Apple AirPort Networks
1
Getting Started
1
AirPort offers the easiest way to provide wireless Internet
access and networking anywhere in the home, classroom,
or office.
AirPort is based on the latest Institute of Electrical and Electronics Engineers (IEEE)
802.11n draft specification and provides fast and reliable wireless networking in the
home, classroom, or small office. You can enjoy data transfer rates of up to five times
faster than data rates provided by the 802.11g standard and more than twice the
network range.
The new AirPort Extreme Base Station and the new Time Capsule are based on
simultaneous dual-band technology, so they work in both the 2.4 gigahertz (GHz)
or 5 GHz spectrum at the same time. And they are 100 percent backward-compatible,
so Mac computers and PCs that use 802.11a, 802.11b, 802.11g, or IEEE draft specification
802.11n wireless cards can connect to an AirPort wireless network. They also work
flawlessly with the AirPort Express for wireless music streaming and more. The
AirPort Extreme Base Station and Time Capsule have three additional 10/100/1000Base-
T Gigabit Ethernet ports, so you don’t need to include another router in your network.
To set up an AirPort Extreme Base Station, an AirPort Express, or a Time Capsule, you
use AirPort Utility, the easy-to-use setup and management application. AirPort Utility
has a simple user experience, with all software controls accessible from the same
application. It provides better management of several Apple wireless devices, with
client-monitoring features and logging.
If you’re using AirPort Utility version 5.4 or later, you can set up a guest network, in
both the 2.4 GHz and 5 GHz bands, so that guests can connect to the Internet using
your AirPort network, while you keep your private network secure. You can also choose
to set up guest accounts that expire, to grant temporary access to your network; you
no longer need to give your network password to visitors in your home or office.
You can even set up accounts with time constraints for the best in parental controls.
AirPort Utility supports IPv6 and Bonjour, so you can“advertise”network services such
as printing and sharing a hard disk over the Wide Area Network (WAN) port.
3
Note: When the features discussed in this document apply to the AirPort Extreme Base
Station, AirPort Express, and Time Capsule, the devices are referred to collectively as
Apple wireless devices.
With an AirPort Extreme Base Station or a Time Capsule, you can connect a USB hard
disk so that everyone on the network can back up, store, and share files. Every
Time Capsule includes an internal AirPort disk, so you don’t need to connect an
external one. If you want, you can connect additional USB disks to the USB port on
your Time Capsule. You can also connect a USB printer to the USB port on any
Apple wireless device, so that everyone on the network can access the printer or hub.
All Apple wireless devices provide strong, wireless security. They offer a built-in firewall
and support industry-standard encryption technologies. Yet the simple setup utility
and powerful access controls make it easy for authorized users to connect to the
AirPort network they create.
You can use an Apple wireless device to provide wireless Internet access and share a
single Internet connection among several computers in the following ways:
 Set up the device to act as a router and provide Internet Protocol (IP) addresses to
computers on the network using Dynamic Host Configuration Protocol (DHCP) and
Network Address Translation (NAT). When the wireless device is connected to a DSL
or cable modem that is connected to the Internet, it receives webpages and email
content from the Internet through its Internet connection, and then sends the
content to wireless-enabled computers, using the wireless network or using Ethernet
if there are computers connected to the Ethernet ports.
 Set up the Apple wireless device to act as a bridge on an existing network that
already has Internet access and a router providing IP addresses. The device passes
IP addresses and the Internet connection to AirPort or wireless-enabled computers,
or computers connected to the wireless device by Ethernet.
This document provides information about the latest AirPort Extreme Base Station,
AirPort Express, and Time Capsule, and detailed information about designing 802.11n
networks with AirPort Utility for computers using Mac OS X v10.5 or later, and
Windows Vista or Windows XP with Service Pack 2. If you’re using previous versions of
Mac OS X, or are setting up earlier versions of AirPort devices, you’ll find more
4
Chapter 1 Getting Started
You can set up an Apple wireless device and connect to the Internet wirelessly in
minutes. But because Apple wireless devices are flexible and powerful networking
products, you can also create an AirPort network that does much more. If you want to
design an AirPort network that provides Internet access to non-AirPort computers via
Ethernet, or take advantage of some of your wireless device’s more advanced features,
use this document to design and implement your network. You can find more general
wireless networking information and an overview of AirPort technology in the earlier
Note: The images of AirPort Utility in this document are from Mac OS X v10.5. If you’re
using a Windows computer, the images you see in this document may be slightly
different from what you see on your screen.
Configuring an Apple Wireless Device for Internet Access
Using AirPort Utility
Like your computer, Apple wireless devices must be set up with the appropriate
hardware and IP networking information to connect to the Internet. Install
AirPort Utility, which came on the CD with your wireless device, and use it to provide
Internet configuration information and other network settings.
AirPort Utility combines the ease of use of AirPort Setup Assistant and the power of
AirPort Admin Utility. It is installed in the Utilities folder in the Applications folder on
a Macintosh computer using Mac OS X, and in Start > All Programs > AirPort on
computers using Windows. AirPort Utility walks you through the setup process by
asking a series of questions to determine how the device’s Internet connection and
other interfaces should be set up. Enter the settings you received from your ISP or
network administrator for Ethernet, PPP over Ethernet (PPPoE), or your local area
network (LAN); give your AirPort network a name and password; set up a device as
a wireless bridge to extend the range of your existing AirPort network; and set other
options.
When you’ve finished entering the settings, AirPort Utility transfers the settings to your
wireless device. Then it connects to the Internet and shares its Internet connection with
computers that join its AirPort network.
You can also create an AirPort network that takes advantage of the more advanced
networking features of Apple wireless devices. To set more advanced AirPort options,
use AirPort Utility to manually set up your wireless device’s configuration, or make
quick adjustments to one you’ve already set up. Some of the AirPort advanced
networking features can be configured only using the manual setup features in
AirPort Utility.
Chapter 1 Getting Started
5
Set up your Apple wireless device manually using AirPort Utility when:
 You want to provide Internet access to computers that connect to the wireless device
using Ethernet
 you’ve already set up your device, but you need to change one setting, such as your
account information
 You need to configure advanced settings such as channel frequency, advanced
security options, closed networks, DHCP lease time, access control, WAN privacy,
power controls, or port mapping or other options
For instructions on using AirPort Utility to manually set up your wireless device and
network, see “Using AirPort Utility”on page 15.
