Transition Networks TV Converter Box SGETF1013 100 User Manual

COMPLIANCE INFORMATION  
UL Listed  
1000BASE-TX to 1000BASE-SX/LX  
C-UL Listed (Canada)  
CISPR/EN55022 Class A  
EN55024  
Media Converters  
SGETF10xx-100  
FCC Regulations  
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant  
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful  
interference when the equipment is operated in a commercial environment. This equipment generates,  
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the  
instruction manual, may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference, in which case the user will be  
required to correct the interference at the user’s own expense.  
USER’S GUIDE  
TRANSITION Networks SGETF10xx series Gigabit Ethernetmedia converters  
connect 1000BASE-TX shielded or unshielded twisted-pair copper cable to  
1000BASE-SX or 1000BASE-LX multimode or singlemode fiber-optic cable.  
Canadian Regulations  
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on  
the radio interference regulations of the Canadian Department of Communications.  
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables  
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique  
édicté par le ministère des Communications du Canada.  
1000BASE-T Copper  
European Regulations  
Warning  
This is a Class A product. In a domestic environment this product may cause radio interference in which  
case the user may be required to take adequate measures.  
Achtung !  
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes  
Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen  
werantwortlich ist.  
1000BASE-SX/LX Fiber  
Attention !  
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des  
interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques  
appropriées  
SGETF1013-100  
SGETF1018-100  
Provides an RJ-45 twisted-pair copper  
1000BASE-T connector and an RX  
(receive) and TX (transmit) SC connector  
to 850 nm 1000BASE-SX multimode  
fiber-optic cable.  
Provides an RJ-45 twisted-pair copper  
1000BASE-T connector and an RX  
(receive) and TX (transmit) MT-RJ  
connector to 850 nm 1000BASE-SX  
multimode fiber-optic cable.  
SGETF1014-100  
SGETF1025-100  
Provides an RJ-45 twisted-pair copper  
1000BASE-T connector and an RX  
(receive) and TX (transmit) SC connector  
to 1300 nm 1000BASE-LX singlemode  
fiber-optic cable.  
Provides an RJ-45 twisted-pair copper  
1000BASE-T connector and an RX  
(receive) and TX (transmit) MT-RJ  
connector to 1300 nm 1000BASE-LX  
singlemode fiber-optic cable.  
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE  
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in  
damage to the public telephone network.  
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten  
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG  
zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über  
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer  
Konformität.  
SGETF1015-100  
Provides an RJ-45 twisted-pair copper  
1000BASE-T connector and an RX  
(receive) and TX (transmit) SC connector  
to 1300 nm 1000BASE-LX singlemode  
fiber-optic cable.  
Trademark Notice  
All registered trademarks and trademarks are the property of their respective owners.  
SGETF10xx in the Network . . . . . . . .2  
Installation . . . . . . . . . . . . . . . . . . . .2  
Operation . . . . . . . . . . . . . . . . . . . . .4  
Fault Isolation and Correction . . . . .5  
Cable Specifications . . . . . . . . . . . . .6  
Technical Specifications . . . . . . . . . .7  
Compliance Information . . . . . . . . . .8  
SGETF1017-100  
Copyright Restrictions  
© 2001 TRANSITION Networks.  
All rights reserved. No part of this work may be reproduced or used in any form or by any means –  
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.  
Provides an RJ-45 twisted-pair copper  
1000BASE-T connector and an RX  
(receive) and TX (transmit) SC connector  
to 1550 nm 1000BASE-LX singlemode  
Printed in the U.S.A.  
33197.C  
 
