Python Automobile Alarm Model 902 User Guide

Model 902  
Owner’s Guide  
 
CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM  
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER  
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.  
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY  
AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY  
CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE  
AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.  
DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV-  
ER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,  
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF  
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY  
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER  
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-  
TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on  
how long an implied warranty will last or the exclusion or limitation of incidental or con-  
sequential damages. This warranty gives you specific legal rights and you may also have  
other rights that vary from State to State.  
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your autho-  
rized Directed dealer for details of the plan or call Directed Customer Service at 1-800-  
876-0800. Directed security systems, including this unit, are deterrents against possible  
theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft  
of the automobile, its parts or contents; and hereby expressly disclaims any liability what-  
soever, including without limitation, liability for theft, damage and/or vandalism.  
Directed does not and has not authorized any person or entity to create for it any other  
obligation, promise, duty or obligation in connection with this security system.  
Make sure you have all of the following information from your dealer:  
A clear copy of the sales receipt, showing the following:  
Date of purchase  
Your full name and address  
Authorized dealer's company name and address  
Type of alarm installed  
Year, make, model and color of the automobile  
Automobile license number  
Vehicle identification number  
All security options installed on automobile  
Installation receipts  
© 2006 directed electronics  
ii  
 
table of contents  
limited lifetime consumer warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i  
2-way LCD remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . 1  
LCD screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
standard remote configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
what is included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
iimportant information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
replacement remote controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
2-way LCD remote control functions . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . 7  
standard configurations (1-way and 2-way remote controls) . . . . . . . . . . . . . . . . 7  
standard LCD icon configurations (2-way only) . . . . . . . . . . . . . . . . . . . . . . . . . 9  
remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
system signal paging features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
out of range notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
programming LCD remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
To enter programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Beeps/Vibration On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Illumination On/Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Page notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
To exit programming mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
using yoour system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
active arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
passive arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
disarming without a transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
dome light control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
valet mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
nuisance prevention® circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
auxiliary outputs (options) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
shock sensor adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
To enter shock sensor adjustment mode:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Adjusting the Shock Sensor Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Exit Shock Sensor Adjustment Mode:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Reset Shock Sensor to Default Setting: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
© 2006 directed electronics  
iii  
 
diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . 35  
arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
interpreting zone diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
owner recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . 41  
installation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
vehicle recovery system (vrs®) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
arming the vrs® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
vrs® triggered sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
disarming the vrs® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
security & conveniennce expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50  
glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53  
quick reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
© 2006 directed electronics  
iv  
 
2-way LCD remote control  
6
3
4
5
2
1
7
1.  
2.  
3.  
4.  
5.  
6.  
7.  
Auxiliary Channel Button  
Arm Button  
LCD Screen (see LCD Screen)  
Disarm Button  
Panic Button  
Battery Compartment  
Program Button  
© 2006 directed electronics  
1
 
LCD screen  
1 2 3 4  
5
6
7
23  
22  
21  
8
9
10  
11  
12  
20  
19  
18  
17  
13  
16  
15  
14  
1. Transmit  
2. Out of range  
3. Receive  
13. Battery level indicator  
14. Remote start (option)  
15. Field disturbance sensor *  
16. Shock sensor setting  
4. Auxiliaries  
5. Garage door (519H2 option) 17. Vibrator  
®
6. Warn Away  
7. Alarm  
18. Ignition  
19. Hood  
8. Ultrasonic sensor *  
9. Tilt sensor *  
10. Trunk  
20. Vehicle number  
21. Door  
22. Arm  
11. Glass breakage sensor *  
12. Shock sensor  
23. Disarm  
* Optional sensors. Additional parts and labor required  
© 2006 directed electronics  
2
 
standard remote configuration  
Lock–Arm/Panic On/Panic Off  
controls the  
controls the  
function.  
Unlock–Disarm/Panic Off  
function.  
Silent Mode™  
Auxiliary Output (2)  
controls  
and an  
.
Panic On/Off  
or  
controls the  
function (hold for 2-  
seconds).  
Auxiliary Output (3)  
.
and  
or  
pressed together control an  
Auxiliary  
pressed together control an  
and  
Output (4)  
.
Auxiliary Output (5)  
.
and  
pressed together control an  
Auxiliary  
pressed together control an  
and  
or  
Output (6)  
.
© 2006 directed electronics  
3
 
P
(located on back of the remote) selects the vehicle to control  
and also provides user selection of LCD remote response .  
what is included  
Control module  
1 four-button 2-way LCD transmitter  
1 four-button transmitter  
note: On both remotes the panic button is the same color.  
Wire harnesses  
Dual diode harness  
The 514N six-tone programmable siren  
In-vehicle status LED indicator light  
A push-button Valet switch  
Your warranty registration  
®
Failsafe Starter Kill ready circuitry  
(may require additional labor)  
548T transceiver/antenna  
important information  
Congratulations on the purchase of your state-of-the-art vehicle  
security system. This system has been designed to provide years  
of trouble-free operation. Due to the complexity of this system,  
it must be installed by an authorized dealer only. Installation of  
© 2006 directed electronics  
4
 
this product by anyone other than an authorized dealer voids the  
warranty. All dealers are provided with preprinted dealer certifi-  
cates to verify that they are authorized.  
This owner’s guide should help you to get the most out of your  
system. Please take the time to read it prior to using the system.  
system maintenance  
This system needs no specific maintenance beyond remote  
control battery replacement. The 2-way remote is powered by a  
1.5V AAA battery. The 1-way remote is powered by a pair of 3V,  
CR2016 batteries.  
Battery Level Indicator (2-way remote)  
The Battery Level indicator has four level indicators that serve as  
a visual indication of battery charge. When the battery reaches a  
low charge level that requires replacement, the remote control  
will generate a single notification chirp, and the Battery Level  
indicator will flash continuously.  
FULL  
Battery Replacement (2-way remote)  
EMPTY  
REPLACE  
Gently pull the end of the battery door away from the top of the  
remote control then slide the door up to expose the battery and  
remove the expired battery. Place the new battery into the remote  
control observing the correct polarity. When power is returned  
the remote control will display all icons in the LCD and generate  
© 2006 directed electronics  
5
 
all beeper tones once. Press any button on the remote to termi-  
nate the beeper tone review.  
your warranty  
Your warranty registration must be returned and the bar code  
serial number must not be removed. If the warranty registration  
is not returned, you do not have a warranty. It is also necessary  
to keep your proof of purchase, which reflects that the product  
was installed by an authorized dealer. Make sure that you receive  
the warranty registration from your dealer.  
fcc/id notice  
This device complies with Part 15 of FCC rules. Operation is  
subject to the following two conditions: (1) This device may not  
cause harmful interference, and (2) This device must accept any  
interference received, including interference that may cause  
undesirable operation.  
Changes or modifications not expressly approved by the party  
responsible for compliance could void the user's authority to  
operate this device.  
3201 Series  
© 2006 directed electronics  
6
 
replacement remote controls  
You can purchase replacement remote controls from your  
Authorized Dealer or on-line at the following web site:  
Once you receive your new remote control, please refer to  
instructions included on the remote packaging.  
2-way LCD remote control functions  
The LCD remote control buttons are used to send commands to  
the system. The descriptions below reflect the standard configu-  
ration for this system. The buttons can be custom configured for  
the user’s specific needs by the installer. Also, the user can  
configure the LCD remote for certain responses (see  
Programming LCD Remote section).  
standard configurations (1-way and 2-way remote  
controls)  
Button  
The arming function is controlled by pressing this button for  
one second.  
Button  
The disarming function is controlled by pressing this button for  
one second.  
© 2006 directed electronics  
7
 
