Philips Portable CD Player AX2401 55 User Manual

Portable CD Player  
AX2400  
AX2401  
AX2420  
1
user manual  
1
2
manuel d’utilisation  
manual del usario  
Manual do usuário  
3
4
9
8
7
5
6
@
0
!
Meet Philips at the Internet  
QUICK START  
MISE EN SERVICE RAPIDE  
1
OPEN  
3
5
CD  
4
HOLD OFF  
6
PLAY 2;  
7 VOL  
AX2400, AX2401, AX2420  
CLASS 1  
LASER PRODUCT  
!!!  
 
GENERAL INFORMATION / CD PLAY  
CD PLAY / FEATURES  
In-car use (connections supplied or optionally available)  
Playback information  
If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded  
properly, NF dISCis displayed, indicating that the CD has not been  
finalized. In that case, use FINALIZE on your CD recorder to complete the  
recording.  
When playing a CD-Rewritable (CD-RW), please note that it takes 3–15  
seconds after pressing 2; for sound reproduction to start.  
Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) car voltage  
converter (4.5 V DC, positive pole to the centre pin) and the AY 3501 car adapter  
cassette. Any other product may damage the set.  
1
Put the set on a horizontal, vibration-free and  
stable surface. Make sure it is in a safe place,  
where the set is neither a danger nor an  
obstacle to the driver and the passengers.  
12 V DC  
Playback will stop if you open the CD lid.  
While the CD is read, 1--:--flashes in the display.  
2
Plug the voltage converter into the  
cigarette lighter socket (only for 12 V car  
battery, negative grounding), then connect  
the wired end with 4.5V DC input socket on the  
set.  
4,5 V DC  
Volume and bass  
Volume adjustment  
Adjust the volume by using VOLUME +/-  
on the cd player.  
3
4
If necessary, clean the cigarette lighter socket  
to obtain a good electrical contact.  
Turn down the volume and connect the cassette adapter plug to  
p/LINE OUT on the set.  
5
6
7
Carefully insert the cassette adapter into the car radios cassette compartment.  
Make sure the cord does not hinder your driving.  
Decease the volume on the set, if necessary. Start playback on the set and  
adjust the sound with the car radio controls.  
Bass adjustment  
Press DBB to switch the bass enhancement on or  
off  
Always remove the voltage converter from the cigarette lighter socket  
when the set is not in use.  
DBB  
y
appears if the bass enhancement is  
Note: If your car radio has a LINE IN socket , it is better to use it for the  
car radio connection instead of the cassette adapter. Connect the signal  
lead to this LINE IN socket and to p/LINE OUT on the set.  
activated.  
DBB  
Playing a CD  
Selecting a track and searching  
Selecting a track during playback  
This CD-player can play all kinds of Audio Discs such  
as CD-Recordables and CD-Rewritables. Do not try to  
play a CD-ROM, CDi, VCD, DVD or computer CD.  
Briefly press or § once or several times to skip to  
the current, previous or next track.  
yPlayback continues with the selected track, and  
the track’s number is displayed.  
1
2
Push the OPEN ç slider to open the player.  
Selecting a track when playback is stopped  
Insert an audio CD, printed side up, by pressing the  
CD onto the hub.  
1
Briefly press or § once or several times to select  
the desired track. The track number is displayed.  
3
4
Close the player by pressing the lid down.  
2
Press 2; to start CD play.  
yPlayback starts with the selected track.  
Press 2; to switch the player on and start playback.  
yThe current track number and elapsed playing  
time are displayed.  
Searching for a passage during playback  
1
Keep or § pressed to find a particular passage in  
a backward or forward direction.  
ySearching starts while playback continues at low  
volume. After 2 seconds the search speeds up.  
You can pause playback by pressing 2;.  
yThe time at which playback was paused starts  
flashing.  
You can continue playback by pressing 2; again.  
2
Release the button when you reach the desired passage.  
yPlayback continues from this position.  
