Alpine Car Stereo System TME M770 User Manual

FOR CAR USE ONLY/ NUR FÜR AUTOMOBIL GEBRAUCH/ POUR APPLICATION AUTOMOBILE UNIQUEMENT/  
PARA USO EN AUTOMÓVILES/ SOLO PER L'UTILIZZO IN AUTOMOBILE/ ENDAST FÖR BILBRUK/  
R
EN  
DE  
FR  
ES  
IT  
TME-M770  
6.5-INCH TOUCH PANEL WIDE LCD MONITOR  
• OWNER'S MANUAL  
Please read before using this equipment.  
• BEDIENUNGSANLEITUNG  
Lesen Sie diese Bedienungsanleitung bitte vor  
Gebrauch des Gerätes.  
• MODE D'EMPLOI  
Veuillez lire avant d’utiliser cet appareil.  
• MANUAL DE OPERACIÓN  
Léalo antes de utilizar este equipo.  
• ISTRUZIONI PER L’USO  
Si prega di leggere prima di utilizzare il  
attrezzatura.  
• ANVÄNDARHANDLEDNING  
Innan du använder utrustningen bör du läsa  
igenom denna användarhandledning.  
ALPINE ELECTRONICS, INC.  
1-1-8 Nishi Gotanda,  
Shinagawa-ku, Tokyo 141-0031, Japan  
Phone 03-5496-8231  
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.  
6-8 Fiveways Boulevarde Keysborough,  
Victoria 3173, Australia  
ALPINE ELECTRONICS FRANCE S.A.R.L.  
(RCS PONTOISE B 338 101 280)  
98, Rue de la Belle Etoile, Z.I. Paris  
Nord II, B.P. 50016, 95945, Roissy  
Charles de Gaulle Cedex, France  
Phone 01-48 63 89 89  
SE  
CH  
Phone 03-9769-0000  
ALPINE ELECTRONICS OF AMERICA, INC.  
19145 Gramercy Place, Torrance,  
California 90501, U.S.A.  
ALPINE ELECTRONICS Gm b H  
Frankfurter Ring 117, 80807 München,  
Germany  
ALPINE ITALIA S.p .A.  
Viale C. Colombo 8,  
20090 Trezzano Sul Naviglio (MI), Italy  
Phone 02-48 47 81  
Phone 1-800-ALPINE-1 (1-800-257-4631)  
Phone 089-32 42 640  
ALPINE ELECTRONICS OF CANADA, INC.  
7300 Warden Ave., Suite 203, Markham,  
Ontario L3R 9Z6, Canada  
ALPINE ELECTRONICS OF U.K., LTD.  
Fletchamstead Highway,  
Coventry CV4 9TW. U.K.  
Phone 0870-33 33 763  
ALPINE ELECTRONICS DE ESPAÑA, S.A.  
Portal de Gamarra 36, Pabellón, 32  
01013 Vitoria (Alava) - APDO 133, Spain  
Phone 945-283588  
Phone 1-800-ALPINE-1 (1-800-257-4631)  
Qingdao Dongli Xinhaiyuan  
Printing Co., Ltd.  
Designed by ALPINE Japan  
No.17, jiushuidong road,  
Qingdao, China  
Printed in China (S)  
68-00493Z17-B  
 
ENGLISH  
Contents  
Installation and Connections  
Operating Instructions  
Warning ........................................................... 11  
Caution ............................................................ 11  
Precautions ...................................................... 12  
Installation ...................................................... 13  
Connections .................................................... 16  
WARNING  
WARNING.................................................. 2  
CAUTION ................................................... 3  
PRECAUTIONS ......................................... 3  
Basic Operation  
Screen Display ON/OFF ....................................4  
Adjusting the Volume.........................................4  
Switching the Source .........................................4  
Other Useful Features  
Setup Operation .................................................5  
VISUAL EQTM Operation ..................................7  
Changing to Another Product’s Source..............8  
Operating Other Products ..................................8  
Information  
In Case of Difficulty ........................................10  
Specifications ...................................................10  
1-EN  
 
WARNING  
WARNING  
This symbol means important instructions.  
Failure to heed them can result in serious  
injury or death.  
DO NOT WATCH VIDEO WHILE DRIVING.  
Watching the video may distract the driver from looking  
ahead of the vehicle and cause an accident.  
INSTALL THE PRODUCT CORRECTLY SO THAT THE  
DRIVER CANNOT WATCH TV/VIDEO UNLESS THE  
VEHICLE IS STOPPED AND THE EMERGENCY BRAKE  
IS APPLIED.  
DO NOT OPERATE ANY FUNCTION THAT TAKES  
YOUR ATTENTION AWAY FROM SAFELY DRIVING  
YOUR VEHICLE.  
It is dangerous for the driver to watch TV/Video while  
driving a vehicle. Installing this product incorrectly  
enables the driver to watch TV/Video while driving. This  
may cause a distraction, preventing the driver from  
looking ahead, thus causing an accident. The driver or  
other people could be severely injured.  
Any function that requires your prolonged attention  
should only be performed after coming to a complete stop.  
Always stop the vehicle in a safe location before  
performing these functions. Failure to do so may result in  
an accident.  
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN  
STILL HEAR OUTSIDE NOISE WHILE DRIVING.  
Failure to do so may result in an accident.  
MINIMIZE DISPLAY VIEWING WHILE DRIVING.  
Viewing the display may distract the driver from looking  
ahead of the vehicle and cause an accident.  
DO NOT DISASSEMBLE OR ALTER.  
Doing so may result in an accident, fire or electric shock.  
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.  
Use for other than its designed application may result in  
fire, electric shock or other injury.  
KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF  
THE REACH OF CHILDREN.  
Swallowing them may result in serious injury. If  
swallowed, consult a physician immediately.  
USE THE CORRECT AMPERE RATING WHEN  
REPLACING FUSES.  
Failure to do so may result in fire or electric shock.  
2-EN  
 
PRECAUTIONS  
CAUTION  
Temperature  
This symbol means important instructions.  
Failure to heed them can result in injury or  
material property damage.  
Be sure the temperature inside the vehicle is between  
+45°C (+113°F) and 0°C (+32°F) before turning your unit  
on.  
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.  
Fuse Replacement  
Failure to do so may cause personal injury or damage to  
the product. Return it to your authorized Alpine dealer or  
the nearest Alpine Service Centre for repairing.  
When replacing the fuse(s), the replacement must be of  
the same amperage as shown on the fuse holder. If the  
fuse(s) blows more than once, carefully check all  
electrical connections for shorted circuitry. Also have your  
vehicles voltage regulator checked.  
Maintenance  
If you have problems, do not attempt to repair the unit  
yourself. Return it to your Alpine dealer or the nearest  
Alpine Service Station for servicing.  
Installation Location  
Make sure the TME-M770 will not be exposed to:  
Direct sun and heat  
High humidity  
Excessive dust  
Excessive vibrations  
After turning the system off, a slight ghost of the image  
will remain temporarily. This is an effect peculiar to  
LCD technology and is normal.  
Under cold temperature conditions, the screen may  
lose contrast temporarily. After a short warm-up  
period, it will return to normal.  
About the Touch Switch  
To protect the display, lightly touch the screen with the  
tip of your finger.  
If there is no response from the switch, then move your  
finger away from the screen and touch again.  
3-EN  
 