Button  
Silent Mode™ and an optional auxiliary function are controlled  
by pressing this button. (Silent Mode™ works by pressing this  
button for less than one second before arming or disarming. An  
optional auxiliary function, such as trunk release, can be  
controlled by pressing this button for 1.5 seconds.)  
The auxiliary output controls __________________________.  
or  
Button  
The panic feature is controlled by pressing this button for  
approximately two seconds.  
and  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
buttons simultaneously.  
The auxiliary output controls_________________________.  
or  
and  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
buttons simultaneously.  
The auxiliary output controls_________________________.  
and  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
© 2006 directed electronics  
8
 
buttons simultaneously.  
The auxiliary output controls_________________________.  
and  
or  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
buttons simultaneously.  
The auxiliary output controls_________________________.  
Program Button (on rear of 2-way LCD remote only)  
Use this button to select the vehicle to control from the remote.  
Also use this button to configure response characteristics from  
the LCD remote (see Programming 2-Way Remote).  
standard LCD icon configurations (2-way only)  
Icon  
The transmit icon will be displayed while the remote control is  
transmitting a command to the vehicle.  
Icon  
The signal icon will be displayed if a command is transmitted to  
the vehicle but the command page is not received.  
Icon  
The receive icon will be displayed while the remote control is  
receiving a page from the vehicle.  
Icon  
The auxiliary and sensor icons will display which auxiliary is oper-  
© 2006 directed electronics  
9
 
®
ating, or which security sensor (zone 2,4 or 7) is in Warn Away  
or alarm state.  
Icon  
The garage door icon—for use with optional 519H2.  
and  
Icons  
®
The above Warn Away displays when a security feature has been  
tripped, but not to full alarm.  
and  
Icons  
The above icons will display when a security feature has been  
tripped to a full alarm condition.  
Icon  
The ultrasonic sensor (detects motion within the vehicle) icon  
will display for full alarm by flashing for a few seconds and then  
display continuously until the page is cleared.  
Icon  
The tilt sensor icon will display for full alarm by flashing for a  
few seconds and then display continuously until the page is  
cleared.  
Icon  
The trunk icon will display for full alarm by flashing for a few  
seconds and then display continuously until the page is cleared.  
Icon  
The glass breakage sensor icon will display for full alarm by  
© 2006 directed electronics  
10  
 
flashing for a few seconds and then display continuously until  
the page is cleared.  
Icon  
®
The shock sensor icon will display for both Warn Away and full  
alarm by flashing for a few seconds and then display continu-  
ously until the page is cleared.  
Icon  
The battery icon always displays the current charge capacity  
remaining in the remote’s battery.  
Icon  
The remote start (option) icon displays when the vehicle is being  
remote started.  
Icon  
The field disturbance sensor icon will display for both Warn  
®
Away and full alarm by flashing for a few seconds and then  
display continuously until the page is cleared.  
Icon  
The shock sensor bar icon always displays the current sensitivity  
setting of the shock sensor.  
Icon  
®
The shock sensor “sensor” icon will display for both Warn Away  
and full alarm by displaying continuously until the page is  
cleared.  
© 2006 directed electronics  
11  
 
Icon  
The vibrator icon will always display if the remote is  
programmed for vibrator notification (see programming LCD  
remote section of the guide).  
Icon  
The ignition icon will display for full alarm by flashing for a few  
seconds and then display continuously until page is cleared.  
Icon  
The hood icon will display for full alarm by flashing for a few  
seconds and then display continuously until the page is cleared.  
Icon  
The vehicle icon always displays the current vehicle (maximum  
®
of 4 vehicles) being controlled by the remote. If a Warn Away  
or alarm trigger should occur at one of the other vehicles, that  
vehicle’s number will be displayed and the LCD will display that  
vehicle’s status. To change back to the original vehicle selected,  
press and release the program button until the vehicle number is  
shown.  
For example, If the remote was originally on vehicle number 1 and  
a trigger page was received for vehicle number 2, the remote will  
show the trigger alarm and show number 2 on the display. After  
clearing the page, press and release the program button until number  
1 is displayed. Now you can operate the alarm system on vehicle  
number 1.  
© 2006 directed electronics  
12  
 
Icon  
The door icon will display for full alarm by flashing for a few  
seconds and then display continuously until the page is cleared.  
Icon  
The arm icon will flash when the system is locking the doors and  
display continuously until the system is armed.  
Icon  
The disarm icon will flash when the system is unlocking the  
doors and display continuously until the system is disarmed.  
© 2006 directed electronics  
13  
 
transmitter functions  
This system uses a computer-based learn routine to learn the  
transmitter buttons. This makes it possible to assign any trans-  
mitter button to any system function. The transmitter initially  
comes programmed with Standard Configuration, but may also  
be customized by an authorized dealer. The buttons described in  
this manual correspond to a Standard Configuration transmitter.  
remote operation  
The system operates at 434 MHz and incorporates Directed’s propri-  
etary out-board technology transceiver. The high frequency combined  
with Binary Data communication achieves superior range with two-  
way communication.  
system signal paging features  
A page is the signal the control module sends to the remote control  
as confirmation of receipt of a command or alarm system status.  
When the remote control receives a page it will generate a page  
notification to the user (notifications are audible beeps and-or  
vibration) and the LCD Icons will display the current system status.  
Command Page  
When a command (arm/disarm, or auxiliary channel) from the  
remote control is sent and received, the system will send a  
command page back to confirm receipt.  
© 2006 directed electronics  
14  
 
Alarm Page  
If the alarm system is triggered while armed, an Alarm Page will be  
sent to the remote control. When the remote receives an Alarm  
Page, the LCD icons will display the alarm system status informa-  
tion and the remote control will generate beeps and-or vibration.  
An Alarm Page alert is a series of 5 groups of 4 rapid beeps  
(shock, trunk, door, ignition, or hood trigger) and the LCD icon  
that caused the alarm will display. The remote will beep and or  
vibrate every 60 seconds to alert the user that the alarm system  
was triggered and will continue until the alarm page is cleared.  
Page Recognition (Acknowledgement)  
To clear a page alert/notification, quickly press any button on  
the remote control. This can be performed at any time during or  
after the page notification has occurred.  
The remote control will not send a command to the system at  
this time; it will only clear future repeats of the page notification.  
The next time a button is pressed on the remote control it will  
send a command to the system.  
out of range notification  
If a command is issued from the remote, but the remote is set to  
the incorrect vehicle or is beyond the range of the vehicle to  
receive the command, the remote responds with 3 set of 2 quick  
beeps and the  
icon will flash 3-times.  
© 2006 directed electronics  
15  
 
programming LCD remote  
To enter programming mode  
Press and hold the  
button until one long beep is heard.  
P
Programming mode to customize the remote’s response is now  
entered.  
note:  
If no buttons are pressed within 5-seconds, pro-  
gramming mode will exit with 2-beeps.  
Beeps/Vibration On/Off  
Press  
to select beeps/vibration On/Off. Beeps alone, vibra-  
tion alone, beeps and vibration, or no beeps and vibration can be  
selected. Refer to the table below for these settings.  
Beep/Vibrate settings  
Programming response Icon display*  
Beeps only (default)  
Vibrate only  
1-beep  
Siren icon On  
1-vibrate  
Vibrate icon On  
Vibrate and siren icon  
On  
Beep & Vibrate  
1-beep and 1-vibrate  
Vibrate and siren  
icons Off  
No Beep and No Vibrate 1 long beep  
*Note:  
This is icon display during programming.  
© 2006 directed electronics  
16  
 