You can extend the range of your network by using AirPort Utility to set up wireless
connections among several devices in your network, or to connect a device using
Ethernet to create a roaming network. For more information on extending the range of
your network, see “Connecting Additional Wireless Devices to Your AirPort Network”on
page 41.
Sharing a USB Hard Disk Connected to an AirPort Extreme
Base Station or Time Capsule
USB hard disk to it, and computers connected to the network—wired or wireless, Mac
or Windows—can share files using the hard disk. Every Time Capsule includes an
internal AirPort disk, so you don’t need to connect an external one. If you want, you can
connect additional USB disks to the USB port on your Time Capsule. See “Sharing and
Securing USB Hard Disks on Your Network”on page 54.
If you have a compatible USB printer connected to your Apple wireless device,
computers on the AirPort network can use Bonjour (Apple’s zero-configuration
networking technology) to print to the printer. For instructions about printing to a
USB printer from a computer, see “Connecting a USB Printer to an Apple Wireless
Device”on page 55.
Sharing Your Computer’s Internet Connection
If your computer is connected to the Internet, you can share your Internet connection
with other computers using Mac OS X version 10.2 or later, or Windows XP with Service
Pack 2. This is sometimes called using your computer as a software base station.
6
Chapter 1 Getting Started
You can share your Internet connection as long as your computer is connected to the
Internet. If your computer goes to sleep or is restarted, or if you lose your Internet
connection, you need to restart Internet sharing.
To start Internet sharing on a computer using Mac OS X v10.5 or later:
1 Open System Preferences and click Sharing.
2 Choose the port you want to use to share your Internet connection from the“Share
your connection using”pop-up menu.
3 Select the port you want to use to share your Internet connection in the“To computers
using”list. You can choose to share your Internet connection with AirPort-enabled
computers or computers with built-in Ethernet, for example.
4 Select Internet Sharing in the Services list.
5 If you want to share your Internet connection with computers using AirPort, click
AirPort Options to give your network a name and password.
Chapter 1 Getting Started
7
To start Internet sharing on a computer using Windows:
1 Open Control Panel from the Start menu, and then click“Network and Internet.”
2 Click“Network and Sharing Center.”
3 Click“Manage network connections”in the Tasks list.
4 Right-click the network connection you want to share, and then select Properties.
5 Click Sharing and then select“Allow other network users to connect through this
computer’s Internet connection.”
Note: If your Internet connection and your local network use the same port (built-in
Ethernet, for example), contact your ISP before you turn on Internet sharing. In some
cases (if you use a cable modem, for example) you might unintentionally affect the
network settings of other ISP customers, and your ISP might terminate your service to
prevent you from disrupting its network.
The following chapters explain AirPort security options, AirPort network design and
setup, and other advanced options.
8
Chapter 1 Getting Started
2
AirPort Security
2
This chapter provides an overview of the security features
available in AirPort.
you can enjoy peace of mind when you access the Internet, manage online financial
transactions, or send and receive email. The AirPort Extreme Base Station and
Time Capsule also include a slot for inserting a lock to deter theft.
For information and instructions for setting up these security features, see “Setting Up
the AirPort Extreme Network”on page 17.
Security for AirPort Networks at Home
Apple gives you ways to protect your wireless AirPort network as well as the data that
travels over it.
NAT Firewall
You can isolate your wireless network with firewall protection. Apple wireless devices
have a built-in Network Address Translation (NAT) firewall that creates a barrier
between your network and the Internet, protecting data from Internet-based IP attacks.
The firewall is automatically turned on when you set up the device to share a single
Internet connection. For computers with a cable or DSL modem, AirPort can actually be
safer than a wired connection.
Closed Network
Creating a closed network keeps the network name and the very existence of your
network private. Prospective users of your network must know the network name
and password to access it. Use AirPort Utility, located in the Utilities folder in the
Applications folder on a Macintosh computer using Mac OS X, or in Start > All
Programs > AirPort on a computer using Windows, to create a closed network.
9
Password Protection and Encryption
AirPort uses password protection and encryption to deliver a level of security
comparable to that of traditional wired networks. Users can be required to enter a
password to log in to the AirPort network. When transmitting data and passwords,
the wireless device uses up to 128-bit encryption, through either Wi-Fi Protected Access
(WPA), WPA2, or Wired Equivalent Privacy (WEP), to scramble data and help keep
it safe. If you’re setting up an 802.11n-based AirPort device, you can also use WEP
(Transitional Security Network) if both WEP-compatible and WPA/WPA2-compatible
computers will join your network.
Note: WPA security is available only to AirPort Extreme wireless devices; AirPort and
AirPort Extreme clients using Mac OS X 10.3 or later and AirPort 3.3 or later; and to
non-Apple clients using other 802.11 wireless adapters that support WPA. WPA2
security requires firmware version 5.6 or later for an AirPort Extreme Base Station,
firmware version 6.2 or later for an AirPort Express, firmware version 7.3 or later for a
Time Capsule, and a Macintosh computer with an AirPort Extreme wireless card using
AirPort 4.2 or later. If your computer uses Windows XP or Windows Vista, check the
documentation that came with your computer to see if your computer supports WPA2.
Security for AirPort Networks in Businesses and Classrooms
Businesses and schools need to restrict network communications to authorized users
and keep data safe from prying eyes. To meet this need, Apple wireless devices and
software provide a robust suite of security mechanisms. Use AirPort Utility to set up
these advanced security features.
Transmitter Power Control
Because radio waves travel in all directions, they can extend outside the confines of a
specific building. The Transmit Power setting in AirPort Utility lets you adjust the
transmission range of your device’s network. Only users within the network vicinity
have access to the network.
MAC Address Access Control
Every AirPort and wireless card have a unique Media Access Control (MAC) address.
For AirPort Cards and AirPort Extreme Cards, the MAC address is sometimes referred to
as the AirPort ID. Support for MAC address access control lets administrators set up a
list of MAC addresses and restrict access to the network to only those users whose MAC
addresses are in the access control list.
10
Chapter 2 AirPort Security
RADIUS Support
The Remote Authentication Dial-In User Service (RADIUS) makes securing a large
network easy. RADIUS is an access control protocol that allows a system administrator
to create a central list of the user names and passwords of computers that can access
the network. Placing this list on a centralized server allows many wireless devices to
access the list and makes it easy to update. If the MAC address of a user’s computer
(which is unique to each 802.11 wireless card) is not on your approved MAC address list,
the user cannot join your network.
Wi-Fi Protected Access (WPA) and WPA2
There has been increasing concern about the vulnerabilities of WEP. In response, the
Wi-Fi Alliance, in conjunction with the IEEE, has developed enhanced, interoperable
security standards called Wi-Fi Protected Access (WPA) and WPA2.