Basic Operation  
Switching the Source  
1
Touch the option part of the display to display  
each source operation screen or source  
selection screen.  
2
If each source operation screen is displayed,  
touch CONTROL on the upper right side of the  
screen to display the source selection screen.  
• The source selection screen is displayed by touching  
“CONTROL” as described below, depending on the  
current source.  
When touched while the current source is GAME,  
AUX 1 or AUX 2 : Source selection screen  
When touched while the current source is EXT.DVD:  
EXT.DVD operation screen Source selection  
screen  
Main power lamp  
POWER  
Illumination sensor  
(VOLUME UP)  
(VOLUME DOWN)  
When touched while the current source is TV: TV  
operation screen Source selection screen  
When touched while the current source is LINK:  
AUDIO operation screen EXT.DVD operation  
screen TV operation screen Source selection  
screen  
Screen Display ON/OFF  
1
2
Press the POWER button.  
To turn off the POWER, press the POWER  
button again.  
3
Touch the source (NAV. / AUX 1/ AUX 2) you  
want to view.  
If properly connected, the monitors main  
POWER will turn off when the vehicle's  
ignition switch is off. If the main power lamp  
illuminates in the STAND BY mode, the  
vehicle's battery may be discharged.  
After turning the system off, a slight ghost of  
the image will remain temporarily. This is an  
effect peculiar to LCD technology and is  
normal.  
CONTROL  
SOURCE  
Under cold temperature conditions, the  
screen may lose contrast temporarily. After a  
short warm-up period, it will return to normal.  
VISUAL  
EQ  
NAV.  
AUX 1  
AUX 2 SETUP  
SOURCE  
P 1/2  
• The AUX 1, AUX 2 source name changes to the  
selected mode name in the next item “SETUP  
operation” - “6External input name setting”. Also,  
“NAV.” is only displayed when “7 Navigation  
Settings” in following section, “Setup Operation”, is  
set to “ON”.  
• The operation screens for the different sources as  
well as the source selection screen turn off  
automatically if no operation is performed for 5  
seconds.  
Adjusting the Volume  
1
Adjust the volume level by pressing the  
button.  
or  
4-EN  
 
Other Useful Features  
1 Display mode selection for the display  
Setup Operation  
(DISPLAY MODE)  
1
Touch the option part of the display to display  
each source operation screen or source  
selection screen.  
Normal images are  
expanded uniformly in  
the horizontal direction  
and are displayed over  
2
If each source operation screen is displayed,  
touch CONTROL on the upper right side of the  
screen to display the source selection screen.  
the entire screen.  
WIDE  
Normal images are  
expanded in the  
horizontal direction and  
are displayed over the  
entire screen. The  
expansion ratio  
3
4
Touch SETUP.  
Select the desired setting item screen by  
ZOOM  
touching or  
.
increases towards the  
right and left edges of  
the screen.  
5
Change the setting by touching or  
.
Normal images are  
expanded in the  
SETUP  
DISPLAY MODE  
DIMMER  
WIDE  
HIGH  
horizontal and vertical  
directions. The top and  
bottom of the image are  
cut off. This mode is  
suited for 16:9 cinema  
size images.  
AUX OUT  
LINK  
SOUND OUT  
MONITOR  
CINEMA  
RETURN  
Normal image (4:3)  
NORMAL  
2 Dimmer adjustment (DIMMER)  
HIGH : The backlighting is set to the value  
adjusted at DIMMER HIGH LEVEL.  
LOW : The backlighting is set to the value  
adjusted at DIMMER LOW LEVEL.  
AUTO: Display illumination can be adjusted  
automatically depending on the  
brightness in the car. (Within the  
range of DIMMER HIGH LEVEL and  
DIMMER LOW LEVEL)  
Continued  
5-EN  
 
Other Useful Features  
3 Rear monitor select function (AUX OUT)  
9 Dimmer LOW level adjustment (DIMMER  
LOW LEVEL)  
LINK : Output the video/audio portion  
shown on the main monitor, to the  
rear monitor.  
Adjusts the LOW LEVEL (0 (MIN) to 15  
(MAX)) of the dimmer.  
AUX1 : Output the AUX1 video/audio to the  
rear monitor.  
p Touch panel adjustment (SCREEN  
AUX2 : Output the AUX2 video/audio to the  
rear monitor.  
ALIGNMENT)  
Adjust if the LCD display position and touch  
panel position do not match.  
4 Change sound output (SOUND OUT)  
: Reset to default settings.  
: Changes to adjustment screen. The  
adjustment method is as follows.  
1) Touch from SCREEN ALIGNMENT.  
The screen changes to the adjustment  
screen.  
MONITOR  
: Outputs sound through the  
built-in speakers.  
HEADPHONE : Outputs sound to  
headphones if connected.  
*Note that sound will not be output unless  
the audio output settings are appropriate.  
2) Touch the  
mark on the lower left side  
of the screen.  
The adjustment screen switches.  
5 External input sound level adjustment  
(AUX IN 1 LEVEL/AUX IN 2 LEVEL)  
3) Touch the  
mark on the upper right side  
HIGH: Sets the sound level at a high level.  
LOW : Reduces the sound level.  
of the screen.  
When the adjustment is finished, the  
screen returns to the SETUP screen.  
6 External input name setting (AUX IN 1  
MODE/AUX IN 2 MODE)  
If you touch RETURN on the adjustment screen,  
nothing is adjusted and the screen returns to the  
SETUP screen.  
Select the name from the following list, to be  
used for the product using the external input  
mode. This will apply to the touch switch  
name at source selection time and the  
source name during playback change.  
6
When the settings are completed, touch  
RETURN.  
The screen returns to the source selection  
screen.  
OFF/TV/EXT.DVD/GAME/AUX 1 (2)/LINK  
(AUX 1 MODE only)  
Set to LINKwhen the IVA-D300 series or VPE-  
S431 is connected. (Be sure to connect to the AUX  
IN 1connector.)  
Set to EXT.DVDwhen the DVA-5210 , DVA-5205  
series, DHA-S680 series or the like is connected.  
Set to TVif a TV tuner is connected to this  
product.  
The way the source operation screens and the source  
selection screen switches when CONTROLis  
touched differs according to the selected mode. (See  
page 4 Switching the Source, step 2.)  
7 Navigation settings (NAV. IN)  
When the navigation is connected, set to  
ON.  
8 Dimmer HIGH level adjustment (DIMMER  
HIGH LEVEL)  
Adjusts the HIGH LEVEL (16 (MIN) to 31  
(MAX)) of the dimmer.  
6-EN  
 