Illumination On/Off  
Press  
to select LCD backlight illumination On/Off. The  
LCD backlight will illuminate when a remote button is pressed,  
or an alarm status page is received.  
LCD Backlight settings Programming response  
ON  
1-beep, backlight ON  
2-beeps, backlight OFF  
OFF  
Page notification  
The remote control can be programmed to notify the user of a  
page (audibly beeping if the vehicle’s status changes, e.g. door  
unlocked, engine started, vehicle violation, etc.). On the LCD  
remote press  
to select page On/Off. One beep is page On,  
Two beeps is page Off. When programmed off the remote will not  
give any notification that a page was received from the vehicle.  
Note:  
no alarms  
will be notified to the  
If programmed Off,  
remote. Command information (armed/disarmed) will be noti-  
fied to the remote.  
To exit programming mode  
The LCD remote control will exit programming mode after 5-  
seconds of inactivity and will emit 2 long beep.  
© 2006 directed electronics  
17  
 
using your system  
The buttons described in this manual correspond to the standard  
configuration. Remember, this is not the only way your trans-  
mitter may be set up. It can be custom configured to meet your  
needs. See your installer for additional details.  
active arming  
You can arm the system by pressing  
of your remote for one  
second. When the system arms, from the vehicle you will hear a  
short siren sound, or chirp, and see the parking lights flash once.  
If the power door locks are controlled by the system, the doors  
will also lock. While the system is armed, the in-vehicle’s status  
LED will flash approximately once per second, indicating that  
the system is actively protecting your vehicle. If you hear a  
second chirp after arming and note that the in-vehicle’s status  
LED is flashing in groups, see the Diagnostics Section of this  
guide. This extra chirp is called Bypass Notification.  
The LCD remote responds to active arming with one beep and  
the  
icon will flash 5-times to indicate successful arming of  
the system.  
If the LCD remote beeps twice after arming, the system has detected  
an active sensor that should be checked. For example, a door open  
icon will be displayed flashing 5-times on the LCD screen.  
© 2006 directed electronics  
18  
 
passive arming  
The system can be programmed to arm itself automatically (called  
passive arming). If the system is programmed for passive arming, it  
will automatically arm 30 seconds after the ignition is turned off  
and the system detects that you have left the vehicle by opening and  
closing a door. Whenever the system is in its 30-second passive  
arming countdown, the in-vehicle status LED will flash twice as  
fast as it does when the system is armed. At the 20-second point of  
the countdown, the siren will chirp to indicate that the system is  
about to arm. At the 30-second point, the parking lights will flash  
to indicate that the system is armed.  
The LCD remote responds to passive arming with one beep and  
the  
icon will flash 3-times to indicate successful arming of  
the system.  
note: If any protected entry point (such as a door or a  
switch-protected trunk or hood) is open, the system will  
not passively arm (unless forced passive arming is pro-  
grammed on. See Programming Options section.) Addi-  
tionally, if a door, hood or trunk is triggered during the  
arming countdown, the 30-second countdown starts over.  
When armed your vehicle is protected as follows:  
®
Light impacts trigger the Warn Away signal. When triggered,  
the siren chirps and the parking lights flash for a few seconds.  
Heavy impacts trip a Triggered Sequence. The sequence  
consists of the siren sounding continuously and the parking  
lights flashing for a pre-programmed period, which can  
range in duration from 1 to 180 seconds.  
If a door is opened, the system will immediately start  
© 2006 directed electronics  
19  
 
chirping the siren and flashing the parking lights. Three  
seconds later, the siren output changes to a continuous blast.  
This progressive response gives you time to disarm the sys-  
tem with your LCD remote if you inadvertently open the  
door while the system is armed, while still providing instant  
response (even if the door is immediately closed).  
Turning on the ignition key will trip the same progressive re-  
sponse as opening a door.  
The optional starter kill prevents the vehicle’s starter from  
cranking.  
Any full trigger of the alarm system will immediately send an  
alarm page to your remote informing you that your vehicle  
should be checked.  
multi-level security arming  
Multi-Level Security Arming allows you to select which of the  
security system's inputs or sensors will be active and which will  
be bypassed at the time that the system is armed. (See the Table  
of Zones section of this guide.) Pressing  
seconds of arming the security system will activate the Multi-  
Level Security Arming feature. Each time is pressed again, a  
again within five  
different security level is selected. The different security levels  
can be selected as follows:  
Press  
once: The siren chirps once. The system is armed.  
a second time within five seconds: The parking  
Press  
lights flash twice. Zone 2 is now bypassed.  
Press a third time within five seconds: The parking  
lights flash three times. Zone 4 is now bypassed.  
© 2006 directed electronics  
20  
 
Press  
a fourth time within five seconds: The parking lights  
a fifth time within five seconds: The parking  
flash four times. Zone 7 is now bypassed.  
Press  
lights flash five times. Zones 2 and 4 are now bypassed.  
Press  
a sixth time within five seconds: The parking  
lights flash six times. Zones 2 and 7 are now bypassed.  
Press  
a seventh time within five seconds: The parking  
lights flash seven times. Zones 4 and 7 are now bypassed.  
Press  
an eighth time within five seconds: The parking  
lights flash eight times. All zones except zone 5 are now  
bypassed.  
note: Multi-Level Security Arming only applies to a sin-  
gle arming cycle. Once the system is disarmed and then  
re-armed, all the zones will be active again.  
After each press of the  
to reach the next level of security, the  
remote will emit normal arm notification (1 beep and 5 flashes  
of the  
icon). For easiest operation in reaching each level of  
after  
each notification.  
security, press  
immediately  
disarming  
To disarm the system, press  
. You will hear two chirps, and  
the parking lights will flash twice. If the power locks are  
connected to the system, the doors will unlock. If the siren chirps  
either four or five times when disarming, refer to the Diagnostics  
section of this guide. This is called Tamper Alert.  
© 2006 directed electronics  
21  
 