WPA and WPA2 use specifications that bring together standards-based, interoperable
security mechanisms that significantly increase the level of data protection and access
control for wireless LANs. WPA and WPA2 provide wireless LAN users with a high-level
assurance that their data remains protected and that only authorized network users
can access the network. A wireless network that uses WPA or WPA2 requires all
computers that access the wireless network to have WPA or WPA2 support. WPA
provides a high level of data protection and (when used in Enterprise mode) requires
user authentication.
The main standards-based technologies that constitute WPA include Temporal Key
Integrity Protocol (TKIP), 802.1X, Message Integrity Check (MIC), and Extensible
Authentication Protocol (EAP).
TKIP provides enhanced data encryption by addressing the WEP encryption
vulnerabilities, including the frequency with which keys are used to encrypt the
wireless connection. 802.1X and EAP provide the ability to authenticate a user on
the wireless network.
802.1X is a port-based network access control method for wired as well as wireless
networks. The IEEE adopted 802.1X as a standard in August 2001.
The Message Integrity Check (MIC) is designed to prevent an attacker from capturing
data packets, altering them, and resending them. The MIC provides a strong
mathematical function in which the receiver and the transmitter each compute and
then compare the MIC. If they do not match, the data is assumed to have been
tampered with and the packet is dropped. If multiple MIC failures occur, the network
may initiate countermeasures.
Chapter 2 AirPort Security
11
The EAP protocol known as TLS (Transport Layer Security) presents a user’s information
in the form of digital certificates. A user’s digital certificates can comprise user names
and passwords, smart cards, secure IDs, or any other identity credentials that the IT
administrator is comfortable using. WPA uses a wide variety of standards-based EAP
implementations, including EAP-Transport Layer Security (EAP-TLS), EAP-Tunnel
Transport Layer Security (EAP-TTLS), and Protected Extensible Authentication Protocol
(PEAP). AirPort Extreme also supports the Lightweight Extensible Authentication
Protocol (LEAP), a security protocol used by Cisco access points to dynamically assign a
different WEP key to each user. AirPort Extreme is compatible with Cisco’s LEAP security
protocol, enabling AirPort users to join Cisco-hosted wireless networks using LEAP.
In addition to TKIP, WPA2 supports the AES-CCMP encryption protocol. Based on the
very secure AES national standard cipher, combined with sophisticated cryptographic
techniques, AES-CCMP was specifically designed for wireless networks. Migrating from
WEP to WPA2 requires new firmware for the AirPort Extreme Base Station (version 5.6 or
later), and for AirPort Express (version 6.2 or later). Devices using WPA2 mode are not
backward compatible with WEP.
WPA and WPA2 have two modes:
 Personal mode, which relies on the capabilities of TKIP or AES-CCMP without
requiring an authentication server
 Enterprise mode, which uses a separate server, such as a RADIUS server, for user
authentication
WPA and WPA2 Personal
 For home or Small Office/Home Office (SOHO) networks, WPA and WPA2 operates in
Personal mode, taking into account that the typical household or small office does
not have an authentication server. Instead of authenticating with a RADIUS server,
users manually enter a password to log in to the wireless network. When a user
enters the password correctly, the wireless device starts the encryption process using
TKIP or AES-CCMP. TKIP or AES-CCMP takes the original password and derives
encryption keys mathematically from the network password. The encryption key is
regularly changed and rotated so that the same encryption key is never used twice.
Other than entering the network password, the user isn’t required to do anything to
make WPA or WPA2 Personal work in the home.
12
Chapter 2 AirPort Security
WPA and WPA2 Enterprise
WPA is a subset of the draft IEEE 802.11i standard and effectively addresses the wireless
local area network (WLAN) security requirements for the enterprise. WPA2 is a full
implementation of the ratified IEEE 802.11i standard. In an enterprise with IT resources,
provide centralized access control and management. With this implementation in
place, the need for add-on solutions such as virtual private networks (VPNs) may be
eliminated, at least for securing wireless connections in a network.
For more information about setting up a WPA or WPA2 protected network, see
“Using Wi-Fi Protected Access”on page 45.
Chapter 2 AirPort Security
13
3
AirPort Network Designs
3
This chapter provides overview information and instructions
for the types of AirPort Extreme networks you can set up, and
some of the advanced options of AirPort Extreme.
Use this chapter to design and set up your AirPort Extreme network.
Configuring your Apple wireless device to implement a network design requires
three steps:
Step 1: Setting Up the AirPort Extreme Network
Computers communicate with the wireless device over the AirPort wireless network.
When you set up the AirPort network created by the wireless device, you can name the
wireless network, assign a password that will be needed to join the wireless network,
and set other options.
Step 2: Configuring and Sharing Internet Access
When computers access the Internet through the AirPort Extreme network, the wireless
device connects to the Internet and transmits information to the computers over the
AirPort Extreme network. You provide the wireless device with settings appropriate for
your ISP and configure how the device shares this connection with other computers.
Step 3: Setting Advanced Options
These settings are optional for most users. They include using the Apple wireless device
as a bridge between your AirPort Extreme network and an Ethernet network, setting
advanced security options, extending the AirPort network to other wireless devices,
and fine-tuning other settings.
For specific instructions on all these steps, refer to the sections later in this chapter.
You can do most of your setup and configuration tasks using AirPort Utility, and
following the onscreen instructions to enter your ISP and network information. To set
advanced options, you need to use AirPort Utility to manually set up your Apple
wireless device and AirPort network.
14
Using AirPort Utility
To set up and configure your computer or Apple wireless device to use AirPort Extreme
for basic wireless networking and Internet access, use AirPort Utility and answer
a series of questions about your Internet settings and how you would like to set up
your network.
1 Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac,
or in Start > All Programs > AirPort on a Windows computer.
2 Select your device in the list on the left if there is more than one device in your
network. Click Continue, and then follow the onscreen instructions to enter the settings
from your ISP or network administrator for the type of network you want to set up. See
the network diagrams later in this chapter for the types of networks you can set up
using AirPort Utility.
To set up a more complicated network, or to make adjustments to a network you’ve
already set up, use the manual setup features in AirPort Utility.
Setting AirPort preferences
Use AirPort preferences to set up your wireless device to alert you when there are
updates available for your device. You can also set it up to notify you if there are
problems detected, and to provide instructions to help solve the problems.