VISUAL EQTM Operation  
4 Tint tone adjustment (TINT)  
Tint tone can be adjusted from G15 (G MAX)  
to R15 (R MAX).  
*Adjustment cannot be made in the  
NAVIGATION (RGB connection) mode.  
1
Touch the option part of the display to display  
each source operation screen or source  
selection screen.  
2
If each source operation screen is displayed,  
touch CONTROL on the upper right side of the  
screen to display the source selection screen.  
5 Contrast adjustment (CONTRAST)  
Contrast can be adjusted from 15 (LOW) to  
+15 (HIGH).  
3
4
5
Touch VISUAL EQ.  
6 Screen quality adjustment (SHARP)  
Screen quality can be adjusted from 15  
(SOFT) to +15 (HARD).  
Select the desired setting by touching or  
.
Change the selected setting by touching or  
.
7 Storing (USER MEMORY)  
You can store the settings adjusted in steps  
2 to 6 in the following way.  
VISUAL EQ  
1) Touch or from USER MEMORY after  
adjusting settings 2 to 6, and select the  
preset number you want to store in  
(P.SET-1, 2).  
2) After selecting the preset No., touch  
WRITE.  
VISUAL EQ MODE  
OFF  
RETURN  
P.SET-1, 2 stored here can be accessed from  
1 VISUAL EQ mode selection.  
If 2 to 6 are adjusted, VISUAL EQ mode in 1  
changes to CUSTOM.  
1 VISUAL EQ mode (manufacturers settings)  
selection (VISUAL EQ MODE)  
OFF  
: Default setting.  
NIGHT M. : Suitable for movies with a lot of  
dark scenes.  
6
When setting is completed, touch RETURN.  
The screen changes to the source selection  
screen.  
SOFT  
: Suitable for movies with  
computer graphics or  
animation.  
SHARP  
: Suitable for old movies whose  
resolution is unclear.  
CONTRAST: Suitable for the latest movies.  
P.SET-1, 2 : Accesses the preset number  
stored in step 7 Storing.  
To return to the default values after selecting one of  
the modes between NIGHT M.and CONTRAST”  
then adjusting the image brightness, color density  
and so on to suit your tastes, set this function to  
OFF.  
2 Brightness adjustment (BRIGHT)  
Allows the brightness (15 (MIN)~+15 (MAX))  
of the picture.  
3 Color depth adjustment (COLOR)  
Change depth can be adjusted from 15  
(MIN) to +15 (MAX).  
*Adjustment cannot be made in the  
NAVIGATION (RGB connection) mode.  
7-EN  
 
Other Useful Features  
<When the AUX IN 1 connection destination is VPE-  
S431>  
Changing to Another Product’s Source  
After touching SOURCE, change the source  
with the following operation.  
1) Touch P 1/2.  
The screen changes to P 2/2.  
2) Touch “ ” “ ” “ ” “ ” to select the  
desired source. Touch ENTER.  
Touch RETURNto return to the previous  
screen.  
When used with touch panel compatible products  
such as the IVA-D300 series/VPE-S431, sources  
connected to those products are also selectable.  
1
2
3
Touch the option part of the display to display  
each source operation screen or source  
selection screen.  
If each source operation screen is displayed,  
touch CONTROL on the upper right side of the  
screen to display the source selection screen.  
When SETUPis selected, the setup operation on  
the VPE-S431 can be performed in the same way as  
the source selection operation. For details on the  
setup items, see the VPE-S431s operating  
instructions.  
Touch SOURCE.  
CONTROL  
SOURCE  
Remote Control Sensor  
VISUAL  
EQ  
NAV.  
AUX 1  
AUX 2 SETUP  
SOURCE  
P 1/2  
<When the AUX IN 1 connection destination is the  
IVA-D300 series etc.>  
Each time you touch SOURCE, the source  
changes.  
The source depends on the settings and  
connections of the product used together with  
the IVA-D300 series.  
Refer to the combined products instructions  
manuals.  
Remote sensor  
Receives the remote control signal from connected  
ALPINE products such as navigation and DVD players.  
Operating Other Products  
When the TME-M770 is used in combination with a product designed to be operated from the TME-M770  
(IVA-D300 series, DVA-5210, DHA-S680 series, etc.), some of the operations on the other product can be  
performed from the TME-M770. Below are some examples of the operations that can be performed.  
Operating a DVD in the IVA-D300 series  
1
Touch any point on the display.  
The AUDIOoperation screen appears.  
AUDIO  
CONTROL  
Change  
pages  
TOP  
MENU  
P 1/2  
ENTER RETURN  
P 2/2  
MENU  
1
2
3
4
5
6
7
8
9
p
q
w
e
8-EN  
 
Operation of DVD in IVA-D300 series  
Touch  
Long touch  
Play from start of current chapter  
Play/pause  
2x fast reverse/8x fast reverse after 5 seconds  
1
2
2x fast forward/8x fast forward after 5 seconds  
Slow play (from pause mode)  
Play next chapter  
3
PRE STOP/STOP  
ł
STOP  
4
5
6
7
8
9
p
q
w
e
Call out DVD menu  
Switch page (function guide)  
Move menu cursor  
Enter (DVD menu)  
Call out DVD top menu  
Switch page (function guide)  
Operating the DVA-5210 and the DHA-S680 series  
1
2
Touch the option part of the display.  
The screen changes to the operation screen for each source.  
Touch CONTROLon the upper right side of the screen.  
Display the EXT.DVDoperation screen.  
EXT.DVD  
CONTROL  
Change  
pages  
TOP  
MENU  
P 1/2  
ENTER RETURN  
P 2/2  
MENU  
1
2
3
4
5
6
7
8
9
p
q
w
e
Operation of a DVD player (DVA-5210)  
Operation of a DVD changer (DHA-S680 series)  
Touch  
Long touch  
Touch  
Long touch  
2x fast reverse/  
8x fast reverse after 5 seconds  
Play from start of current chapter  
Play/pause  
Play from start of current chapter  
Play  
16x fast reverse  
Slow play  
1
2
3
2x fast forward/  
8x fast forward after 5 seconds  
Slow play (from pause mode)  
Play next chapter  
Play next chapter  
16x fast forward  
PRE STOP/STOP  
PRE STOP/STOP  
Switch DISC  
Switch DISC  
STOP  
4
5
6
7
8
9
p
Call out DVD menu  
Switch page (function guide)  
Move menu cursor  
Enter (DVD menu)  
Move back 1 screen  
Call out DVD player setup screen*  
Call out DVD menu  
Switch page (function guide)  
Move menu cursor  
Enter (DVD menu)  
Move back 1 screen  
Call out DVD changer setup screen*  
q
(DVD player setup)  
*
(DVD changer setup)*  
Cue to start of chapter, track or  
elapsed time  
Switch page (function guide)  
Cue to start of chapter, track or  
elapsed time  
Switch page (function guide)  
Call out DVD top menu  
Call out DVD top menu  
w
e
* Stop mode only  
* Stop mode only  
If a TV is operated (A TV tuner is connected)  
1
2
Touch the option part of the display.  
The screen changes to the operation screen for each source.  
Touch CONTROLon the upper right side of the screen.  
Display the TVoperation screen.  
TV  
CONTROL  
TV Operation  
Touch  
Long touch  
Channel down  
Channel up  
Auto memory  
Preset channel down  
Preset channel up  
Change band  
1
2
3
4
5
6
A.MEMO  
P.DN P.UP  
BAND  
Continued  
1
2
3
4
5
6
9-EN  
 