fiber-optic cable.  
Install Cable  
CABLE SPECIFICATIONS  
Fiber Cable  
COPPER  
NOTE: The SGETF10xx series media converter auto-negotiation feature  
allows the media converter to bring up the copper link in the highest  
mode possible for ALL the attached network devices.  
MULTIMODE  
Fiber Optic Cable Recommended:  
Optional:  
62.5 / 125 µm multimode fiber  
100 / 140 µm multimode fiber  
85 / 125 µm multimode fiber  
50 / 125 µm multimode fiber  
850 nM  
1.  
Locate or build 1000BASE-TX-compliant cables with male RJ-45  
connectors installed at both ends.  
SGETF1013  
2.  
Connect RJ-45 connector at one end of cable to media converter  
RJ-45 port connector.  
Fiber Optic Transmitter Power:  
Fiber Optic Receiver Sensitivity:  
Link Budget:  
Typical Maximum Cable Distance*:  
SGETF1018  
min: -10.0 dBm  
min: -17.0 dBm  
7.0 dB  
max: -4.0 dBm  
max: -0.0 dBm  
3.  
Connect RJ-45 connector at other end of cable to 1000BASE-TX-  
compliant device RJ-45 port connector.  
220 meters  
850 nM  
Fiber Optic Transmitter Power:  
Fiber Optic Receiver Sensitivity:  
Link Budget:  
min: -9.5 dBm  
min: -17.0 dBm  
7.0 dB  
max: -4.0 dBm  
max: -0.0 dBm  
FIBER  
1. Locate or build 1000BASE-SX/LX-compliant fiber cable with male  
two-stranded TX to RX connectors installed at both ends.  
Typical Maximum Cable Distance*:  
220 meters  
SINGLEMODE  
Fiber Optic Cable Recommended:  
SGETF1014  
9 µm singlemode fiber  
1300 nM  
TX  
TX  
Fiber-optic Transmitter Power:  
Fiber-optic Receiver Sensitivity:  
Link Budget:  
min: -13.0 dBm  
min: -20.0 dBm  
7.0 dB  
max: -3.0 dBm  
max: -3.0 dBm  
RX  
RX  
Typical Maximum Cable Distance*:  
SGETF1015  
Fiber-optic Transmitter Power:  
Fiber-optic Receiver Sensitivity:  
Link Budget:  
5 kilometers  
1300 nM  
min: -5.0 dBm  
min: -20.0 dBm  
15.0 dB  
2. Connect cable with connector installed at TX location on media  
converter to RX location on attached device.  
max: -0.0 dBm  
max: -3.0 dBm  
3. Connect cable with connector installed at RX location on media  
converter to TX location on attached device.  
Typical Maximum Cable Distance*:  
SGETF1017  
25 kilometers  
1550 nM  
Fiber-optic Transmitter Power:  
Fiber-optic Receiver Sensitivity:  
Link Budget:  
min: -3.0 dBm  
min: -23.0 dBm  
20.0 dB  
max: -2.0 dBm  
max: -3.0 dBm  
Power the Media Converter  
1. Install power adapter cord at back of media converter.  
Typical Maximum Cable Distance*:  
SGETF1025  
65 kilometers  
1550 nM  
2. Connect power adapter plug to AC power.  
Fiber-optic Transmitter Power:  
Fiber-optic Receiver Sensitivity:  
Link Budget:  
min: -9.5 dBm  
min: -20.0 dBm  
20.0 dB  
max: -3.0 dBm  
max: -3.0 dBm  
3. Verify that media converter is powered by observing illuminated  
LED(s).  
Typical Maximum Cable Distance*:  
65 kilometers  
*Actual distance dependent upon physical characteristics of network installation.  
Copper Cable  
Category 5 twisted-pair copper wire is required. Either shielded twisted-pair (STP) or  
unshielded twisted-pair (UTP) can be used. DO NOT USE FLAT OR SILVER SATIN WIRE.  
CATEGORY 5:  
Gauge  
24 to 22 AWG  
Attenuation  
Maximum Cable Distance:  
22.0 dB /100m @ 100 MHz  
100 meters  
The Gigabit Ethernetnetwork uses all four wire pairs. The active pairs are pins 1 & 2,  
pins 3 & 6, pins 4 & 5, and pins 7 & 8. Use only dedicated wire pairs (such as blue/white  
& white/blue, orange/white & white/orange) for the active pins. NOTE: Straight-  
 
through/crossover configuration is automatic.  
OPERATION  
FAULT ISOLATION and CORRECTION  
If the media converter fails, isolate and correct the fault by determining the  
answers to the following questions and then taking the indicated action:  
Using Status LEDs  
Use the status LEDs to monitor media converter operation in the network.  
1.  
Is the P(o)W(e)R LED on the media converter illuminated?  
P(o)W(e)R Steady LED indicates connection to  
NO  
external AC power.  
Is the power cord properly installed in the media converter and at  
the external power source?  
PWR  
RXF  
(Fiber receive) Flashing LED  
indicates reception of data on fiber  
link.  
Does the external power source provide power?  
Contact Technical Support: (800) 260-1312.  
LKF  
LKC  
RXF  
RXC  
YES  
LKF  
RXC  
LKC  
(Fiber link) Steady LED indicates  
fiber link connection.  
Proceed to step 2.  
2.  
3.  
Is the LKC LED on the media converter illuminated?  
(Copper receive) Flashing LED indicates reception of data on  
copper link.  
NO  
Check twisted-pair cables for proper connection.  
Check twisted-pair cables for connection of all four pairs.  
Contact Technical Support: (800) 260-1312.  
(Copper link) Steady LED indicates copper link connection.  
YES  
Proceed to step 3.  
Is the LKF LED on the media converter illuminated?  
NO  
Check fiber cables for proper connection.  
Verify that TX and RX cables on media converter are connected to  
RX and TX ports, respectively, on other device.  
Contact Technical Support: (800) 260-1312.  
YES  
Proceed to step 4.  
4.  
Is the RXC LED on the media converter flashing?  
NO  
If there is NO ACTIVITY on the 1000BASE-TX port, proceed to step 5.  
If there is ACTIVITY on the 1000BASE-TX port, disconnect and  
reconnect the 1000BASE-TX cable to restart the initialization process.  
Restart the workstation to restart the initialization process.  
Contact Technical Support: (800) 260-1312.  
YES  
Proceed to step 5.  
5.  
Is the RXF LED on the media converter flashing?  
NO  
If there is NO ACTIVITY on the 1000BASE-SX/LX port, continue  
below  
If there is ACTIVITY on the 1000BASE-SX/LX port, disconnect and  
reconnect the fiber cable to restart the initialization process.  
Restart the workstation to restart the initialization process.  
Contact Technical Support: (800) 260-1312.  
YES  
Contact Technical Support: (800) 260-1312.  
 

Techno Source Handheld Game System 20720 User Manual
Topcom Network Router WBR 244 User Manual
Toshiba All in One Printer 4520C User Manual
Toshiba CRT Television 27DF47 User Manual
Tripp Lite Surge Protector 6SPDX 15 User Manual
Ultra Start Automobile Alarm 1250 User Manual
ViewSonic Flat Panel Television VPW5500 User Manual
Vivitar Telescope VIV TEL 76700 User Manual
Vulcan Hart Carpet Cleaner VHX10G User Manual
Waterpik Technologies Electric Toothbrush WP 100 User Manual