The remote will indicate disarm notification with 2 beeps and 5  
flashes of the icon. If disarming after the system has been  
triggered, the remote control will send a diagnostic notification  
as a reminder. These diagnostic notifications are:  
1. If a sensor triggered the system, the remote will emit 4 quick  
beeps and the LCD screen will indicate which sensor (5-  
flashes) tripped the alarm.  
2. If a switch (Zone 1, 3, 5, or 6) triggered the system, the  
remote will emit 4 quick beeps and the LCD screen will  
indicate which switch (5-flashes) tripped the alarm.  
3. If the system was triggered so many times that NPC is active  
the remote will emit the above notifications with 5 beeps  
instead of 4.  
© 2006 directed electronics  
22  
 
disarming without a transmitter  
This feature allows you to disarm the security system without the  
remote transmitter should it be lost, damaged, or disabled. In order  
to disarm the system without a remote transmitter, you must have  
the vehicle’s ignition key and know where the Valet button is  
located. Be sure to check with the installer for the location and the  
number of presses of the Valet button required to disarm the system.  
To disarm the security system,  
turn the ignition to the ON posi-  
tion. Press the Valet button the  
DRW-35  
preset number of times (one to  
five times) within 15 seconds. After five seconds the system will  
disarm. If the system does not disarm, you may have waited too long;  
turn the ignition off and on and try again.  
Location of Valet Button_________________________________  
Number of Pulses______________________________________  
important! The unit can be programmed to respond to  
one to five pulses of the Valet button for the disarm func-  
tion. Be sure to check with the installer for the desired  
programming.  
The LCD remote will indicate disarm notification with 4 quick  
beeps and 5 flashes of the  
and triggered zone icons.  
© 2006 directed electronics  
23  
 
dome light control  
security only  
The dome light activates for 30-seconds after the system is  
disarmed.  
Ignition controlled  
The dome light activates for 30-seconds after the ignition is  
turned Off.  
door controlled  
The dome light activates for 30-seconds after the system sees a  
door has closed. (If door was held open for longer than 3  
minutes the dome light will not illuminate.)  
full  
The dome light activates for 30-seconds after seeing door  
closure, ignition, or security disarm. (This is the factory setting.)  
silent mode  
To temporarily turn off the arm or disarm chirps, use Silent  
Mode™. Simply press  
for less than one second before  
arming or disarming, and the confirmation chirp(s) will be elim-  
inated for that one operation only. If you want the arm/disarm  
chirps turned off permanently, your dealer can do this for you.  
®
note: The Warn Away response to lighter impacts is  
bypassed if the system is armed using Silent Mode. This  
ensures that no chirps will be emitted by the siren in an  
area you want chirp-free. The system is still fully capable  
®
of triggering. Only the Warn Away response is bypassed.  
© 2006 directed electronics  
24  
 
The LCD remote responds with the normal arm/disarm notifi-  
cations in silent mode. (If the remote has beeps programmed  
On, the remote will beep.)  
panic mode  
note: On both remotes the panic button is the same color.  
LCD remote  
If you are threatened in or near your vehicle, you can attract  
attention by triggering the system with your LCD remote. Just  
press  
or  
button for approximately two seconds, and  
you will enter Panic Mode. The siren will sound and the parking  
lights will flash for the programmed siren duration. To stop  
Panic Mode at any time, press  
remote again.  
or  
button on the LCD  
The LCD remote responds with one beep and display of the  
icon upon entering Panic Mode.  
4-button remote  
If you are threatened in or near your vehicle, you can attract  
attention by triggering the system with your transmitter. Just  
press  
or  
for approximately two seconds, and you will  
enter Panic Mode. The siren will sound and the parking lights  
will flash for the programmed siren duration. To stop Panic Mode  
at any time, press  
, or  
on the remote transmitter again.  
© 2006 directed electronics  
25  
 
valet mode  
You can prevent your security system from automatically arming  
and triggering by using Valet Mode. This is very useful when  
washing the vehicle or having it serviced. In Valet Mode, the  
security system will not arm, even with the remote transmitter,  
but all convenience functions (door locks, trunk release, etc.)  
will continue to work normally.  
To enter or exit Valet Mode:  
1. Turn the ignition on.  
2. Turn the ignition off.  
DRW-35  
3. Press and release the Valet  
button within 10 seconds.  
The status LED will light solidly if you are entering Valet Mode,  
and it will go out if you are exiting Valet Mode.  
The remote will respond with 5-flashes of the  
icon and 2  
®
beeps on entering or exiting Valet Mode.  
To enter or exit Valet Mode using the transmitter:  
1. Open any vehicle door.  
Quickly press the following buttons in the sequence indicated.  
2. Press  
3. Press  
4. Press  
.
.
again.  
The in-vehicle status LED will light solidly if you are entering  
®
®
Valet Mode, and it will go out if you are exiting Valet Mode.  
© 2006 directed electronics  
26  
 
one-time bypass  
This feature (if programmed on) stops the alarm from arming or  
activating any outputs that are programmed to activate when the  
alarm is armed.  
One-time bypass will defeat the following actions:  
Passive arming: If programmed ON the alarm will not arm  
itself.  
If the remote is used to arm the alarm after exiting the vehicle:  
Window roll up: If programmed ON this output will not  
activate.  
Linked Auxiliary Outputs: If programmed to activate on  
arm, they will not activate.  
To activate one-time bypass:  
1. After parking turn the ignition off.  
2. Turn the ignition On for more than 1-second and less than  
3-seconds and then turned Off.  
3. The siren will chirp once to indicate one-time bypass has  
been activated.  
To cancel one-time bypass perform one of the following:  
Arm then disarm the alarm.  
Turn the ignition On for more than 3-seconds.  
nuisance prevention® circuitry  
®
Your system has Directed’s Nuisance Prevention Circuitry  
®
(NPC ). It prevents annoying repetitive trigger sequences due to  
© 2006 directed electronics  
27  
 
faulty door pin switches or environmental conditions such as  
thunder, jackhammers, airport noise, etc.  
Example  
If the alarm triggers three times within a 60-minute period and  
®
each time the same sensor or switch triggers the alarm, NPC will  
interpret those triggers as false alarms. After the third trigger,  
®
NPC ignores, or bypasses, that sensor or switch (along with any  
other sensors or switches sharing the same zone) for 60 minutes.  
If the bypassed sensor tries to trigger the system while it is being  
bypassed, the 60-minute bypass period will start over. This ensures  
that a sensor that continually triggers will remain bypassed.  
®
Doors are covered by NPC differently; if the alarm is triggered  
by an open door for three full cycles, the doors will be bypassed  
until the trigger ceases.  
note: Arming and disarming the system does not reset this  
function. In order to reset a bypassed zone, the same zone  
must not trigger for 60 minutes, or ignition is turned on.  
If testing your system, it is important to remember that the  
®
NPC programming can cause zones to be bypassed and  
appear to stop working. If five chirps are heard when dis-  
®
arming, NPC has been engaged. If you wish to clear the  
®
NPC memory, turn the ignition key on.  
®
NPC is On/Off programmable. See your dealer and the  
Programming section of this guide for more information.  
© 2006 directed electronics  
28  
 
auxiliary outputs (options)  
This system also supplies outputs that can control convenience  
options such as remote control trunk release and window automa-  
tion. Consult your dealer for available options for your system.  
Channel 2 Trunk release: When connected, pressing  
seconds will remotely release the vehicle trunk lid.  
for 1.5  
Channel 3 auxiliary output: When connected, pressing  
will immediately activate this output to control an  
additional convenience option.  
and  
Channel 4 auxiliary output: When connected, pressing  
will immediately activate this output to control an  
additional convenience option.  
and  
and  
and  
Channel 5 auxiliary output: When connected, pressing  
will immediately activate this output to control an  
additional convenience option.  
Channel 6 auxiliary output: When connected, pressing  
or  
will immediately activate this output to  
control an additional convenience option.  
The remote will respond with a page notification consisting of  
one long beep and for 4-seconds displays the channel number on  
the LCD screen. This occurs at the remote after the system has  
received the command to activate any of the Auxiliary outputs.  
© 2006 directed electronics  
29  
 