Other Useful Features  
When connecting an IVA-D300 series to the TME-M770, be sure to connect it to the AUX IN 1connector and set the  
AUX IN MODEsetting (SETUP) to LINK.  
When connecting a DVA-5210, DHA-S680 series, etc., to the TME-M770, set the AUX IN MODEsetting (SETUP) to  
EXT.DVD.  
When connecting a TV tuner to the TME-M770, set the AUX IN MODEsetting (SETUP) to TV.  
The TME-M770 and other components connected to it can be operated with a separately sold remote control unit. For  
instructions on operations using the remote control unit, see the remote control units operating instructions. When  
operating an IVA-D300 series, see the Rear Entertainment Functionsection of the IVA-D300 seriess operating  
instructions.  
Depending on the connected component, some functions and operations may differ. Also refer to the operating  
instructions of the connected component.  
Information  
In Case of Difficulty  
Navigation screen is not displayed or navigation  
If you encounter a problem, please review the items in  
the following checklist. This guide will help you isolate  
the problem if the unit is at fault. Otherwise, make sure  
the rest of your system is properly connected or consult  
your authorized Alpine dealer.  
system’s remote controller keys do not work.  
Navigation systems power is turned off.  
- Press the ON/OFF (POWER) button on the navigation  
systems remote controller to turn the navigation  
systems power on.  
No function or display.  
Car's ignition is off.  
- Turn the ignition on.  
No fuse or blown fuse.  
- Check the cause and replace the fuse.  
Incorrect connections.  
* The fluorescent tube replacement is not free of charge  
even within the warranty period, for the tube is an article  
of consumption.  
- Check connection and remedy.  
Vehicle's battery is weak.  
- Check the voltage of vehicle's battery.  
Specifications  
MONITOR  
Unclear picture display.  
Fluorescent tube is exhausted.  
- Replace the fluorescent tube*.  
Screen Size  
6.5-type  
Display System  
Low reflection rear  
projection type TN liquid  
crystal panel  
Active matrix drive,  
normally white display  
No picture display.  
Brightness control is set for minimum brightness control.  
- Adjust the brightness.  
Incorrect setting of the VTR mode.  
- Switch to the correct mode.  
Protective circuit is on because of high temperature.  
- Wait until the temperature inside the vehicle comes  
down to the operating temperature range (45°C).  
Incorrect or open connection with the Monitor, AV  
interface unit.  
Drive System  
Number of Picture Elements 280,800 pcs. (H:1200 x  
V:234 dots)  
Effective Number of Picture Elements 99.99% or more  
Light Source  
Internal optical system (U-  
type cold cathode fluorescent  
tube)  
161 x 109 x 28.5mm  
360g  
Dimensions (W x H x D)  
Weight  
- Check the connection and remedy.  
Picture color is poor.  
Brightness/Color/Tint control are not set to the proper  
positions.  
- Check each control.  
AV Interface Unit  
Dimensions (W x H x D)  
Weight  
180 x 119 x 28.5 mm  
550g  
Spots or dotted lines/stripes appear.  
Caused by neon signs, high-voltage power lines, CB  
transmitter, other vehicle's ignition plugs, etc.  
- Change the location of your vehicle.  
Due to continuous product improvement,  
specifications and design are subject to change  
without notice.  
The LCD panel is manufactured using an extremely  
high precision manufacturing technology. Its effective  
pixel ratio is over 99.99%. This means that there is a  
possibility that 0.01% of the pixels could be either  
always ON or OFF.  
Unit does not operate.  
Monitor's power is not turned on.  
- Turn on the monitor's power.  
10-EN  
 
Installation and Connections  
Before installing or connecting the unit, please  
read the following and pages 2 and 3 of this  
manual thoroughly for proper use.  
DO NOT DAMAGE PIPE OR WIRING WHEN  
DRILLING HOLES.  
When drilling holes in the chassis for installation, take  
precautions so as not to contact, damage or obstruct pipes,  
fuel lines, tanks or electrical wiring. Failure to take such  
precautions may result in fire.  
Warning  
MAKE THE CORRECT CONNECTIONS.  
Failure to make the proper connections may result in fire  
or product damage.  
DO NOT INSTALL THE MONITOR NEAR THE  
PASSENGER SEAT AIR BAG.  
If the unit is not installed correctly the air bag may not  
function correctly and when triggered the air bag may  
cause the monitor to spring upwards causing an accident  
and injuries.  
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE  
GROUND.  
(Check with your dealer if you are not sure.) Failure to do  
so may result in fire, etc.  
BEFORE WIRING, DISCONNECT THE CABLE FROM  
THE NEGATIVE BATTERY TERMINAL.  
Failure to do so may result in electric shock or injury due  
to electrical shorts.  
Caution  
HAVE THE WIRING AND INSTALLATION DONE BY  
EXPERTS.  
The wiring and installation of this unit requires special  
technical skill and experience. To ensure safety, always  
contact the dealer where you purchased this product to  
have the work done.  
DO NOT ALLOW CABLES TO BECOME ENTANGLED  
IN SURROUNDING OBJECTS.  
Arrange wiring and cables in compliance with the manual  
to prevent obstructions when driving. Cables or wiring  
that obstruct or hang up on places such as the steering  
wheel, shift lever, brake pedals, etc. can be extremely  
hazardous.  
USE SPECIFIED ACCESSORY PARTS AND INSTALL  
THEM SECURELY.  
DO NOT SPLICE INTO ELECTRICAL CABLES.  
Never cut away cable insulation to supply power to other  
equipment. Doing so will exceed the current carrying  
capacity of the wire and result in fire or electric shock.  
Be sure to use only the specified accessory parts. Use of  
other than designated parts may damage this unit  
internally or may not securely install the unit in place.  
This may cause parts to become loose resulting in hazards  
or product failure.  
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR  
STEERING SYSTEMS TO MAKE GROUND  
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR  
CONNECTIONS.  
PINCHED BY A SHARP METAL EDGE.  
Bolts or nuts used for the brake or steering systems (or  
any other safety-related system), or tanks should NEVER  
be used for installations or ground connections. Using  
such parts could disable control of the vehicle and cause  
fire etc.  
Route the cables and wiring away from moving parts (like  
the seat rails) or sharp or pointed edges. This will prevent  
crimping and damage to the wiring. If wiring passes  
through a hole in metal, use a rubber grommet to prevent  
the wires insulation from being cut by the metal edge of  
the hole.  
KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF  
DO NOT INSTALL IN LOCATIONS WITH HIGH  
THE REACH OF CHILDREN.  
Swallowing them may result in serious injury. If  
swallowed, consult a physician immediately.  
MOISTURE OR DUST.  
Avoid installing the unit in locations with high incidence  
of moisture or dust. Moisture or dust that penetrates into  
this unit may result in product failure.  
DO NOT INSTALL IN LOCATIONS WHICH MIGHT  
HINDER VEHICLE OPERATION, SUCH AS THE  
STEERING WHEEL OR SHIFT LEVER.  
Doing so may obstruct forward vision or hamper  
movement etc. and results in serious accident.  
11-EN  
 
Installation and Connections  
Precautions  
IMPORTANT  
Please record the serial number of your unit in  
the space provided below and keep it as a  
permanent record. The serial number plate is  
located on the rear of the monitor or on the  
bottom of the AV interface unit.  
Be sure to disconnect the cable from the () battery  
post before installing your TME-M770. This will  
reduce any chance of damage to the unit in case of a  
short-circuit.  
Be sure to connect the color coded leads according to  
the diagram. Incorrect connections may cause the unit  
to malfunction or damage the vehicle's electrical  
system.  
When making connections to the cars electrical  
system, be aware of the factory installed components  
(e.g. on-board computer). Do not tap into these leads to  
provide power for this unit. When connecting the  
TME-M770 to the fuse box, make sure the fuse for the  
intended circuit of the TME-M770 has the appropriate  
amperage. Failure to do so may result in damage to the  
unit and/or the vehicle. When in doubt, consult your  
ALPINE dealer.  
SERIAL NUMBER:  
INSTALLATION DATE:  
INSTALLATION TECHNICIAN:  
PLACE OF PURCHASE:  
The TME-M770 uses female RCA-type jacks for  
connection to other units having RCA connectors. You  
may need an adaptor to connect other units. If so,  
please contact your authorized ALPINE dealer for  
assistance.  
12-EN  
 