5
Press 9 to stop playback.  
yThe total number of tracks and the total playing  
time of the CD are displayed.  
Notes: – If the player is in SCAN mode (see MODE chapter), searching is not  
possible.  
– In shuffle, shuffle repeat all or repeat mode (see MODE chapter), or  
while playing a program, searching is only possible within the  
particular track.  
6
Press 9 again to switch the player off.  
To remove the CD, hold it by its edge and press the  
hub gently while lifting the CD.  
Note: If there is no activity, the set will automatically  
switch off after a while to save energy.  
 
FEATURES  
FEATURES / TROUBLESHOOTING  
Programming track numbers  
RESUME and HOLD  
You can interrupt playback and continue (even after an  
extended period of time) from the position where  
playback stopped (RESUME) and you can lock all buttons  
of the set so that no action will be executed (HOLD). Use  
the RESUME–HOLD–OFF slider for these functions.  
You can store up to 30 tracks to play in a program.  
A single track may be stored more than once in the  
program.  
1
While playback is stopped, select a track with  
or §.  
RESUME – continuing from where you have stopped  
2
Press PROG to store the track.  
1
Switch the slider to RESUME during playback to acti-  
vate RESUME.  
yprogram lights up; the track number  
programmed and Pwith the total number of stored  
tracks are displayed.  
yRESUME is shown.  
2
3
Press 9 whenever you want to stop playback.  
3
4
Select and store all desired tracks in this way.  
Press 2; whenever you want to resume playback.  
yRESUME is shown and playback continues from  
where you have stopped.  
Press 2; to start playback of your selected tracks.  
yprogram is shown and playback starts.  
To deactivate RESUME, switch the slider to OFF.  
yRESUME goes off.  
You can review the program by pressing PROG for more than 2 seconds.  
yThe display shows all the stored tracks in sequence.  
HOLD – locking all buttons  
Notes: – If you press PROG and there is no track  
selected, SELis displayed.  
You can lock the buttons of the set by switching the slider to HOLD. Now, when a  
key is pressed, no action will be executed. This is of use, for example, when  
transporting the player in a bag. With HOLD activated, you can avoid accidental  
activation of other functions.  
– If you try to store more than 30 tracks,  
FULLis displayed.  
Clearing the program  
1
Switch the slider to HOLD to activate HOLD.  
yAll buttons are locked. HoLdis shown when  
you press any button. If the set is switched off,  
HOLD will be shown only when 2; is pressed.  
hold  
While playback is stopped, press 9 to clear program.  
yCLRis displayed once, program goes off, and  
the program is cleared.  
2
To deactivate HOLD, switch the slider to OFF.  
Note: The program will also be cleared if the power  
supply is interrupted, or if the CD-player lid is  
opened, or if the set switches off automatically.  
Note: If you deactivate HOLD by switching the slider to  
RESUME, you will be activating the RESUME function.  
Selecting different playing possibilities-MODE  
Troubleshooting  
It is possible to play tracks in random order, to repeat a  
single track or the entire CD, and to play the first few  
seconds of each track.  
WARNING: Under no circumstances should you try to repair the set yourself as  
this will invalidate the warranty. If a fault occurs, first check the points listed,  
before taking the unit for repair. If you are unable to solve a problem by following  
these hints, consult your dealer or service center.  
1
Press MODE during playback as often as required in  
order to activate one of the following ‘modes’. The  
active mode is shown in the display.  
ySHUFFLE : All tracks of the CD are played in  
random order until all of them have been played  
once.  
The CD player has no power, or playback does not start  
Check that your batteries are not dead or empty, that they are inserted  
correctly, that the contact pins are clean.  
Your adapter connection may be loose. Connect it securely.  
For in-car use, check that the car ignition is on. Also check players batteries.  
ySHUFFLE REPEAT ALL : All tracks of the CD  
are played repeatedly in random order.  