shock sensor adjustment  
To enter shock sensor adjustment mode:  
note:  
The system must be disarmed, and doors and other  
protected entries (zones 1 and 6) must be closed, and  
ignition (zone 5) must be off.  
1. Press and hold  
and  
buttons for 4-seconds.  
2. The siren will emit one long chirp and LCD remote will  
emit 1 long beep when the buttons on the remote are  
released (or 1 vibrate, or 1 long beep with vibrate) to indi-  
cate entry into shock adjustment mode.  
3. The word “SENSOR” on the LCD transmitter above the  
adjustment indicator bar  
will flash for the  
duration of shock adjustment mode. The sensor bar indi-  
cator will display the current sensor sensitivity setting.  
Increased sensitivity is indicated as the bar fills to the right.  
note:  
The LCD transmitter will also have the zone 2 icon  
and the alarm icon indicating.  
4. The in vehicle LED will illuminate continuously for the  
duration of shock adjustment mode.  
note:  
When the shock sensor adjustment mode is entered,  
all other timers and operations are bypassed until shock-  
sensor adjustment mode is exited.  
© 2006 directed electronics  
30  
 
Adjusting the Shock Sensor Setting  
note:  
When adjusting the shock sensor, ensure that the  
vehicle’s doors are closed.  
1. Increase Sensitivity—Press and release the  
button to  
increase shock sensor sensitivity by one step. The siren and  
remote will emit 2 chirps for each step increased in adjust-  
ment (and/or 1 vibrate if programmed). When the shock  
sensor adjustment reaches maximum sensitivity when the  
indicator bar is filled completely to the right  
. There are 21 levels of shock sensor  
adjustment, during sensor adjustment these levels are  
displayed on the indicator bar as listed below.  
note:  
When the arm and disarm are programmed to a sin-  
gle button, then the AUX button is used to increase the  
sensitivity setting of the sensor.  
© 2006 directed electronics  
31  
 
Sensor  
Adjustment  
Level  
Bar Number and Indication  
0
1
no bars displayed  
bar 1 flashes  
bar 1 solid  
2
bar 1 solid, bar 2 flashes  
bar 1-2 solid  
3
4
bar 1-2 solid, bar 3 flashes  
bar 1-3 solid  
5
6
bar 1-3 solid, bar 4 flashes  
bar 1-4 solid  
7
8
bar 1-4 solid, bar 5 flashes  
bar 1-5 solid  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
bar 1-5 solid, bar 6 flashes  
bar 1-6 solid  
bar 1-6 solid, bar 7 flashes  
bar 1-7 solid  
bar 1-7 solid, bar 8 flashes  
bar 1-8 solid  
bar 1-8 solid, bar 9 flashes  
bar 1-9 solid  
bar 1-9 solid, bar 10 flashes  
bar 1-10 solid  
© 2006 directed electronics  
32  
 
note:  
When the shock sensor adjustment mode is exited,  
the bar indicator will indicate continuously. For example if  
level 15 was being set (bars 1 through 7 indicating contin-  
uously, and bar 8 flashing), upon exiting adjustment mode  
bars 1 through 8 will indicate continuously.  
BAR 1  
BAR 10  
SENSOR LEVEL SETTING  
SHOWN AT MID-POINT  
2. Decrease Sensitivity—Press and release the  
button to  
decrease shock sensor sensitivity by one step. The siren and  
LCD remote will emit 1 chirp for each step decreased in  
adjustment (1 vibrate if programmed). The shock sensor  
adjustment reaches minimum sensitivity (sensor Off) when  
the indicator bar is empty  
.
3. Testing Sensor—Use the heel of the palm of your hand to  
strike the door pillar of the car after any increase or decrease  
in adjustment. The siren will chirp once if the impact was  
great enough to generate a full trigger. Pre-warn level is set  
automatically. When desired setting is reached, sensor  
adjustment mode can be exited.  
© 2006 directed electronics  
33  
 
Exit Shock Sensor Adjustment Mode:  
The adjustment mode will be exited if:  
No input from transmitter for 15-seconds.  
No input from sensitivity testing for 15-seconds.  
The ignition is turned On.  
The Valet button is pressed.  
The siren and LCD remote will emit 1 long beep and the  
vehicle’s LED will extinguish when shock adjustment mode is  
exited.  
Reset Shock Sensor to Default Setting:  
The shock sensor can be restored to a default setting of 10 to  
while in  
facilitate re-adjustment at any time  
adjustment mode.  
1. Simultaneously press the and  
buttons.  
2. The siren and LCD remote will emit 3 quick beeps to indi-  
cate the sensor has been reset to level 10 (mid-range).  
3. The system returns to shock sensor adjustment mode for  
further adjustment, if required.  
© 2006 directed electronics  
34  
 
diagnostics  
The microprocessor at the heart of your security system is  
constantly monitoring all of the switches and sensors that are  
connected to it. It detects any faulty switches and sensors and  
prevents them from disabling the entire system. The micropro-  
cessor will also record and report any triggers that occurred  
during your absence. Refer to the System Status Chirps and Table  
of Zones charts for diagnostic information.  
arming diagnostics  
If the system is armed while an input is active (door open, sensor  
triggering, etc.) the unit will chirp once when arming and then  
one more time a few seconds later. This is called Bypass  
Notification.  
note: Bypass Notification will not occur when using  
Silent Mode™ or if chirps have been programmed OFF.  
The security system will ignore the input that was active when  
the system was armed, until the input goes away. Three seconds  
later the system will monitor that input normally. For example,  
if your vehicle has interior light exit delay, and you arm the  
system before the interior light goes out, you may hear Bypass  
Notification chirps. Once the light shuts off, however, the doors  
are monitored normally.  
© 2006 directed electronics  
35  
 
disarming diagnostics  
Extra disarm chirps are the Tamper Alert. If four chirps are heard  
when disarming, the system was triggered in your absence. If five  
chirps are heard, a zone was triggered so many times that Nuisance  
®
Prevention Circuitry has bypassed that zone (see NPC section of  
this guide). The in-vehicle status LED will indicate which zone was  
involved. (See Table of Zones section of this guide.) The system will  
retain this information in its memory, and continue to chirp four  
or five times each time it is disarmed, until the next time the igni-  
tion key is turned on.  
system status chirps  
The siren will chirp when arming/disarming the system. The  
pattern of chirps will audibly report the system’s status as  
described below.  
Action  
Arm  
Number of Chirps  
1
Description  
System armed  
Arm  
1 (3-second delay), 1  
System armed with  
Bypass Notification  
Disarm  
Disarm  
2
4
System disarmed  
System disarmed with  
Tamper Alert  
Disarm  
5
System disarmed NPC®  
active  
© 2006 directed electronics  
36  
 