Installation  
Installing AV Interface Unit  
Attaching with screws  
1. Place the unit on the location chosen for installa-  
tion.  
2. Mark the screw locations using the unit as a  
template.  
This Unit can be placed inside the trunk, on the  
kick panel of the front passenger's seat or  
underdash. However, to avoid unnecessary  
signal wiring, it is better to mount the Unit as  
close as possible to the Display.  
3. Drill a hole less than 3 mm in diameter.  
DO NOT MOUNT THE INTERFACE UNIT IN  
LOCATIONS EXPOSED TO MOISTURE OR  
EXTREME HEAT (such as the engine  
compartment).  
WARNING  
When you are drilling a hole in the car body,  
be careful not to damage pipes, tanks or  
electrical wiring etc.. It might cause an acci-  
dent or a fire.  
Velcro fastener Mounting:  
1. Place a Velcro fastener onto the mounting  
surface. The rough side should be facing the unit.  
2. Remove the backing to the adhesive on the  
Velcro strips. Press the unit onto the mounting  
location.  
4. Firmly attach the unit using 4 of the supplied self-  
tapping screws (M4 x 14).  
Self-tapping screws (M4 x 14)  
DISPLY OUT  
I
PHONE OUT  
I
AUX OUT  
I
VIDEO  
RGB IN  
I
L
AUDIO  
R
POWER SUPPLY  
I
DISPLY OUT  
I
AUX IN  
2
I
VIDEO  
L
PHONE OUT  
I
AUDIO  
R
TME-M770  
AUX IN  
1
AUX OUT  
I
I
VIDEO  
GB IN  
VIDEO  
TOUCH PANEL WIDE LCD MONITOR  
L
AUDIO  
R
L
AUDIO  
R
POWER SUPPLY  
I
AUX IN  
2
I
VIDEO  
L
AUDIO  
R
TME-M0  
AUX IN  
1
I
VIDEO  
TOUCH PANEL WIDE LCD MONITOR  
L
AUDIO  
R
Velcro fastener  
(included)  
13-EN  
 
Installation and Connections  
Attaching the monitor and stand  
3
Check the sticking position.  
1Temporarily fasten the stand with gum tape.  
2Loosen the adjustment screws, and adjust to a  
safe, viewable position.  
CAUTION  
Do not install the monitor near the front  
passenger seat air bag system.  
The fixed arm tilts towards the  
seat side.  
Angle  
adjustment  
screw  
<Mount it using the supplied bracket>  
When mounting with other than the attached Mounting  
Bracket, use the attached L shape bracket depending  
on usage.  
1
Remove the main unit attachment fitting.  
Pull this part to release.  
Seat side  
Front glass side  
Main unit  
Line of sight  
Main unit  
attachment fitting  
If the main unit  
Dashboard  
invades your line of  
sight then it will  
block your view.  
2
Loosen the main unit attachment fitting with a coin  
etc., slide it into the track on the rear of the main  
unit and temporarily fasten it. Then fix it to the  
stand.  
In order to use safely, attach to the following  
places.  
Stable and secure places.  
Places that will not have your view blocked by  
the main unit when driving.  
Places that you will not hit against if you lean  
forward while you wearing your seatbelt.  
Places where the main unit cannot hit against  
the steering wheel while driving.  
Be aware that if the surface of the dashboard is leather, wooden  
panel, stretched fabric or any non-resin based product, then the  
surface will be damaged when you remove the stand.  
Do not place the main unit directly in front of the air conditioner  
vents.  
Slide in an upward  
direction.  
14-EN  
 
4
5
Remove the main unit from the stand.  
Remove the mount from the stand and stick it to  
the dashboard etc..  
Remove any dirt on the place to install, using the  
supplied cloth.  
Fixing screws  
(M4 x 12 Supplied)  
If the place of  
attachment is  
curved, then  
bend this part  
to match the  
Mount  
shape.  
If the temperature in the car is low (Winter), then first  
heat up the place where you are going to stick the  
mount with a hairdryer etc.  
Do not apply force to the mount, or expose to  
humidity, within 24 hours after attaching.  
If the mount is not firmly stuck, then we recommend  
that you attach with the supplied fixing screws.  
6
Attach the main unit to the stand as shown in step  
2.  
Use the cable clamps to fix the cables.  
Before using, check that the main unit and the stand,  
and the stand and the place where it is attached to  
the car are fixed securely.  
15-EN  
 
Installation and Connections  
Connections  
Make connections correctly.  
Improper connections may cause a fire or operation failure.  
Basic connection  
e
u
i
r
y
p
9
w
t
1
q
2
3
4
5
7
6
8
o
;
a
s
d
f
16-EN  
 
When connecting to an IVA-D300 series or VPE-  
S431, use the AUX IN 1connector. When  
connecting a rear view camera, use the AUX IN 2.  
1 Parking brake lead (Yellow/Blue)  
Connect this lead to the parking brake lead  
powered when parking brake is pulled.  
2 Monitor control lead (White/Pink)  
Connect when upgrading with touch panel  
compatible products such as the IVA-D300  
series.  
To prevent external noise from entering the  
audio system.  
Locate the unit and route the leads at least  
10 cm away from the car harness.  
Keep the battery power leads as far away from  
other leads as possible.  
Connect the ground lead securely to a bare  
metal spot (remove the coating if necessary)  
of the car chassis.  
If you add an optional noise suppressor,  
connect it as far away from the unit as  
possible.Your Alpine dealer carries various  
Alpine noise suppressors, contact them for  
further information.  
34Remote control output lead (White/Brown)  
To remote control input lead of ALPINE products  
used in the system.  
5 Reverse Lead (Orange/White)  
Use only when a back-up camera is connected.  
Connect to the plus side of the cars reverse  
lamp that lights when the transmission is shifted  
into reverse (R).  
Switches the video picture to the back-up  
camera. This is linked with putting the car into  
reverse (R).  
6 ACC power lead (Red)  
To ACC power lead powered when engine key  
position is ACC.  
Your Alpine dealer knows best about noise  
prevention measures so consult your dealer for  
further information.  
7 Fuse (7.5A)  
8 Ground lead (Black)  
Connect the lead to a good chassis ground on  
the vehicle. Make sure the connection is made to  
bare metal and is securely fastened using the  
sheet metal screw provided.  
9 Brake Lamp  
p Brake Connector (Included)  
q Brake Signal Lead  
w Brake Switch  
e Headphone  
r Main monitor  
t Connection cable  
y RGB cable  
u To RGB output terminal  
i Made by Alpine navigation  
o Audio input connectors (AUX 1)  
Use these connectors to input the audio signals  
from a DVD player, video deck etc.  
; Video input connector (AUX 1)  
Use this connector to input the video signals  
from a DVD player, video deck etc.  
a Audio input connectors (AUX 2)  
Use these connectors to input the audio signals  
from a DVD player, video deck etc.  
s Video input connectors (AUX 2)  
Use this connector to input the video signals  
from a DVD player, video deck etc.  
d Audio output connectors  
Use these connectors to output audio signals to  
a rear monitor, etc.  
f Video output connector  
Use this connector to output video signals to a  
rear monitor, etc.  
17-EN  
 