To set AirPort preferences:
1 Open AirPort Utility, located in the Utilities folder inside the Applications folder on
a Mac, and in Start > All Programs > AirPort on a Windows computer.
2 Do one of the following:
 On a Mac, choose AirPort Utility > Preferences
 On a Windows computer, choose File > Preferences
Chapter 3 AirPort Network Designs
15
Select from the following checkboxes:
 Select“Check for Updates when opening AirPort Utility”to automatically check the
Apple website for software and firmware updates each time you open AirPort Utility.
 Select the“Check for updates”checkbox, and then choose a time interval from the
pop-up menu, such as weekly, to check for software and firmware updates in the
background. AirPort Utility opens if updates are available.
 Select“Monitor Apple wireless devices for problems”to investigate problems that
may cause the device’s status light to blink amber. With the checkbox selected,
AirPort Utility opens if a problem is detected, and then provides instructions to help
resolve the problem. This option monitors all of the wireless devices on the network.
 Select“Only Apple wireless devices that I have configured”to monitor only the
devices you’ve set up using this computer.
Monitoring devices for problems requires an AirPort wireless device that supports
firmware version 7.0 or later.
To set up your wireless device manually:
1 Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac, or
in Start > All Programs > AirPort on a Windows computer.
2 Select your device in the list.
3 Choose Base Station > Manual Setup and enter the password if necessary. The default
device password is public.
If you don’t see your wireless device in the list:
1 Open the AirPort status menu in the menu bar on a Mac and make sure that you’ve
joined the AirPort network created by your wireless device. On a Windows computer,
hover the cursor over the wireless network icon in the status tray to make sure the
computer is connected to the correct network.
The default network name for an Apple wireless device is AirPort Network XXXXXX,
where XXXXXX is replaced with the last six digits of the AirPort ID, (or MAC address).
The AirPort ID is printed on the bottom of Apple wireless devices.
2 Make sure your computer’s network and TCP/IP settings are configured properly.
On a computer using Mac OS X, choose AirPort from the Show pop-up menu in the
Network pane of System Preferences. Then choose Using DHCP from the Configure IPv4
pop-up menu in the TCP/IP pane.
On a computer using Windows, right-click the wireless connection icon that displays
the AirPort network, and choose Status. Click Properties, select Internet Protocol
(TCP/IP), and then click Properties. Make sure“Obtain an IP address automatically”is
selected.
16
Chapter 3 AirPort Network Designs
If you can’t open the wireless device settings:
1 Make sure your network and TCP/IP settings are configured properly.
On a computer using Mac OS X, select AirPort from the network connection services list
in the Network pane of System Preferences. Click Advanced, and then choose Using
DHCP from the Configure IPv4 pop-up menu in the TCP/IP pane.
On a computer using Windows, right-click the wireless connection icon that displays
the AirPort network, and choose Status. Click Properties, select Internet Protocol
(TCP/IP), and then click Properties. Make sure “Obtain an IP address automatically”
is selected.
2 Make sure you entered the wireless device password correctly. The default password
is public. If you’ve forgotten the device password, you can reset it to public by resetting
the device.
To temporarily reset the device password to public, hold down the reset button for one
second. To reset the device back to its default settings, hold the reset button for five full
seconds.
If you’re on an Ethernet network that has other devices, or you’re using Ethernet to
connect to the device:
AirPort Utility scans the Ethernet network to create the list of devices. As a result, when
you open AirPort Utility, you may see devices that you cannot configure.
Setting Up the AirPort Extreme Network
The first step in configuring your Apple wireless device is setting up the device and the
network it will create. You can set up most features using AirPort Utility and following
the onscreen instructions to enter the information from your ISP or network
administrator.
To configure a network manually or set advanced options, open your wireless device’s
configuration in AirPort Utility and manually set up your device and network.
1 Choose the network of the wireless device you want to configure from the AirPort
status menu on a computer using Mac OS X, or from the wireless connection icon in
the status tray on a computer using Windows.
2 Open AirPort Utility and select the wireless device from the list. If you don’t see the
device you want to configure, click Rescan to scan for available wireless devices, and
then select the one you want from the list.
Chapter 3 AirPort Network Designs
17
3 Choose Base Station > Manual Setup and enter the password if necessary. The default
device password is public.
You can also double-click the name of the wireless device to open its configuration in
a separate window. When you open the manual setup window, the Summary pane is
displayed. The summary pane provides information and status about your wireless
device and network.
18
Chapter 3 AirPort Network Designs
If the wireless device reports a problem, the status icon turns yellow. Click Base Station
Status to display the problem and suggestions to resolve it.
Wireless Device Settings
Click the AirPort button, and then click Base Station or Time Capsule, depending on the
device you’re setting up, to enter information about the wireless device.
Give the Device a Name
Give the device an easily identifiable name. This makes it easy for administrators
to locate a specific device on an Ethernet network with several devices.
Change the Device Password
The device password protects its configuration so that only the administrator can
modify it. The default password is public. It is a good idea to change the device
password to prevent unauthorized changes to it.
If the password is not changed from public, you’ll not be prompted for a password
when you select it from the list and click Configure.
Other Information
 Allow configuration over the WAN port. This allows you to administer the wireless
device remotely.
 Advertise the wireless device over the Internet using Bonjour. If you have an account
with a dynamic DNS service, you can connect to it over the Internet.
 Set the device time automatically. If you have access to a Network Time Protocol
server, whether on your network or on the Internet, choose it from the pop-up menu.
This ensures your wireless device is set to the correct time.
Chapter 3 AirPort Network Designs
19
Set Device Options
Click Base Station Options and set the following:
 Enter a contact name and location for the wireless device. The name and location are
included in some logs the device generates. The contact and location fields may be
helpful if you’ve more than one wireless device on your network.
 Set status light behavior to either Always On or Flash On Activity. If you choose Flash
On Activity, the device status light blinks when there is network traffic.
 If your wireless device supports it, select“Check for firmware updates”and choose an
increment, such as Daily from the pop-up menu.
Wireless Network Settings
Click Wireless, and enter the network name, radio mode, and other wireless
information.
Setting the Wireless Mode
AirPort Extreme supports two wireless modes:
 Create a wireless network. Choose this option if you’re creating a new
AirPort Extreme network.
 Extend a wireless network. Choose this option if you plan to connect another Apple
wireless device to the network you’re setting up.
Naming the AirPort Extreme Network
Give your AirPort network a name. This name appears in the AirPort status menu on the
AirPort-enabled computers that are in range of your AirPort network.