table of zones  
The zone number is the number of LED flashes used by the  
system to identify that input. The standard input assignments  
are listed below, along with spaces to write in any optional  
sensors or switches you have had installed.  
Zone - Number  
of LED Flashes  
Dealer-Installed  
Options  
Description  
1
Instant trigger - often used  
for trunk pinswitches  
2
Shock sensor input - a light  
impact activates warn away  
and a heavier impact activates  
full alarm.  
3
4
Door switch trigger  
Optional sensor inputs for  
warn away and full  
alarm notification.  
5
6
7
Ignition trigger  
Hood trigger  
Optional sensor inputs for  
warn away and full  
alarm notification.  
© 2006 directed electronics  
37  
 
interpreting zone diagnostics  
Warn Away responses are not reported by arming or disarming  
diagnostics. If you receive a Bypass notification when arming or  
a Tamper Alert notification when disarming, look at the in-  
vehicle status LED. Active or triggered zones will be indicated by  
a pattern of blinks by this LED.  
Example  
If Zone 3 was active or triggered, the in-vehicle LED will blink  
three times with a two-second pause. Then it will blink three  
times again, and repeat until the ignition is turned on.  
note: Your system stores the last six triggered zones in  
memory. If your system has been triggered but the LED  
has been reset by turning on the ignition, your dealer can  
still recall the last six zones that were triggered. Contact  
your dealer for details.  
code hopping  
The receiver and transmitters each use mathematical formulas  
called algorithms to change their codes each time the transmitter  
is used. This technology has been developed to increase the secu-  
rity of the unit. The control unit knows what the next codes  
should be. This helps to keep the transmitter "in sync" with the  
control unit even if you use the remote control out of range of  
the vehicle. However, if the transmitter has been pressed many  
times out of range of the vehicle, or if the battery has been  
removed, it may get out of sync with the control unit and fail to  
operate the system. To re-sync the remote control simply press  
© 2006 directed electronics  
38  
 
of the transmitter several times within range of the vehicle.  
The alarm will automatically re-sync and respond to the trans-  
mitters normally.  
owner recognition  
Owner Recognition is a feature available exclusively from Directed.  
®
Using the Directed Bitwriter , a hand-held programming tool,  
your dealer can program many of the system settings. The  
programmer makes it possible to program different settings for  
each transmitter that is used with the system. Then, whenever a  
specific transmitter is used, the system will recall the settings  
assigned to that transmitter. Owner Recognition lets up to four  
users of the system have different settings that meet their specific  
needs. It is almost like having four separate alarms in your vehicle,  
one for each user.  
note: Owner Recognition cannot be programmed with-  
out a Directed Bitwriter® and the necessary software.  
Check with your dealer for more information.  
rapid resume logic  
This Directed system will store its current state to non-volatile  
memory. If power is lost and then reconnected, the system will  
recall the stored state from memory. This means if the unit is in  
© 2006 directed electronics  
39  
 
Valet Mode and the battery is disconnected for any reason, such  
as servicing the car, when the battery is reconnected the unit will  
still be in Valet Mode. This applies to all states of the system  
®
including arm, disarm, VRS , and Valet Mode.  
power saver mode  
Your system will automatically enter Power Saver Mode while  
®
armed or in Valet Mode, after a period of time in which no  
operation has been performed. This lowers the current draw to  
the vehicle’s battery. Power Saver Mode takes over under the  
following conditions:  
Power Saver when the system is armed: After the system has  
been armed for 24 hours, the in-vehicle LED will flash at  
half its normal rate, decreasing the system's current draw.  
®
®
Power Saver in Valet Mode: When the system enters Valet  
Mode the in-vehicle LED illuminates steadily. If the vehicle  
is not used (ignition is not turned on) for a period of one  
®
hour while the system is in Valet Mode, the LED will shut  
®
off. If the system remains in Valet Mode, the LED will  
come back on the next time the ignition is turned on and  
then back off.  
© 2006 directed electronics  
40  
 
programming  
Programming options control what your system does during  
normal operation, and require few or no additional parts.  
However, some may require additional installation labor.  
The following is a list of the program settings, with the factory  
Bold:  
settings in  
Active arming  
(only with the remote) or passive arming (au-  
tomatic arming 30-seconds after the last door has been  
closed).  
on  
Arming/disarming confirmation siren chirps  
or off.  
on  
The ignition controlled door lock feature  
or off: With  
this feature on, the doors will lock three seconds after the  
ignition is turned on, and the doors are closed, and unlock  
when the ignition is turned off. The system will not lock the  
doors when the ignition is turned on with any door open.  
The bitwriter is not needed to program theses separately, it  
should be in the programming grid to do these 2 indepen-  
dently. Ignition lock and unlock are independent features  
and can be programmed separately.  
active door  
Passive door locking (with passive arming) or  
locking  
(only when arming with the remote). Passive locking  
allows the vehicle's doors to lock when the security system  
passively arms (after the 30 second countdown). This feature  
only works if passive arming has been programmed.  
© 2006 directed electronics  
41  
 
note: When programmed for passive arming and active  
lock, if the system is disarmed without a door being  
opened, the system will relock the doors when it passive-  
ly rearms.  
enabled  
Panic mode  
states have laws against siren capability in a moving vehicle.  
on  
/disabled with the ignition on: Some  
Forced passive arming  
or off: If your system is  
programmed for passive arming and the forced passive  
arming feature has been programmed on, the system will  
passively arm after one hour, even if a protected entry has  
been left open. This feature is useful if a door has been left  
ajar when leaving the vehicle. Forced passive arming ensures  
that the security system will be armed in every situation.  
note: When the system passively arms after one hour, the  
entry point that has been left open, and anything con-  
nected to the same zone, is bypassed and cannot trigger  
the system. However, the remaining inputs to the system  
are fully operational.  
off  
Automatic Engine Disable (AED) on or : The purpose of  
this feature is to protect the vehicle from being stolen at all  
times, regardless of whether or not the alarm is armed. If  
AED is programmed on, the starter of the vehicle will be dis-  
abled 30 seconds after the ignition is turned off. Once the  
key is turned off, the in-vehicle LED will flash slowly (one-  
half its normal armed rate) to indicate the AED arming  
cycle. Thirty seconds later, the starter of the vehicle will be  
disabled. To start the car, it will be necessary to disarm the  
system with the remote. It is also possible to disarm the AED  
© 2006 directed electronics  
42  
 
feature by turning the ignition key to the RUN position and  
®
pressing the Valet button the programmed number of  
®
times. AED is disabled when the system is in Valet Mode.  
®
note: This feature will only function if the Failsafe  
Starter Kill relay has been installed.  
30  
Full trigger response  
or 60 seconds: This determines how  
long the full triggered sequence lasts. Some states have laws  
regulating how long a security system can sound before it is  
considered a nuisance. If your installer is programming the  
security system with the Directed Bitwriter, the full triggered  
response can be programmed for any duration ranging from  
1 to 180 seconds.  
®
on  
Nuisance Prevention Circuitry  
or off: Please refer to the  
®
NPC section of this manual for a complete explanation of  
®
®
how NPC operates. If NPC is programmed off, the securi-  
ty system will respond to inputs from any sensor indefinitely.  
note: Because many states have laws regulating security  
systems, programming NPC® off may cause your system  
to violate state laws.  
© 2006 directed electronics  
43  
 