System Connections  
1) 2 main units + head unit (IVA-D300 series) + expansion box (VPE-S431) + navigation (NVE-  
N099P, European customers only) + DVD changer (DHA-S680 series) + TV Tuner  
Navigation  
(NVE-N099P,  
sold separately)  
(European  
To RGB  
RGB cable  
(supplied with NVE-N099P)  
(European customers only)  
output  
terminal  
customers only)  
To RGB input  
terminal  
Head unit  
(IVA-D300 series,  
sold separately)  
To Ai-NET input  
connector  
Ai-NET cable  
To AV SELECTOR  
terminal  
To AUX OUT terminal  
AV SELECTOR cable  
(supplied with VPE-S431)  
RCA  
Extension  
cable  
To AUX IN 3 terminal  
To head unit terminal  
Ai-NET output connector (Black)  
To audio output terminal  
To AUX OUT 2 terminal  
RCA Extension cable  
RCA Extension cable  
DVD changer  
(DHA-S680 series,  
sold separately)  
Remote  
RCA Extension cable  
Remote control output  
lead (AUX1)  
control input  
lead (AUX2)  
To AUX IN 1  
terminal  
(supplied with DVD changer )  
To video output terminal  
Expansion box  
(VPE-S431,  
sold separately)  
Monitor control 2 lead  
To AUX IN 2 terminal  
To audio output terminal  
RCA Extension cable  
To AUX IN 1 terminal  
TV Tuner or VTR  
(sold separately)  
Rear monitor  
(TME-M770)  
B.BOX  
RCA Extension cable  
To video output terminal  
To AUX  
Remote control output  
OUT 1  
Remote control input lead  
lead (AUX1)  
terminal  
White/Brown  
White/Brown  
Monitor  
cable  
Rear monitor  
(TME-M770)  
Remote control output  
lead (AUX 2)  
Remote control input lead  
White/Brown  
RCA  
White/Brown  
Extension  
Remote  
control  
input lead  
(AUX 1)  
cable  
Monitor  
control 1  
lead  
Remote  
control  
output lead  
(AUX 1)  
To AUX IN 1 terminal  
Main unit B.BOX  
(TME-M770)  
Monitor  
cable  
Main unit monitor  
(TME-M770)  
18-EN  
 
2) Main unit + navigation (NVE-N099P, European customers only) + DVD player (such as  
DVA-5210)  
Navigation  
(NVE-N099P,  
To RGB  
RGB cable  
(supplied with NVE-N099P)  
(European customers only)  
sold separately)  
(European  
output  
terminal  
customers only)  
To RGB input  
terminal  
To audio output terminal  
RCA Extension cable  
DVD player  
Main unit B.BOX  
(TME-M770)  
(such as DVA-5210,  
sold separately)  
RCA Extension cable  
(supplied with DVD player)  
To AUX IN 1  
terminal  
To video output terminal  
Monitor  
cable  
Main unit monitor  
(TME-M770)  
Remote control output  
lead (AUX1)  
Remote control input lead  
White/Brown  
White/Brown  
3) Main unit and head unit (IVA-D300 series)  
Head unit  
(IVA-D300 series,  
sold separately)  
To AUX  
OUT  
terminal  
Remote  
control  
input lead  
RCA  
Extension  
cable  
Monitor  
control lead  
Remote  
control  
output lead  
(AUX1)  
To AUX IN 1 terminal  
Main unit B.BOX  
(TME-M770)  
Monitor  
cable  
Main unit monitor  
(TME-M770)  
19-EN  
 
 
R
Car Audio and Navigation Systems  
GERÄTE-PASS  
AUDIO SYSTEME  
Fahrzeugmarke:  
Typ:  
Amtl. Kennzeichen:  
Name des Halters:  
Straße:  
Wohnort:  
Bitte füllen Sie diesen Pass vollständig aus und bewahren Sie ihn  
außerhalb des Fahrzeugs auf:  
Im Falle eines Diebstahls wird für Sie die Schadensabwicklung mit der  
Versicherung einfacher, und Sie erleichtern der Polizei die Fahndung  
nach den Tätern.  
 
Händlerstemple  
Tipps der Polizei:  
[ Stellen Sie Ihr Fahrzeug stets gut sichtbar ab.  
[
Verschließen Sie Türen, Fenster, Schiebedach und Kofferraum immer, auch bei nur kurzer Abwesenheit.  
[ Lassen Sie keine Wertsachen sichtbar im Auto liegen.  
[ Wird Ihr Fahrzeug aufgebrochen, wenden Sie sich sofort an die nächste Polizeidienststelle.  
[ Belassen Sie Ihr Fahrzeug nach einem Aufbruch im Originalzustand.  
[ Informieren Sie sich über technische Sicherungsmöglichkeiten bei einer kriminalpolizeilichen  
Beratungsstelle.  
Gerät 1  
Modell-Nr.:  
Hersteller:  
Seriennummer:  
A
L
Kaufdatum:  
Preis:  
 
