Should the power cord come loose, simply pinch the power cord
together and slide approximately 1 - 2 inches through hole in
cord strain relief. Carefully slide power cord over clamp on the
the cord strain relief and pull excess until the power cord is
tightly rested under clamp.
To keep your cleaner operating at maximum efficiency, change the dust
bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE
DUST BAG.
Be sure the disposable paper filter dust bag is installed properly.
fig. 3 Attach cord to cord clip by pressing cord above and below clip
All paper dust bags are not the same. Your ORECK disposable
dust bags have been designed to be used with the ORECK cleaner.
Using bags other than genuine ORECK TYPE CC disposable bags
will affect the cleaning ability of your cleaner and could cause
damage to it.
ensuring the cord is fully rested in clip.
Operating Instructions
The Belt
Make sure disposable paper filter dust bag is in place. DO NOT operate
the cleaner without a paper filter dust bag. Plug the power cord into an
electrical outlet and press the ON (l) - OFF(O) switch on Helping Hand®
when ready to operate.
The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to
stop completely or slow down. See instructions in the manual for
replacing belt.
Up-Position Lock
fig. 4 Place foot on power head and lean handle back gently to release
lock for vacuum use. Return handle to the full upright position to
engage lock.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts. Belts
other than ORECK belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to
the motor and brush bearings. Using belts other than ORECK belts
will void the warranty.
NOTE: Do not operate the unit while in the upright and locked position.
Do not let the unit run while in any one stationary position for any period
of time. Keep the unit moving while in operation.
Lubrication
For Easy Power Cord Storage
fig. 5 Wrap power cord around cord dump on Helping Hand® handle
The vacuum cleaner motor bearings are factory lubricated and sealed.
Further lubrication is not required.
and cord hook on connector.
fig. 6 To release cord, twist cord dump located on Helping Hand®
handle 1/2 turn. Slide cord off handle.
5
General Cleaner Care
To Adjust or Replace Brush
At least once a month, check for and
remove excessive lint, string or hair
from revolving brush.
WARNING: Unplug cord from electrical
outlet before servicing.
Wipe the outside of the cleaner with
a damp cloth. Also clean the
connector deflector assembly area,
base of cleaner and fan housing
area. If there is dust in the outer bag,
vacuum it or shake it out.
fig. 17 To determine if the brush is worn, place a firm straight edge
across the nozzle opening. If brush bristles do not extend
beyond baseplate, brush should be adjusted.
fig. 18 Remove the baseplate by removing 5 screws.
fig. 19 Remove the belt and brush roll from the housing.
fig. 20 Rotate both bearing assemblies at ends of brush roll to show
A little preventative maintenance will
keep your cleaner looking new and
will ensure continued cleaning effec-
tiveness.
"OLD" and replace in the holding channels in the housing.
NOTE: The bearing assembly setting marked "OLD" has a smooth
side. The one marked "NEW" has notches. When rotating bearings,
make sure both bearing assembly settings are the same and face up
when replacing the brush roll.
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor
Surfaces and Polished Floor Finishes
fig. 17 Reassemble the belt and the baseplate and check bristle height
Use floor and floor finish manufacturer’s recommended methods of
cleaning. The metal strip on the base of the cleaner could be damaged
if used on concrete or abrasive surfaces, and, therefore, cause damage
to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished
floor finishes. The roller brush may also scuff very soft finishes. Do not
operate the unit while in the upright and locked position. Do not let the
unit run while in any one stationary position for any period of time. Keep
the unit moving while in operation.
above baseplate at each end of brush.
If a previous adjustment has already been made and bristle height does
not extend above baseplate, a new brush assembly should be ordered.
IMPORTANT: Unless the brush is worn as indicated above, both
bearings must be in the “NEW” position. When rotating, both
bearings must be in the “OLD” position. Unmatched settings will
cause damage to your machine.
Celoc® Hypo-Allergenic Filter System
The Celoc SMMS outer bag of your vacuum cleaner is high filtration
medical material designed to filter the smallest of dust particles. It is
important that the inside of the outer bag be cleaned. Vacuum the inside
of the outer bag or hand wash, turned inside out, with warm water, and
air dry. For best results, the Celoc SMMS outer bag should be replaced
once a year. The Celoc layered disposable inner dust bag must be
replaced once a month even if it is not full. Change it more often if it is
used in extremely dirty areas. Increase the cleaning power of your
vacuum by changing the bag often.