on  
Progressive door trigger or off: When the system is armed  
and a door is opened, the system responds with ten chirps  
prior to beginning the full triggered sequence. If an instant  
trigger is desired, the progressive door trigger can be pro-  
grammed off.  
®
®
Valet pulse count: The number of presses of the Valet  
button required to disarm the security system, AED, or the  
®
VRS system can be programmed from one to five presses. The  
one  
default setting is  
press.  
®
Siren tones and chirp volume: The output of the Revenger  
®
Soft Chirp siren consists of six different tones in sequence.  
Any of these tones can be eliminated by your dealer, result-  
ing in a unique, easily identifiable siren sound. The siren  
six decibels quieter  
chirps can be either full volume or  
the full alarm blast.  
than  
© 2006 directed electronics  
44  
 
installation options  
The system has many options that may require extra parts and  
labor. Some of the possibilities are listed here.  
Progressive unlocking: In most cars with electric power door  
locks, the system can be configured so that when the system is  
disarmed, only the driver’s door unlocks. A second press of the  
button unlocks the other doors.  
®
®
Vehicle Recovery System (VRS ): VRS is an anti-carjacking  
device designed to help in the safe recovery of your vehicle  
in case of a carjacking. Please refer to the Vehicle Recovery  
System section of this guide for a complete explanation of  
how the Vehicle Recovery System operates.  
vehicle recovery system (vrs®)  
®
The optional VRS feature is designed to ensure that any unautho-  
rized user of your vehicle (even if using your keys and remote control)  
will not be able to permanently separate you from your vehicle.  
®
The VRS cannot prevent a carjacking attempt; however, it does  
ensure that if your vehicle is taken by an unauthorized user, it will  
be disabled (after several progressive warnings) as safely as  
®
possible. Should a carjacking occur, the VRS allows you to  
concern yourself with your personal safety without worrying  
about your property.  
© 2006 directed electronics  
45  
 
®
Directed has engineered this vehicle security system, the Failsafe  
®
Starter Kill, and the VRS feature to provide the best combina-  
tion of personal safety and property protection available. When  
properly installed, the system can never inadvertently stop your  
vehicle in traffic or on railroad tracks while the vehicle is in oper-  
ation. It is unlike other systems that shut down your engine  
while it is running. This system is designed to perform starter in-  
®
terrupt, or starter kill. The Failsafe Starter Kill cannot shut  
down an already-running engine – it can only prevent an engine  
from starting in the first place.  
important! Any installation that allows this product to  
shut down a vehicle's engine when it is running is con-  
trary to the product’s design and intended usage, and  
Directed hereby expressly disclaims any liability resulting  
therefrom.  
arming the vrs®  
To arm the VRS , turn the ignition to the ON position and press  
®
the arm button on the remote transmitter for one second. The  
parking lights will flash and the siren will chirp once. This can be  
done before driving or while driving the vehicle. Once the system  
is armed, it will initiate its triggered sequence (see below) if any  
door is opened and closed. If you are forced from the vehicle, the  
system will trigger as the door is opened and closed. This is how  
the system works to combat intersection carjacking. To protect  
®
against parking lot carjacking, arm the VRS before leaving the  
vehicle. The system will now trigger automatically the next time  
you or anyone drives the vehicle. This helps to protect the vehicle  
© 2006 directed electronics  
46  
 
if someone takes your keys and remote transmitter by force in a  
parking lot.  
®
note: If the VRS system is armed while operating the vehi-  
cle and not disarmed prior to leaving the vehicle, it is still  
armed and will trigger the next time the vehicle is driven.  
vrs® triggered sequence  
Fifteen seconds after the last door has closed, the in-vehicle LED  
will begin flashing. This delay is intended to allow you time to  
distance yourself from your vehicle in the event of a carjacking.  
Forty-five seconds later, the siren begins chirping and the park-  
ing lights begin flashing. This time could be used to notify au-  
thorities that your vehicle has been hijacked, and tell them what  
®
the VRS will do next.  
Fifteen seconds after the siren chirps begin, the siren’s output will  
change to a continuous blast.  
®
From this point on, when the ignition key is turned off, the VRS  
will immediately turn on the starter kill. This will prevent the  
vehicle from being restarted, thus immobilizing it at that spot.  
Three minutes after the constant siren output begins, the flashing  
parking lights and the siren will stop. The starter kill will remain  
active until the system is disarmed. If the door is opened or the  
ignition is turned off and on in an attempt to restart the car, the  
siren and light flashing will begin again.  
© 2006 directed electronics  
47  
 
disarming the vrs®  
Take the time to familiarize yourself with the VRS triggering se-  
quence and the disarm procedure. It is important to recognize  
®
®
and identify the VRS trigger sequence and know how to disarm  
it in case of accidental activation.  
®
Once the VRS is armed, it does not disarm automatically. You  
must disarm it the next time you operate the vehicle. You must  
disarm it with one of the following procedures:  
If the system has not entered the triggered sequence (siren has  
not started chirping):  
1. Turn the ignition on.  
2. Press  
on the transmitter for one second. The  
lights will flash and the siren will chirp twice.  
If the system has entered the triggered sequence (siren has begun  
chirping), pressing the disarm button of the transmitter will not  
®
®
®
disarm VRS . To disarm the VRS during a VRS trigger sequence:  
1. Turn the ignition on.  
2. Press the Valet button the pre-  
DRW-35  
programmed number of times to  
®
disarm the VRS system.  
®
note: If the VRS system has begun its chirping sequence,  
the ignition must be turned off, then on to disarm. If you  
are driving the vehicle at the time, pull to a safe place  
away from traffic and follow the triggered sequence dis-  
arm procedure.  
© 2006 directed electronics  
48  
 
programming options  
See your dealer for further details on the options listed below  
available with this system.  
Automatic Engine Disable: Prevents the vehicle from being started  
even if the vehicle is not armed after turning the ignition Off and  
exiting the vehicle.  
Comfort Closure: Windows will close upon locking the vehicle.  
Dual Sensor Trigger: If programmed On both the onboard and at  
least one of the optional sensors need to be triggered within 1-  
second of each other for full alarm.  
note: In dual sensor mode, the LCD remote will report  
showing both zones that tripped the alarm. The in-vehicle  
LED will flash to indicate only the last sensor of the pair  
which tripped the alarm.  
Forced Passive Arming: If passive arming is on and a door is left  
open the system will be armed after 30-seconds.  
High Security Disarm: If the system is triggered this feature allows  
the user to silence the siren and reset the system to the armed  
state without having to visually check the system status.  
Multi-level Arming: Allows bypassing of user selected alarm zones  
of the vehicle.  
Grouped Arming: Allows bypassing of the group of alarm zones  
for warn-away, or both warn-away and full alarm of the vehicle.  
© 2006 directed electronics  
49  
 