 
Appendix  
Product Information  
Card  
Produkt-  
Informationskarte  
Q8. Purpose of buying this  
Q8. Zweck des Kaufs dieses  
English  
Filling in this Product  
unit?  
1. Addition  
2. Replacement  
Deutsch  
Das Ausfüllen dieser  
Geräts?  
1. Zusätzlich  
2. Austausch  
Information Card is voluntary. If  
you fill in this card and send it to  
Alpine, your data will be  
tabulated into reference data for  
future Alpine product  
development. In addition, in the  
future you may receive  
information about new products  
or Survey Mail requesting  
additional opinions about Alpine  
products or services. If you  
agree to the above term, please  
sign your name in the indicated  
space and return the card. Any  
additional comments or inquiries  
may be sent to : Person in charge  
of Customer Service department  
Alpine Electronics (Europe)  
GmbH.  
Produktinformations-Karte ist  
freiwillig. Sollten Sie diese Karte  
vervollständigen, so werden die Daten  
für zukünftige Produktentwicklungen  
von Alpine als Referenzdaten  
herangezogen. Ebenso können Sie in  
der Zukunft Informationen über neue  
Alpine Produkte erhalten oder uns  
auch Ihre Meinung über Alpine  
Produkte und Dienstleistungen im  
Rahmen von Kunden-Befragungen  
mitteilen. Stimmen Sie dem Kontakt  
durch Alpine zu, so würden wir Sie  
bitten, in dem dafür vorgesehenen Feld  
zu unterschreiben und die Karte  
kostenfrei an uns zurückzuschicken.  
Zusätzliche Kommentare und  
Meinungen können Sie gerne an den  
zuständigen Kontakt im Kundendienst  
Alpine Electronics (Europe) GmbH  
senden.  
Previous brand replaced?  
Marke des ausgetauschten  
Geräts?  
1. Factory installed  
2. Alpine  
3. Other (Brand  
1. Serienmäßige Ausstattung  
2. Alpine  
3. Anderer Hersteller →  
Name)  
(Herstellername)  
Q9. Have you purchased  
Q9. War dies das erste Mal,  
Alpine products before?  
1. First time  
2. Two or More times  
Q10.When you purchased this  
dass Sie ein Alpine-Gerät  
gekauft haben?  
1. Erstes Mal  
2. Zweites Mal oder öfter  
Q10.Haben Sie dieses Alpine-  
Alpine unit, did you  
compare it with other  
Gerät vor dem Kauf mit  
Geräten anderer Hersteller  
verglichen?  
brand?  
1. Yes (Brand  
Name)  
2. No.  
Q11.GENDER  
1. Male  
2. Female  
Q12.AGE  
Q13.MARITAL STATUS  
1. Single  
1. Ja →  
(Herstellername)  
2. Nein  
Q11.Geschlecht  
1. Männlich  
2. Weiblich  
Q12.Alter  
Q13.Familienstand  
1. Ledig  
2. Verheiratet  
Q14.Beruf  
1. Selbständige/Firmeninhaber/  
freiberuflich Tätige  
2. Leitende Angestellte  
3. Sonstige Angestellte  
4. Beamte  
5. Schulbildung  
6. Studium  
7. Sonstige  
Frankfurter Ring 117, 80807  
München, Germany  
Phone: +49-(0)89-32 42 640  
Frankfurter Ring 117, 80807  
München, Germany  
Phone: 089-32 42 640  
2. Married  
Q14.OCCUPATION  
1. Company Owner/Self-  
employed/Freelance  
2. Manager  
3. Company Employee  
4. Civil Servant  
5. Educator  
6. Student  
7. Other  
Q15.Comments  
Q1. PRODUCT PURCHASED  
1. Cassette Player  
2. CD Player  
3. MD Player  
4. DVD Player  
5. CD Changer  
6. Amplifier  
7. Speaker  
8. Subwoofer  
9. Monitor Controller  
10. Video Monitor  
11. Navigation  
12. Processor/Equalizer  
13. CD/Video CD Changer  
14. Other  
Q1. gekauftes Gerät  
1. Kassetten-Spieler  
2. CD-Spieler  
3. MD-Spieler  
4. DVD-Spieler  
5. CD-Wechsler  
6. Verstärker  
7. Lautsprecher  
8. Subwoofer  
9. Monitor-Controller  
10. Video-Monitor  
11. Navigationssystem  
12. Prozessor/Equalizer  
13. CD/Video-CD-Wechsler  
14. andere  
Q15.Kommentar:  
Q2. MODEL  
NUMBER:  
Q2. Modellnummer:  
Q3. DATE OF PURCHASE:  
Q3. Kaufdatum:  
Monat:  
Month:  
Jahr:  
Year:  
Q4. If navigation system, which  
Q4. Falls Navigationssystem:  
monitor?  
1. Alpine (Model  
No.)  
Welcher Monitor?  
1. Alpine →  
(Modellnr.)  
2. Other (Brand  
Name)  
2. Anderer Hersteller →  
(Herstellername)  
Q5. Art des Geschäfts, in dem  
Q5. STORE TYPE WHERE  
PURCHASED:  
1. Car Audio Specialist  
2. Audio/Video Store  
3. Electronics/Appliance Store  
4. Car Accessories Shop  
5. Other  
Sie das Gerät gekauft  
haben:  
1. Spezialist für Auto-  
Audioanlagen  
2. Audio/Video-Geschäft  
3. Elektro-Geschäft  
4. Autozubehör-Geschäft  
5. Anderer  
Q6. Type of vehicle in which  
this unit is installed:  
Make:  
Hersteller  
Q6. Art des Fahrzeugs, in das  
Model:  
Purchased  
Year:  
Model  
das Gerät installiert wurde:  
Marke:  
Modell:  
Year:  
Q7. How was this vehicle  
gekauft im  
Jahr:  
Baujahr:  
purchased?  
1. Purchase  
2. Lease  
Q7. Wie haben Sie das  
Fahrzeug gekauft?  
1. Kauf  
2. Leasing  
 
Carte dinformations  
Tarjeta de información  
sur le produit  
del producto  
Q8. Pourquoi avez-vous acheté cet  
appareil?  
1. Addition  
Q8. ¿Propósito de comprar  
Français  
Español  
esta unidad?  
1. Mejora del sistema  
2. Sustitución  
En remplissant volontairement  
cette fiche, et en lenvoyant à  
Alpine, vous acceptez que ces  
informations soient utilisées par  
Alpine, dans le cadre de  
El envío de la información  
solicitada es voluntario. Si Vd.  
nos la remite, será utilizada de  
modo confidencial para el  
desarrollo de futuros productos  
Alpine. Si Vd. desea recibir  
información sobre nuevos  
productos de nuestra gama,  
indique su nombre en el espacio  
designado y remítanos la tarjeta.  
Cualquier solicitud adicional  
puede ser enviada a : Persona  
responsable del Servicio de  
Atención al Cliente de Alpine  
Electronics (Europe) GmbH.  
Frankfurter Ring 117, 80807  
2. Remplacement  
Marque précédente  
remplacée?  
¿Sustitución de marca anterior?  
1. Instalado en la fábrica  
2. Alpine  
1. Installée en usine  
2. Alpine  
3. Autre →  
(Marque)  
Q9. Aviez-vous déjà acheté  
des produits Alpine?  
1. Première fois  
2. Deux fois ou plus  
Q10.Lorsque vous avez acheté  
ce produit Alpine, lavez-  
vous comparé à une autre  
marque?  
1. Oui (Marque)  
2. Non  
Q11.SEXE  
1. Masculin  
2. Féminin  
Q12.AGE  
Q13.SITUATION DE FAMILLE  
1. Célibataire  
2. Marié  
Q14.PROFESSION  
1. Entrepreneur/Travailleur  
indépendant/Free-lance  
2. Directeur  
3. Employé de bureau  
4. Fonctionnaire  
5. Educateur  
6. Etudiant  
7. Autre  
Q15.Commentaires  
3. Otros  
marca)  
(Nombre de  
développement de nouveaux  
produits. Par ailleurs, vous  
autorisez Alpine à solliciter  
votre opinion par mailing sur de  
nouveaux produits ou services.  
Si vous acceptez les termes ci-  
dessus, veuillez signer cette  
carte à lendroit indiqué, et nous  
la retourner. Tout autre  
commentaire ou demande doit  
être adressé à lattention de:  
Responsable du service  
consommateur Alpine  
Electronics (Europe) GmbH.  
Frankfurter Ring 117, 80807  
Q9. ¿Ha comprado Vd.  
productos Alpine  
anteriormente?  
1. Primera vez  
2. Dos o más veces  
Q10.Cuando usted compró esta  
unidad Alpine, ¿la  
comparó con otros  
fabricantes?  
1. Si (Nombre de  
marca)  
2. No  
München, Germany  
Phone: +49-(0)89-32 42 640  
Q11.SEXO  
1. Masculino  
2. Femenino  
Q12.Edad  
Q13.Estado civil  
1. Soltero  
München, Germany  
Phone: +49-(0)89-32 42 640  
Q1. Producto Comprado  
1. Radio/Cassette  
2. Radio/CD  
3. Reproductor de MD  
4. Reproductor de DVD  
5. Cambiador de CD  
6. Amplificador  
2. Casado  
Q1. PRODUIT ACHETE  
1. Lecteur de cassette  
2. Lecteur de CD  
3. Lecteur MD  
4. Lecteur DVD  
5. Changeur de CD  
6. Amplificateur  
7. Haut-parleur  
8. Haut-parleur de graves  
9. Station Multimedia  
10. Moniteur Vidéo  
11. Navigation  
12. Processeur/Egaliseur  
13. Changeur de CD/CD Vidéo  
14. Autre  
Q14.Ocupación  
1. Propietario de empresa/  
Autónomo/Profesional  
independiente  
2. Gerente  
7. Altavoz  
8. Subwoofer  
3. Empleado de compañia  
4. Empleado público  
5. Profesor  
6. Estudiante  
7. Otros  
9. Monitor de control  
10. Monitor de video  
11. Sistema de navegación  
12. Procesador/Ecualizador  
13. Cambiador de CD/Video CD  
14. Otros  
Q15.Comentarios  
Q2. Número de  
modelo:  
Q2. NUMERO DU  
Q3. Fecha de compra:  
MODELE:  
Mes:  
Año:  
Q3. DATE DACHAT:  
Mois:  
Année:  
Q4. En caso de sistema de  
navegación, ¿qué  
Q4. Si cest un système de  
monitor?  
1. Alpine (N° de  
modelo)  
navigation, quel moniteur?  
1. Alpine (N° du  
modèle)  
2. Autre →  
(Marque)  
2. Otros  
marca)  
(Nombre de  
Q5. TIPO DE TIENDA DONDE  
Q5. TYPE DE MAGASIN OU  
COMPRÓ:  
1. Especialista en audio de  
automóviles  
2. Tienda de audio/video  
3. Tienda de electrónica/  
electrodomésticos  
4. Tienda de accesorios  
automovilísticos  
VOUS AVEZ ACHETE LE  
PRODUIT:  
1. Spécialiste autoradio  
2. Magasin audio/vidéo  
3. Magasin d’électronique/  
appareils  
4. Magasin daccessoires  
automobiles  
5. Otros  
Q6. Tipo de vehiculo en que la  
5. Autre  
Q6. Type de véhicule dans  
unidad está instalada:  
Marca:  
Modelo:  
lequel cet appareil est  
installé:  
Marque:  
Modèle:  
Année  
dachat:  
modèle:  
Año de  
compra:  
modelo:  
Año del  
Année du  
Q7. ¿Cómo fue comprado este  
vehiculo?  
1. compra  
Q7. Comment avez-vous  
acheté ce véhicule?  
1. Achat  
2. Leasing  
 