20
Chapter 3 AirPort Network Designs
Choosing the Radio Mode
Choose 802.11a/n - 802.11b/g from the Radio Mode pop-up menu if computers with
802.11a, 802.11n, 802.11g, or 802.11b wireless cards will join the network. Each client
computer will connect to the network and transmit network traffic at the highest
possible speed.
Choose 802.11n - 802.11b/g if only computers with 802.11n, 802.11b, or 802.11g
compatible wireless cards will join the network.
Note: If you don’t want to use an 802.11n radio mode, hold down the Option key and
chose a radio mode that doesn’t include 802.11n.
Changing the Channel
The “channel” is the radio frequency over which your wireless device communicates.
If you use only one device (for example, at home), you probably won’t need to change
the channel frequency. If you set up several wireless devices in a school or office,
use different channel frequencies for devices that are within approximately 150 feet of
each other.
Adjacent wireless devices should have at least 4 channels between their channel
frequencies. So if device A is set to channel 1, device B should be set to channel 6 or 11.
For best results, use channels 1, 6, or 11 when operating your device in the 2.4 GHz
range.
Choose Manually from the Radio Channel Selection pop-up menu, and then click Edit
to set the channels manually.
AirPort-enabled computers automatically tune to the channel frequency your wireless
device is using when they join the AirPort network. If you change the channel
frequency, AirPort client computers do not need to make any changes.
Password-protect Your Network
options. In the AirPort pane of AirPort Utility, click Wireless and choose one of the
following options from the Wireless Security pop-up menu:
 None: Choosing this option turns off all password protection for the network. Any
computer with a wireless adapter or card can join the network, unless the network is
set up to use access control. See “Setting Up Access Control”on page 47.
 WEP: If your device supports it, choose this option and enter a password to protect
your network with a Wired Equivalent Privacy (WEP) password. Your Apple wireless
device supports 40-bit and 128-bit encryption. To use 40-bit WEP, don’t use an
802.11n radio mode.
Chapter 3 AirPort Network Designs
21
 WPA/WPA2 Personal: Choose this option to protect your network with Wi-Fi
Protected Access. You can use a password between 8 and 63 ASCII characters or a
Pre-Shared Key of exactly 64 hexadecimal characters. Computers that support WPA
and computers that support WPA2 can join the network. Choose WPA2 Personal if
you want only computers that support WPA2 to join your network.
 WPA/WPA2 Enterprise: Choose this option if you’re setting up a network that
includes an authentication server, such as a RADIUS server, with individual user
accounts. Enter the IP address and port number for the primary and optional
secondary server, and enter a“shared secret,”which is the password for the server.
Choose WPA2 Enterprise if you want only computers that support WPA2 to join the
network.
 WEP (Transitional Security Network): If your device supports it, you can use this
option to allow computers using WPA or WPA2 to join the network. Computers or
supports 128-bit encryption. To use this option, the wireless device use an 802.11n
radio mode. Hold the Option key on your keyboard while clicking the Wireless
Security pop-up menu to use WEP (Transitional Security Netowrk).
For more information and instructions for setting up WPA or WPA2 on your network,
see “Using Wi-Fi Protected Access”on page 45.
Setting Wireless Options
Click Wireless Options to set additional options for your network.
22
Chapter 3 AirPort Network Designs
Setting Additional Wireless Options
Use the Wireless Options pane to set the following:
 5 GHz network name: Provide a name for the 5 GHz segment of the dual-band
network if you want it to have a different name than the 2.4 GHz network.
 Country: Choose the country for the location of your network from the Country
pop-up menu.
 Multicast rate: Choose a multicast rate from the pop-up menu. If you set the
multicast rate high, only clients on the network that are within range and can
achieve the speed you set will receive transmissions.
 Transmit power: Choose a setting from the Transmit Power pop-up menu to set the
network range (the lower the percentage, the shorter the network range).
 WPA Group Key Timeout: Enter a number in the text field, and choose an increment
from the pop-up menu to change the frequency of key rotation.
 Use Wide Channels: If you set up your network to use the 5 GHz frequency range,
you can use wide channels to provide higher network throughput.
Note: Using wide channels is not permitted in some countries.
network so that users must enter the exact network name and password to join
the AirPort Extreme network.
 Use interference robustness: Interference robustness can solve interference
problems caused by other devices or networks.
To set more advanced security options, see “Keeping Your Network Secure”on page 45.
Chapter 3 AirPort Network Designs
23
Setting up a Guest Network
Click Guest Network and then enter the network name and other options for the guest
network. When you set up a guest network, a portion of your connection to the
Internet is reserved for“guests”, wireless clients that can join the guest network and
connect to the Internet without accessing your private network.
Select“Allow guest network clients to communicate with each other”to allow client
computers to share files and services with each other while they’re connected to the
guest network. Make sure sharing services are set up on the client computers.
Configuring and Sharing Internet Access
The next step is setting up your wireless device’s Internet connection and sharing its
Internet access with client computers. The following sections tell you what to do,
depending on how your device connects to the Internet.
You’re Using a DSL or Cable Modem
In most cases, you can implement this network design using AirPort Utility and
following the onscreen instructions to set up your wireless device and network. You
need to use AirPort Utility to manually set up your device only if you want to set up
or adjust optional advanced settings.
24
Chapter 3 AirPort Network Designs
What It Looks Like
to Ethernet port
Time Capsule
2.4 or 5 GHz
Ethernet WAN port
DSL or cable modem
<
to Internet
How It Works
 The Apple wireless device (in this example, a Time Capsule) connects to the Internet
through its Internet WAN (<) connection to your DSL or cable modem.
 Computers using AirPort or computers connected to the wireless device’s Ethernet
LAN port (G) connect to the Internet through the device.
 The device is set up to use a single, public IP address to connect to the Internet, and
uses DHCP and NAT to share the Internet connection with computers on the network
using private IP addresses.
 AirPort computers and Ethernet computers communicate with one another through
the wireless device.
Important: Connect Ethernet computers that are not connected to the Internet to
the device’s LAN port (G) only. Since the device can provide network services, you
must set it up carefully to avoid interfering with other services on your Ethernet
network.
What You Need for a DSL or Cable Modem Connection
Components
Check
Comments
Internet account with DSL or
cable modem service provider
Does your service provider use a You can get this information
static IP or DHCP configuration? from your service provider or the
Network preferences pane on
the computer you use to access
the Internet through this service
provider.
Apple wireless device (an AirPort
Extreme Base Station, an AirPort
Express, or a Time Capsule)
Place the device near your DSL
or cable modem.
