Addonics Technologies Computer Drive RCHDSAES User Manual

Enclosure Overview  
top cover  
Addonics  
shock  
absorbers  
T E C H N O L O G I E S  
2.5” SATA  
switch  
hard drive  
Ruby Combo Hard Drive  
RCHDSAES & RCHDSAEU  
PCB  
bottom cover  
User’s Guide  
Step 1 Separate the top from the bottom cover of the drive enclosure by  
loosening the screw as shown on the photo.  
Version 1.0  
FCC Warning Statement  
This equipment has been tested and found to comply with the limits for a class B digital  
device pursuant to Part 15 of the FCC rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy. If not installed and  
used in accordance with the instructions, it may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If the equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment on and off, the user  
is encouraged to try and correct the interference by one or more of the following  
suggestions.  
Step 2 Align the SATA connector in the 2.5” hard drive with the SATA connector  
on the PCB.  
Step 3 Wrap the shock absorbers around the hard drive and PCB.  
Reorient or relocate the receiving antenna  
Increase the distance between the equipment and the receiver  
Connect the equipment to a different power outlet other than the one where receiver is  
connected  
Consult a certified television or radio technician  
 
Model: RCHDSAES  
Model: RCHDSAEU  
*Note: The Ruby combo hard drive with the eSATA interface must be connected  
to a SATA controller with hot swap capability in order to add and remove drive  
cartridge without rebooting. Please consult your motherboard or the add-in card  
manufacturer to determine hot swap support on your SATA controller. All of the  
Addonics SATA Host Controllers are hot swap capable.  
For External Application:  
For External Application:  
eSATA cable  
Power adapter  
Step 1: Connect the eSATA cable to the eSATA port at the back of the  
enclosure. The other end of the cable connects to the eSATA port on the USB2.0  
to eSATA adapter. Plug the adapter to a USB port on your system.  
eSATA cable  
Power adapter  
Red LED showing  
adapter access  
Step 1: Connect the eSATA cable to the eSATA port at the back of the  
enclosure. The other end of the cable connects to an eSATA host controller.  
eSATA cable from  
Ruby enclosure  
USB Port  
Step 2: Plug into the power jack located at the back of the enclosure, the power  
adapter. This power connection provides power to the ruby enclosure.  
Green LED showing  
adapter connectivity  
Step 3: Set the switch to EXT position. The power LED will light up to indicate  
power is provided to the drive.  
Step 2: Plug into the power jack located at the back of the enclosure, the power  
adapter. This power connection provides power to the ruby enclosure.  
Step 3: Set the switch to EXT position. The power LED will light up to indicate  
power is provided to the drive.  
 
For Internal Application: (Applies to both models)  
Technical Support  
If you need assistance to get your unit functioning properly, please call Addonics  
Technical Support. Our technical staff will be happy to assist you, but they will  
need your help to do so. Calling the technical support staff without all the proper  
information can be both time consuming and frustrating. Here are some tips to  
help you out:  
Drive  
enclosure  
MODEL NUMBER Please have this number on hand.  
SYSTEM INFORMATION Type of computer, peripherals, etc.  
OPERATING SYSTEM What version of Windows  
Drive  
cradle  
WHAT’S THE TROUBLE? – Give enough information  
about your problem so that we can recreate and diagnose it.  
FREE Software Drivers for all Addonics Technologies  
Products are available 24 hours per day at the  
World Wide Web Site: www.addonics.com.  
Contact Information  
Step 1: Connect a SATA cable to the 7-pin SATA data connector to the SATA  
interface of the cradle.  
Phone:  
Fax:  
408-433-3899  
408-433-3898  
Email:  
Internet:  
Step 2: Connect a 15-pin SATA power cable from your system’s power supply to  
the SATA interface of the cradle. This power connection provides power to the  
ruby drive cartridge system.  
TECHNICAL SUPPORT  
Phone:  
Hours:  
Email:  
408-433-3855  
8:30 am - 6:00 pm PST  
Step 3: Slide the Ruby enclosure inside the cradle. To turn ON the drive  
enclosure, place switch on INT position.  
 

ADC Network Card H4TU C 319 List 1 Line Unit User Manual
Addonics Technologies Computer Drive AD5SAPM User Manual
AEG Blender M 2600 User Manual
AEG Microwave Oven MCC3880E M User Manual
Alliance Laundry Systems Washer UW50P 4 User Manual
Allied Telesis Network Card GE8 User Manual
ATON Stereo Receiver AIR5 User Manual
Audiovox Stereo Amplifier AXT 1200 User Manual
Avital Automobile Alarm MAXX1 User Manual
Banner American Products Laminator MIGHTYLAM 2700 User Manual