The indication NO dISCis displayed  
yREPEAT : The current track is played repeatedly.  
yREPEAT ALL : The entire CD is played repeatedly.  
Check that the CD is clean and correctly inserted (label-side upward).  
If your lens has steamed up, wait a few minutes for this to clear.  
y
SCAN: The first 10 seconds of each of the  
remaining tracks are played in sequence.  
The indication NF dISCis displayed  
CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.  
2
Playback starts in the chosen mode after 2 seconds.  
The indication HOLD is on and/or there is no reaction to controls  
To return to normal playback, press MODE repeatedly  
until the display shows no active modes.  
If HOLD is activated, then deactivate it.  
Electrostatic discharge. Disconnect power or remove batteries for a few seconds.  
The CD skips tracks  
ESP  
The CD is damaged or dirty. Replace or clean the CD.  
With a conventional portable CD-player you might have experienced that the  
music stopped e.g. when you were jogging. The Electronic Skip Protection  
prevents loss of sound caused by light vibrations and shocks. Continuous playback  
is ensured. However ESP does not prevent playback interruptions during vigorous  
running. It also does not protect the unit against any damage caused by dropping!  
RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on.  
No sound or bad sound quality.  
PAUSE might be active. Press 2;.  
Loose, wrong or dirty connections. Check and clean connections.  
Volume might not be appropriately adjusted. Adjust the volume.  
Strong magnetic fields. Check players position and connections. Also keep  
away from active mobile phones.  
In this set ESP is default ON. It is possible to set ESP off.  
Press MODE/ESP for more than 3 seconds.  
y ESP disappears.  
Press MODE/ESP again for more than 3 seconds.  
y ESP is displayed.  
For in-car use, check that the cassette adapter is inserted correctly, that the car  
cassette players playback direction is correct (press autoreverse to change),  
and that the cigarette lighter jack is clean. Allow time for temperature change.  
ESP on ESP off ESP on  
 
Philips 3 years Manufacturers Warranty for Australia only  
AUSTRALIA-  
d) Product failures caused by misuse, neglect, accidental breakage, transit damage,  
These warranty conditions are valid for the following consumer electronics  
products: Colour Televisions, Video Cassette Recorders, CD Players and  
Recorders, DVD Players and Recorders, Audio Systems and Portable Audio.  
The benefits given to the purchaser by this warranty are in addition to all other  
rights and remedies which the purchaser has in respect of the product under the  
Trade Practices Act or other Commonwealth or State Law.  
inexpert repairs or modification by un-authorised persons, external fires, lightning  
strikes, floods, vermin infestation or liquid spillage.  
e) Cleaning of video or audio heads.  
f) Inadequate receiving antennae.  
g) Replacement of worn or used batteries or other consumables.  
h) Consumer products used in commercial applications (This warranty is limited to 3  
months only).  
Philips Consumer Electronics warrants its products to the purchaser as follows and subject  
to the stated conditions.  
i) Second hand products.  
3
YEARS free Repair Service  
The conditions contained in this warranty card replace and override the provision of the  
Philips World-Wide Guarantee for products purchased in Australia and used in Australia.  
Philips Authorised Service Centres  
Colour Televisions, CD Players and Recorders, DVD Players and Recorders and Audio Systems.  
3
YEARS free Replacement – at your Retailer  
All Portable Audio products and all Video Cassette recorders (VCR’s) only.  
Service is provided through 200 accredited Authorised Service Centres throughout  
Australia. For direct contact with your nearest recommended Authorised Service Centre  
in major cities:  
Conditions of Repair Warranty  
1. All claims for warranty service should be made to your nearest Philips Authorised  
Service Centre. Reasonable evidence of date of purchase must be provided.  
2. This warranty extends only to defects in material or workmanship occurring under nor-  
mal use of the product when operated in accordance with the instructions.  
3. This warranty applies for original purchase only. It is not transferable if sold.  
4. Home service within the normal service area of one of our Authorised Service Centres  
will only be provided for television receivers with screen size 48 cm and above. All other  
products are to be taken or sent to the workshop of your nearest Authorised Service  
Centre (at Consumer’s expense).  