Chapter 3 AirPort Network Designs
25
What to Do
If you’re using AirPort Utility to assist you with configuring the Apple wireless device
for Internet access:
1 Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac,
or in Start > All Programs > AirPort on a Windows computer.
2 Follow the onscreen instructions and enter the settings you received from your service
provider to connect to the Internet, and then set up the device to share the Internet
connection with computers on the network.
If you’re using AirPort Utility to manually set up your wireless device:
1 Make sure that your DSL or cable modem is connected to the Ethernet WAN port (<)
on your Apple wireless device.
2 Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac,
or in Start > All Programs > AirPort on a Windows computer. Select your wireless device
and choose Base Station > Manual Setup, or double-click your device’s icon in the list to
open the configuration in a separate window.
3 Click the Internet button. Click Internet Connection and choose Ethernet or PPPoE from
the Connect Using pop-up menu, depending on which one your service provider
requires. If your service provider gave you PPPoE connection software, such as EnterNet
or MacPoET, choose PPPoE.
Note: If you’re connecting to the Internet through a router using PPPoE and your Apple
wireless device is connected to the router via Ethernet, you do not need to use PPPoE
on your wireless device. Choose Ethernet from the Connect Using pop-up menu in the
Internet pane, and deselect the“Distribute IP addresses”checkbox in the Network
pane. Contact your service provider if you aren’t sure which one to select.
4 Choose Manually or Using DHCP from the Configure IPv4 pop-up menu if you chose
Ethernet from the Connect Using pop-up menu, depending on how your service
provider provides IP addresses.
 If your provider gave you an IP address and other numbers with your subscription,
use that information to configure the wireless device IP address manually. If you
aren’t sure, ask your service provider. Enter the IP address information in the fields
below the Configure IPv4 pop-up menu.
26
Chapter 3 AirPort Network Designs
 If you chose PPPoE, your ISP provides your IP address automatically using DHCP.
Contact your service
provider for the
information you should
enter in these fields.
Use this pop-up menu
if you need to adjust
the speed of the
Ethernet WAN port.
If your service provider asks you for the MAC address of your wireless device, use the
address of the Ethernet WAN port (<), printed on the label on the bottom of the
device.
If you’ve already used AirPort Utility to set up your wireless device, the fields below the
Configure IPv4 pop-up menu may already contain the information appropriate for your
service provider.
You can change the WAN Ethernet speed if you have specific requirements for the
network you’re connected to. In most cases, the settings that are configured
automatically are correct. Your service provider should be able to tell you if you need
to adjust these settings.
Changing the WAN Ethernet speed can affect the way the wireless device interacts with
the Internet. Unless your service provider has given you specific settings, use the
automatic settings. Entering the wrong settings can affect network performance.
Chapter 3 AirPort Network Designs
27
If you configure TCP/IP using DHCP, choose Using DHCP from the Configure IPv4
pop-up menu. Your IP information is provided automatically by your ISP using DHCP.
Your service provider
may require you to
enter information
in these fields.
5 If you chose PPPoE from the Connect Using pop-up menu, enter the PPPoE settings
your service provider gave you. Leave the Service Name field blank unless your service
provider requires a service name.
Note: With AirPort, you don’t need to use a third-party PPPoE connection application.
You can connect to the Internet using AirPort.
Contact your
service provider
for the information
you should enter
in these fields.
28
Chapter 3 AirPort Network Designs
If you’re connecting to the Internet through a router that uses PPPoE to connect to the
Internet, and your wireless device is connected to the router via Ethernet, you do not
need to use PPPoE on your device. Choose Ethernet from the Connect Using pop-up
menu in the Internet pane, and deselect the“Distribute IP addresses”checkbox in the
Network pane. Because your router is distributing IP addresses, your wireless device
doesn’t need to. More than one device on a network providing IP addresses can cause
problems.
6 Click PPPoE to set PPPoE options for your connection.
 Choose Always On, Automatic, or Manual, depending on how you want to control
when your wireless device is connected to the Internet.
If you choose Always On, your device stays connected to your modem and the
Internet as long as the modem is turned on. If you choose Automatic, the wireless
device connects to the modem, which connects to the Internet when you use an
application that requires an Internet connection, such as email or an instant message
or web application. If you choose Manual, you need to connect the modem to the
Internet when you use an application that requires an Internet connection.
If you chose Automatic or Manual from the Connection pop-up menu, you need to
choose an increment, such as“10 minutes,”from the“Disconnect if idle”pop-up
menu. If you don’t use an Internet application after the increment of time has passed,
you’ll be disconnected from the Internet.
Note: If your wireless device is connected to your modem using an Ethernet LAN
port, and your modem is connected to the Internet using PPPoE, you may not be
able to use the manual setting.
Chapter 3 AirPort Network Designs
29
 Enter Domain Name System (DNS) server addresses and a specific domain name your
wireless device accesses when you connect to the Internet.
7 Click the Network button and configure how the device will share its Internet access
with AirPort and Ethernet computers.
If you chose Ethernet from the Connect Using pop-up menu, choose how your device
will share the Internet connection from the Connection Sharing pop-up menu.
 To share a single Internet connection with AirPort computers and computers
connected to the device with Ethernet using DHCP and NAT, choose“Share a public
IP address”from the Connection Sharing pop-up menu. Using DHCP and NAT lets the
wireless device dynamically and automatically assign IP addresses to client
computers, which simplifies each computer’s TCP/IP configuration. See “Setting
DHCP and NAT Options”on page 31.
By default, the wireless device allows other devices, computers using Ethernet, and
AppleTalk. If you want to connect an AppleTalk Ethernet printer to the Apple wireless
device or use AppleTalk between wired and wireless computers, make sure the
devices are connected to the Ethernet LAN port (G) on the device.
 To distribute a range of IP addresses using only DHCP, choose“Distribute a range of
IP addresses.”See “Setting DHCP Only Options”on page 33.
30
Chapter 3 AirPort Network Designs
 If you don’t want your wireless device to share its IP address, choose“Off (Bridge
Mode).”If you set up your device in bridge mode, AirPort computers have access to
all services on the Ethernet network, and the device does not provide Internet
sharing services. See “You’re Using an Existing Ethernet Network”on page 37 for
more information about setting up your wireless device as a bridge.
Using the wireless device as a bridge can be a way to address incompatibilities
between the device’s Internet sharing features and your ISP’s connection method.