2. Location-bail  
Scheda informazioni  
prodotto  
Q8. Scopo acquisto  
1. Aggiunta  
2. Sostituzione  
Italiano  
La compilazione di questa formulario è  
volontaria. Se compilate questo  
formulario, ritornandolo ad Alpine, i  
Vostri dati saranno raccolti in un file di  
riferimento per lo sviluppo dei nuovi  
prodotti Alpine. In aggiunta Voi  
potrete ricevere in futuro informazioni  
riguardanti i nuovi prodotti o la  
richiesta di una Vostra opinione circa i  
prodotti o i servizi forniti da Alpine. Se  
siete daccordo, Vi preghiamo di  
ritornarci il formulario completato  
negli appositi spazi con i Vostri dati. In  
caso desideriate fornire altri commenti  
o richiedere informazioni aggiuntive,  
potete indirizzare il tutto a :  
Marca sostituita  
1. Installato di fabbrica  
2. Alpine  
3. Altro (Nome  
marca)  
Q9. Avevate già acquistato  
prodotti Alpine?  
1. No  
2. Due o tre volte  
Q10.Nellacquistarlo, avete  
paragonato questo  
prodotto ad unaltra  
marca?  
1. Si (Nome  
marca)  
2. No  
Responsabile dipartimento Servizio  
Clienti Alpine Electronics (Europe)  
GmbH.  
Frankfurter Ring 117, 80807 München,  
Germany  
Q11.SESSO  
1. Maschile  
2. Femminile  
Q12.ETÀ  
Q13.STATO CIVILE  
1. Celibe/nubile  
Phone: +49-(0)89-32 42 640  
2. Coniugato/coniugata  
Q14.LAVORO  
1. Proprietario di azienda/  
artigiano/libero professionista  
2. Manager  
3. Impiegato  
4. Impiegato statale  
5. Insegnante  
6. Studente  
7. Altro  
Q15.Commenti  
Q1. PRODOTTO  
ACQUISTATO  
1. Lettore di cassette  
2. Lettore CD  
3. Lettore MD  
4. Lettore DVD  
5. CD Changer  
6. Amplificatore  
7. Altoparlante  
8. Subwoofer  
9. Radio Monitor  
10. Monitor video  
11. Sistema di navigazione  
12. Processore/equalizzatore  
13. Cambia CD/Video CD  
14. Altro  
Q2. NUMERO  
MODELLO:  
Q3. DATA DI ACQUISTO:  
Mese:  
Anno:  
Q4. In caso di acquisto di un  
sistema di navigazione,  
quale monitor possiede?  
1. Alpine (No.  
Modello)  
2. Altro Nome  
marca  
Q5. NEGOZIO DI ACQUISTO:  
1. Specialista Car Stereo  
2. Negozio di audio/video  
3. Negozio di elettronica/  
elettrodomestici  
4. Negozio accessori automobile  
5. Altro  
Q6. Tipo di veicolo posseduto:  
Marca:  
Modello:  
Anno  
Anno  
acquisto:  
modello:  
Q7. Modalità acquisto  
1. Acquisto  
2. Leasing  
 
I agree to the above stated terms of the Alpine Product Information Card.  
Ich stimme dem Kontakt durch Alpine für Informations- und Befragungszwecke zu.  
Jaccepte les termes de cette carte dinformation produit Alpine.  
Estoy conforme con los términos de la tarjeta de información sobre producto de Alpine.  
Accetto i termini della scheda informazioni prodotti Alpine.  
(Date/Datum/Date/Fecha/Data)  
(Signature/Unterschrift/Signature/Firma)  
Name/Nom/Nombre/Nome  
(First Name/Vorname/Prénom/Primer nomble/Nome)  
(Surname/Familienname/Nom de famille/Apellido/Cognome)  
Home Address/Privatanschrift/Adresse/Dirección/Indirizzo  
(Street/Straße/Rue/Calle/Via) (Post Code/Postleitzahl/Code postal/Código postal/Codice postale)  
(Town/City/Stadt/Ville/Ciudad/Città) (Country/Land/Pays/País/Paese)  
Telephone Number:  
E-Mail/Correo electrónico:  
NO.  
Q1Other  
Q2  
Q6  
Month  
Year  
NO.1. Model No.  
Q3  
Q4  
NO.2. Brand Name  
Make:  
Purchased Year:  
Model:  
NO.  
Q5Other  
ModelYear:  
NO.  
1
Previous brand replaced.  
1. 2. 3.  
Brand Name  
Q7  
Q8  
2
NO.  
NO.  
1
2
Brand Name  
Q9  
Q10  
Q11  
NO.  
NO.  
NO.  
Other  
NO.  
Q12  
Q13  
Q14  
years old  
Comments  
Q15  
 
 

Abocom Switch HS2080 User Manual
Addonics Technologies Network Card WDAUSM User Manual
ADTRAN Network Card FNID User Manual
AGFA Digital Camera DC 1338i User Manual
AGFA Scanner DuoScan f40 User Manual
Aluratek Computer Drive ACUES3501000F User Manual
Axis Communications Security Camera P1354 E User Manual
Baldor Portable Generator BALDOR GENERATORS User Manual
Beckett Water Gardening Fishing Equipment FNB813 User Manual
Behringer Stereo Equalizer DEQ1024 User Manual