Panic with Ignition Off: Prevents the Panic button on the remotes from  
activating panic with ignition On (not allowed in some states).  
Parking Light Supervision: The parking lights will illuminate for  
30-seconds after disarming the system or turning the ignition off.  
Remote Start Reporting: This channel 3 program option allows  
bypass of the security inputs that would trigger an alarm when  
activating an added optional remote start system, but still retains  
a high level of security.  
Retained Accessory Power: This output from the security system  
can be connected to vehicle accessories. After the ignition has  
been turned off, it will continue to supply power until a door  
has been open and closed.  
security & convenience expansions  
Here we have listed only some of the many expansion options  
available. Please contact your dealer for a complete explanation  
of all the options available to you.  
Audio Sensor: Metal on glass, glass cracking, and breaking glass  
each produce distinctive acoustic signatures. The 506T audio  
sensor uses a microphone to pick up sounds, and then analyzes  
them with proprietary acoustic software to determine if the glass  
has been struck.  
Backup Battery: The 520T keeps the system armed, triggers the  
© 2006 directed electronics  
50  
 
alarm and keeps the starter kill active if main battery power is  
disconnected.  
Field Disturbance Sensor: An invisible dome of coverage is estab-  
lished by installing the 508D "radar" sensor. Your security  
system can then react to any intrusions into this field with the  
triggered sequence.  
Garage Door:  
Remote control of your system can go beyond  
your vehicle. You can also control your automatic garage door  
using the 519H2 garage door opener with your remote control.  
Ask you dealer for details. Additional parts and labor required.  
®
Headlight and Parking Light Automation: The 545T Nite-Lite  
will automatically turn on your parking and headlights when it  
gets dark. In addition, the 545T will turn your headlights on  
whenever the windshield wipers are used. A transmitter function  
can also be used to turn on your parking and headlights for a  
programmed time.  
Power Trunk Release: The channel two output of the system can  
operate a factory power release for the vehicle’s trunk or hatch.  
(An additional relay may be required.) If the factory release is not  
power activated, then Directed's 522T trunk release solenoid can  
often be added.  
Power Window Control: Automatic power window control is pro-  
vided with the 529T and 530T systems.  
Tilt Sensor:  
The 507M tilt sensor can be added to your system  
© 2006 directed electronics  
51  
 
to protect your car when its parked. It can protect your vehicle  
from being lifted to protect your expensive rims.  
Valet Start System: For the ultimate in convenience, the Valet  
start system can start your vehicle, monitor engine functions,  
and power your climate control system with a push of a button.  
Over-rev protection, open-hood lockout, brake pedal shutoff,  
and automatic timer shutoff are all included. (This feature is  
only for automatic transmission, fuel-injected vehicles.)  
Ultrasonic Sensor:  
Providing a field of protection inside your car  
using the 509U Ultrasonic sensor to protect your belongings.  
© 2006 directed electronics  
52  
 
glossary of terms  
ASK Amplitude Shift Keying—a method of transmitting data.  
Control Unit: The "brain" of your system. Usually hidden under  
the dash area of the vehicle. It houses the microprocessor which  
monitors your vehicle and controls all of the system's functions.  
Fail Safe Starter Kill: An automatic switch controlled by the secu-  
rity system which prevents the vehicle’s starter from cranking  
whenever the system is armed. The vehicle is never prevented  
from cranking when the system is disarmed, in Valet mode, or  
should the starter interrupt switch itself fail. Your system is ready  
for this feature, however installation may require additional labor.  
Input: A physical connection to the system. An input can be  
provided by a sensor, pinswitch or through an existing system in  
the vehicle, such as ignition or courtesy lights.  
In-vehicle status LED: A light mounted somewhere in the vehicle.  
It is used to indicate the status of your system. It is also used to  
report triggers and faults in the system or sensors.  
LCD: This is a Liquid Crystal Display used on your remote trans-  
mitter to display your vehicles status/alarm information.  
Shock Sensor: This is a sensor mounted in the vehicle that is  
designed to pick up impacts to the vehicle or glass.  
Siren: Noise generating device usually installed in the engine  
compartment of the vehicle. It is responsible for generating the  
© 2006 directed electronics  
53  
 
"chirps" you hear, as well as the six tones you hear while the  
alarm is triggered.  
Transmitter: Hand-held, remote control which operates the  
various functions of your system.  
Trigger or Triggered Sequence: This is what happens when the  
alarm "goes off" or "trips". The triggered response of your  
system consists of the siren sounding and parking light flashing  
for the programmed duration.  
Valet Button: A small push-button switch mounted somewhere  
inside the vehicle. It is used to override the alarm when a trans-  
mitter is lost or damaged, or to enter or exit Valet mode.  
®
Warn Away Response: Lighter impacts to the vehicle will generate  
the Warning Zone response. It consists of several seconds of siren  
chirps and parking light flashes.  
Zone: A zone is a separate input that the alarm can recognize as  
unique. Each input to the system is connected to a particular  
zone. Two or more inputs often share the same zone.  
© 2006 directed electronics  
54  
 
QUICK REFERENCE GUIDE  
To arm using your LCD remote  
You can activate, or arm, the system by pressing  
on your remote for one  
second. When the system arms, you will hear a short siren sound, or chirp, and  
the parking lights will flash once. If the vehicle’s power door locks have been  
connected to the system, the doors will lock.  
To disarm using your LCD remote  
To disarm the system, press . You will hear two chirps, and the parking  
lights will flash twice. If power locks are connected to the system, the doors will  
unlock. If the siren chirps either four or five times when disarming, see  
Diagnostics section. This is called Tamper Alert.  
Arming while driving  
Press on your remote for two second while the vehicle is running. The  
system will chirp once and then once more to indicate that the ignition is on.  
Disarming without a LCD remote  
Turn on the ignition. Press and release the Valet button the programmed  
®
number of times within 15 seconds. After five seconds, the system will disarm.  
If it does not, you may have waited too long. Turn the ignition off and on and  
try again.  
®
To enter or exit Valet Mode  
Turn ignition to RUN position, then turn to OFF position. Press and release  
®
the Valet button within 10 seconds. The in-vehicle status LED will light solid  
®
®
if you are entering Valet Mode, and it will go out if you are exiting Valet  
Mode.  
To activate Panic Mode  
Press and hold or  
down for approximately two seconds.  
To exit Panic Mode  
Press or on the remote.  
To activate Silent Mode™  
Press briefly before arming or disarming, and the confirmation chirp(s)  
will be eliminated for that one operation only.  
®
Location of Valet Button_______________________________  
®
Number of Valet Button pulses for disarming_____________  
© 2006 directed electronics  
55  
 
The company behind this system is Directed Electronics  
Since its inception, Directed has had one purpose, to provide consumers with the  
finest vehicle security and car stereo products and accessories available. The recipient  
of more than 20 patents in the field of advanced electronic technology, Directed is  
ISO 9001 registered.  
Quality Directed Electronics products are sold and serviced throughout North America  
and around the world.  
Call (800) 274-0200 for more information about our products and services.  
®
Directed is committed to delivering world class quality products  
and services that excite and delight our customers.  
Directed Electronics  
Vista, CA 92081  
© 2006 Directed Electronics. - All rights reserved  
G3302P 11-06  
 

Radio Shack Car Stereo System PLCD41MP User Guide
Radio Shack Universal Remote 3 in One Pocket Remote User Guide
RCA Stereo Receiver SUBWOOFER SATELLITE SPEAKERS User Guide
Reebok Fitness Home Gym RBBE07870 User Guide
Rival Mixer HM 708 User Guide
Rosen Entertainment Systems Car Video System AV CY0801 G42 User Guide
Samsung Cordless Telephone SGH t609 User Guide
Samsung Home Theater System AH68 01959S User Guide
Samsung Range NE595N0PBSR User Guide
Scag Power Equipment Lawn Mower SWZ 19KAI User Guide