Setting DHCP and NAT Options
If you chose“Share a public IP address”from the Connection Sharing pop-up menu,
you can set DHCP and NAT options. Click DHCP.
 Choose a range of IP addresses from the DHCP Range pop-up menu. Choose 10.0,
192.168, or 172.16 and then enter a beginning and ending address in the DHCP
Beginning Address and the DHCP Ending Address fields, depending on which
addresses you want the wireless device to provide.
 Enter a number in the DHCP Lease field, and then choose minutes, hours, or days
from the pop-up menu.
 Type a welcome message in the DHCP Message field. This message is displayed when
a computer joins your network.
 If your network is set up to use a Lightweight Directory Access Protocol (LDAP) server
on your network, you can enter the address of the server in the LDAP Server field,
and computers on your network will have access to it.
Chapter 3 AirPort Network Designs
31
 To provide specific IP addresses to specific computers on your wireless network,
click the Add (+) button below the DHCP Reservations list, and follow the onscreen
instructions to name the reservation and reserve the address by MAC address or
DHCP client ID. If you choose MAC address, click Continue and enter the MAC
address and specific IP address.
Next you can set NAT options for the network. Click NAT.
 You can set up a default host on your network. A default host (sometimes known as
a DMZ) is a computer on your network that is exposed to the Internet and receives
all inbound traffic. A default host may be useful if you use a computer on your
AirPort network to play network games, or want to route all Internet traffic through
a single computer.
 You can set up NAT Port Mapping Protocol (NAT-PMP). NAT-PMP is an Internet
Engineering Task Force Internet Draft, an alternative to the more common Universal
Plug and Play (UPnP) protocol implemented in many network address translation
(NAT) routers. NAT-PMP allows a computer in a private network (behind a NAT router)
to automatically configure the router to allow parties outside the private network to
contact this computer.
Included in the protocol is a method for retrieving the public IP address of a NAT
gateway, allowing a client to make this public IP address and port number known to
peers that may wish to communicate with it. This protocol is implemented in current
Apple products, including Mac OS X 10.4 Tiger and later, AirPort Extreme, AirPort
Express, and Time Capsule networking products, and Bonjour for Windows.
32
Chapter 3 AirPort Network Designs
You can also set up port mapping. To ensure that requests are properly routed to your
web, AppleShare, or FTP server, or a specific computer on your network, you need to
establish a permanent IP address for the server or computer, and provide“inbound port
mapping”information to the Apple wireless device. See “Directing Network Traffic to a
Specific Computer on Your Network (Port Mapping)”on page 49.
Setting DHCP Only Options
If you chose“Distribute a range of IP addresses”from the Connection Sharing pop-up
menu, your wireless device is set up to use DHCP to distribute a range of IP addresses
using only DHCP. You cannot use NAT if you chose this option. Click DHCP and enter
the beginning and ending addresses you want to distribute to computers joining your
wireless network.
You can set the additional DHCP options, such as DHCP Lease, DHCP Message, and
other options following the instructions above.
Setting Up Client Computers
To configure TCP/IP on client computers using Mac OS X v10.5:
1 Open System Preferences on the client computer and then click Network.
2 Do one of the following:
a If the client computer is using AirPort, select AirPort in the network connection
services list, and then click Advanced.
Chapter 3 AirPort Network Designs
33
Next, choose DHCP from the Configure IPv4 pop-up menu.
b If you enabled a DHCP server when you set up the wireless device’s network, and the
client computer is using Ethernet, select Ethernet in the network connection services
list, and then choose Using DHCP from the Configure pop-up menu.
34
Chapter 3 AirPort Network Designs
c If you selected“Distribute a range of IP addresses”when you set up the wireless
device’s network, you can provide Internet access to client computers using
Ethernet by setting the client IP addresses manually. Select Ethernet in the
network connection services list, and then choose Manually from the Configure
pop-up menu.
Enter the IP and router
addresses from the range
your device is providing.
Enter the DNS and Search
Domain addresses if
necessary.
When you configure Ethernet clients manually for a wireless device that provides
NAT over Ethernet, you can use IP addresses in the range 10.0.1.2 to 10.0.1.200.
In the Subnet Mask field, enter 255.255.255.0. In the Router field, enter 10.0.1.1.
Enter the same name server address and search domain information that you
entered in the wireless device configuration.
To configure TCP/IP on client computers using Windows
Make sure you’ve installed the wireless adapter in your computer and the software
necessary to set up the adapter.
To configure TCP/IP on client computers:
1 Open Control Panel from the Start menu, and then click“Network and Internet.”
2 Click“Network and Sharing Center.”
3 Click“Manage network connections”in the Tasks list.
4 Right-click the wireless connection you want to share, and then select Properties.
Chapter 3 AirPort Network Designs
35
5 Click Internet Protocol Version 4 (TCP/IPv4), and then click Properties.
 If you chose “Share a public IP address” in the Network pane of AirPort Utility, select
“Obtain an IP address automatically.”
 If you chose “Distribute a range of IP addresses” when you set up the wireless device’s
network, you can provide Internet access to client computers by setting the client IP
addresses manually. Select“Use the following IP address.”
When you configure clients manually for a wireless device that provides NAT service,
use IP addresses in the range 10.0.1.2 to 10.0.1.200, 172.16.1.2 to 172.16.1.200, or
192.168.1.2 to 192.168.1.200.
In the“Subnet mask”field, enter 255.255.255.0. In the“Default gateway”field, enter
10.0.1.1, 172.16.1.1, or 192.168.1.1, depending on which addressing scheme you used. Enter
the same name server address and search domain information that you entered in the
wireless device configuration.
36
Chapter 3 AirPort Network Designs
You’re Using an Existing Ethernet Network
You can use AirPort Utility to easily set up the Apple wireless device for Internet access
through an existing Ethernet network that already has a router, switch, or other
network device providing IP addresses. Use the manual setup features of AirPort Utility
if you need to adjust optional advanced settings.
What It Looks Like
to Ethernet port
2.4 or 5 GHz
Time Capsule
Router
Ethernet WAN port
<
to Internet
How It Works
 The Apple wireless device (in this example, a Time Capsule) uses your Ethernet
network to communicate with the Internet through the Ethernet WAN port (<).
 AirPort and Ethernet clients access the Internet and the Ethernet network through
the Apple wireless device.
What You Need for an Ethernet Connection
Components
Comments
Apple wireless device (an AirPort
Extreme Base Station, an AirPort
Express, or a Time Capsule)
Set the device up in bridge
mode.