Adelaide  
Launceston  
Brisbane  
Melbourne  
Canberra  
Geelong  
Perth  
Sydney  
Hobart  
Newcastle  
Gold Coast  
Wollongong  
or to find the location of your nearest recommended Authorised Service Centre outside  
the above cities please call our National Service telephone number:  
1300 361 392  
Please record the following information for your records and keep in a safe place.  
Model number:....................................................  
Serial number:....................................................  
Date of purchase:....................................................  
Retailer:....................................................  
5. This Manufacturers Warranty is limited to 3 months for above listed Consumer  
Electronics products if used in commercial applications.  
6. Philips may, at its discretion choose to replace rather than repair any product covered by  
this warranty.  
7. This Manufacturers Warranty is neither transferable nor valid in countries other than  
Australia.  
This warranty does not cover:  
We recommend you retain your purchase receipt to assist in any warranty claim.  
a)Mileage or travelling time, pickup or delivery, installations and cost of insurance.  
b)Mileage or travel outside the normal service area covered by selected Authorised  
Service Centre.  
Philips Consumer Electronics  
a division of Philips Electronics Australia Limited  
ABN 24 008 445 743,  
c)Service costs arising from failure to correctly adjust the controls of the product  
or to observe the instructions, or inspections that reveal that the product is in  
normal working order.  
Level 2, 65 Epping Road NORTH RYDE NSW 2113  
st  
3 year Warranty valid for all new products purchased after 1 July 2002  
-
Guarantee and Service for New Zealand  
NEW ZEALAND  
Thank-you for purchasing this quality Philips product.  
How to claim  
Philips New Zealand Ltd guarantees this product against defective components  
and faulty workmanship for a period of 12 months. Any defect in materials or  
workmanship occurring within 12 months from the date of purchase subject to  
the following conditions will be rectified free of charge by the retailer from  
whom this product was purchased.  
Should your Philips product fail within the guarantee period, please return it to  
the retailer from whom it was purchased. In most cases the retailer will be able  
to satisfactorily repair or replace the product.  
However, should the retailer not be able to conclude the matter satisfactorily, or if  
you have other difficulties claiming under this guarantee, please contact  
Conditions  
The Guarantee Controller  
Philips New Zealand Ltd.  
1. The product must have been purchased in New Zealand. As proof of purchase,  
retain the original sales docket indicating the date of purchase.  
4
P.O. Box 41.021  
Auckland  
2. The guarantee applies only to faults caused by defective components, or faulty  
workmanship on the part of the manufacturer.  
3. The guarantee does not cover failures caused by misuse, neglect, normal wear  
and tear, accidental breakage, use on the incorrect voltage, use contrary to  
operating instructions, or unauthorised modification to the product or repair by  
an unauthorised technician.  
3
(09) 84 94 160  
fax 3 (09) 84 97 858  
4. Reasonable evidence (in the form of a sales docket) must be supplied to indi-  
cate that the product was purchased no more than 12 months prior to the date  
of your claim.  
5. In the event of a failure, Philips shall be under no liability for any injury, or any  
loss or damage caused to property or products other than the product under  
guarantee.  
This guarantee does not prejudice your rights under common law and statute,  
and is in addition to the normal responsibilities of the retailer and Philips.  
 

Philips Car Stereo System MCM1006 User Manual
Philips Indoor Furnishings 3000K User Manual
Philips Speaker SPA2300 User Manual
Philips Switch SWS2283W User Manual
Philips Universal Remote ph601s User Manual
Photogenic Professional Lighting Battery Charger AKB 1 User Manual
Pioneer DVD Recorder DVR K06 User Manual
Poulan Lawn Mower PR625Y22RHP User Manual
Presto Cooktop 01241 User Manual
ProForm Treadmill PFTL69712 User Manual