Using An Oreck Fresh Air® Tab
fig. 21 Your ORECK XL vacuum cleaner has a special ORECK
FRESH AIR® tab pocket. This pocket is located inside the outer
bag in the area where the disposable paper filter bag attaches
to the intake tube. Insert tablet in pocket if desired.
Stuffing or Blockage
IMPORTANT: On plush and new carpets, stuffing may occur inside the
the intake tube and the lower tube assembly. This is due to excessive
fuzz and loose cuttings in the carpet. Stuffing could occur for the first
few cleanings until all the loose material is removed. Due to the high
efficiency of the cleaner, many older carpets will cause stuffing when
the cleaner is first used on them. If your vacuum cleaner does not pick
up properly, or makes unusual noise and the outer bag does not fluff up
or balloon open, follow these steps:
To Replace Filter Dust Bag
WARNING: Unplug cord from electrical
outlet before servicing.
BAG REMOVAL:
fig. 7 Unzip outer bag completely.
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 8 Pull bag cardboard collar to release bag dock door from
connector. Bag dock door will hinge downward.
fig. 9 Gently pull bag cardboard collar upward out of the bag dock.
fig. 22 Check for blockage at the mouth of the intake opening. If there
is blockage, remove it with long-nose pliers, a screwdriver or
coat hanger. If you can not reach the blockage, remove
baseplate (fig. 23).
Dust seal will close automatically.
BAG INSTALLATION:
fig. 10 Slide the cardboard collar completely onto bag dock door.
fig. 24 If the blockage is not at the base, remove lower tube. Unhook
fig. 11 Firmly push bag dock door with both thumbs on indication point
retainer spring, releasing bottom of bag.
until snap is heard.
fig. 25 Twist lower collar counterclockwise to slide up. Pull tube out of
base.
How to Replace a Worn Belt
fig. 26 Check for blockage. If blockage is in the tube, remove with a
coat hanger.
WARNING: Unplug cord from electrical
outlet before servicing.
fig. 27 If tube is not blocked, look into fan housing. Remove debris
with long-nose pliers, a screwdriver or coat hanger.
fig. 12 Remove the replacement belt from the storage channel.
fig. 25 To reassemble, check O-ring on tube, and replace if damaged.
Vacuum will not operate properly without the tube O-ring. Slide
O-ring to approximately 2" from base of tube. Replace tube by
first lining up slot at base of tube with inner tab inside fan
housing. Then reinsert tube and push down until the tube is
seated. Make sure O-ring is in place against fan housing
opening. Replace and tighten collar until collar locking tabs are
locked in place.
fig. 13 Remove the door by removing the hold down screw located on
side of power head.
fig. 14 Slide the door forward by prying open with a screwdriver or
coin.
fig. 15 Remove the belt from the motor drive shaft and brush roll
pulley.
fig. 16 Loop the new belt over the motor drive shaft. Place the
opposite end of the belt on the brush pulley. Rotate the brush
roll three (3) complete revolutions to ensure that no part of the
belt is overhanging the end of the motor drive shaft.
fig. 28 Make sure collar is not cross threaded on housing. Reattach
bag spring (fig. 24).
fig. 29 Many times blockage occurs due to a full dust bag causing dirt
to back down the air flow system. When that happens, the
blockage will be at the top of the system, starting in the area
where the dust bag connects to the connector assembly.
fig. 14 Replace the door by sliding it into the groove at the bottom of
the housing.
fig. 13 Replace the hold down screw and tighten.
NOTE: If the above actions do not correct the problem, contact an
Oreck authorized service center or call the customer service center.
03-9540-0700
6
Warning
This Oreck is very powerful and may pick up items which your old
cleaner did not. Please be careful to clean the floor of larger items
which your old cleaner passed over such as pencils and small toys.
These items can cause a blockage in your machine.
7
No. 1 for Easy, Powerful Cleaning
Since 1963
75386-08 REV A
10/06 ECN# R-8360
©2006 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used
under the authority of Oreck Holdings, LLC.
8
|