Ethernet router, switch, or other
network device
The router, switch, or other
network device is set up to
provide IP addresses to
computers and devices on the
Ethernet network.
Ethernet cables
Chapter 3 AirPort Network Designs
37
What to Do
If you’re using AirPort Utility to help you set up an Apple wireless device on an
existing Ethernet network:
1 Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac,
or in Start > All Programs > AirPort on a Windows computer.
2 Click Continue and follow the onscreen instructions to connect to your local area
network (LAN).
If you’re using AirPort Utility to manually set up your wireless device:
1 Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac,
or in Start > All Programs > AirPort on a Windows computer.
2 Select your device and choose Base Station > Manual Setup, or double-click your
device icon to open the configuration in a separate window.
3 Click Internet and choose Ethernet from the Connect Using pop-up menu.
4 Choose Manually or Using DHCP from the Configure IPv4 pop-up menu, depending
on how IP addresses are provided on your Ethernet network. If you aren’t sure, ask your
service provider or network administrator.
If your addresses are provided manually, choose Manually from the Configure IPv4
pop-up menu. Enter your IP address information in the fields below the Configure
IPv4 pop-up menu.
Contact your network
administrator for the
information you should
enter in these fields.
If you’ve already used AirPort Utility to set up your Apple wireless device, the
fields below the Configure IPv4 pop-up menu may already contain the appropriate
information.
38
Chapter 3 AirPort Network Designs
If your IP address is provided by DHCP, choose Using DHCP from the Configure IPv4
pop-up menu.
5 Choose Off (Bridge Mode) from the Connection Sharing pop-up menu. Your wireless
device“bridges”the Ethernet networks Internet connection to computers connected to
the device wirelessly or by Ethernet.
See “Setting Up Client Computers”on page 33 for information about how to set up
client computers to connect to the Ethernet network.
Chapter 3 AirPort Network Designs
39
Connecting Additional Devices to Your AirPort Extreme Network
Connect a USB printer to the USB port of your Apple wireless device (in this example,
a Time Capsule) and everyone on the network can print to it. Connect a USB hub to the
USB port of an AirPort Extreme Base Station or a Time Capsule, and then connect a
hard disk and a printer so everyone on the network can access them.
If you connect a Time Capsule, you can use Time Machine in Mac OS X Leopard (v10.5.2
or later) to back up all of the Mac OS X Leopard computers on the network.
What It Looks Like
2.4 or 5 GHz
2.4 or 5 GHz
AirPort Extreme
2.4 or 5 GHz
Ethernet WAN port
<
Time Capsule
DSL or cable modem
to Internet
USB Printer
What to Do
Follow the instructions in the previous sections to set up your AirPort Extreme
network depending on how you connect to the Internet or set up your wireless
network. Connect a USB hard disk, printer, or hub to the USB port on your
AirPort Extreme Base Station or Time Capsule.
Note: If you’re using an AirPort Express in your network, you can connect a USB printer
to the USB port, and everyone on the network can print to it. AirPort Express doesn’t
support connecting a USB hard disk.
40
Chapter 3 AirPort Network Designs
Using Apple TV on Your AirPort Extreme Network to Play Content from iTunes
When you connect Apple TV to your AirPort Extreme network wirelessly, or using
Ethernet, and then connect Apple TV to your widescreen TV, you can enjoy your
favorite iTunes content including movies, TV shows, music, and more. (See the
documentation that came with your Apple TV for instructions setting it up.)
to Ethernet port
2.4 or 5 GHz
Time Capsule
Ethernet WAN port
<
2.4 GHz
Apple TV
DSL or cable modem
to Internet
Setting Advanced Options
Connecting Additional Wireless Devices to Your AirPort Network
You can connect additional Apple wireless devices to extend the range of your
wireless network. For example, you can connect an AirPort Extreme Base Station or
a Time Capsule using Ethernet. A network with devices connected using Ethernet is
known as a roaming network. You can also connect Apple wireless devices wirelessly to
extend the network.
Chapter 3 AirPort Network Designs
41
Setting Up Roaming
Several AirPort Extreme Base Stations or Time Capsules can be set up to create a single
wireless network. Client computers using AirPort can move from device to device with
no interruption in service (a process known as roaming).
To set up roaming:
1 Connect all of the AirPort Extreme Base Stations and Time Capsules to the same subnet
on your Ethernet network.
2 Give each device a unique name.
3 Give each device the same network name and password.
4 Set up the devices as bridges, following the instructions in the previous section.
If you want one device to assign IP addresses using DHCP, also do the following:
1 Set up one device to act as the DHCP server.
2 Set up the other devices as bridges, following the instructions in the previous section.
The device acting as a DHCP server can also receive its IP address via DHCP from a
server on an Ethernet network or from a cable or DSL modem connected to an Internet
service provider (ISP).
2.4 GHz
Time Capsule AirPort Extreme
2.4 or 5 GHz
Ethernet WAN port
<
DSL or cable modem
to Internet
Ethernet LAN ports
to Ethernet port
G
42
Chapter 3 AirPort Network Designs
Extending the Range of an 802.11n Network
Extending the range of an 802.11n network is simpler if you’re connecting another
802.11n device. Connecting two Apple 802.11n wireless devices makes the WDS setup
process more straightforward.
To extend the range of an 802.11n network:
1 Open AirPort Utility and select the device that will connect to the Internet. See the
previous sections of this document for instructions about setting up your wireless
device, depending on your Internet connection.
2 Choose Base Station > Manual Setup, or double-click the device’s icon to open the
configuration in a separate window. Enter the password if necessary.
3 Click the AirPort button, and then click Wireless.
4 Choose“Create a wireless network”from the Wireless Mode pop-up menu, and then
select the“Allow this network to be extended”checkbox.
5 Next, select the device that will extend this network and choose Base Station > Manual
Setup, or double-click the device’s icon to open its configuration in a separate window.
Enter the password if necessary.
6 Choose“Extend a wireless network”from the Wireless Mode pop-up menu, and then
choose the network you want to extend from the Network Name pop-up menu.
7 Enter the network name and password if necessary.
Chapter 3 AirPort Network Designs
43
8 Click Update to update the device with new network settings.
Controlling the Range of Your AirPort Network
You can also shorten the range of your AirPort network. This might be useful if you
want to control who has access to the network by restricting the range to a single
room, for example.
To shorten the range of your AirPort network:
1 Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh
computer, or in Start > All Programs > AirPort on a computer using Windows).
2 Select your wireless device and choose Base Station > Manual Setup, or double-click
the device icon to open its configuration in a separate window. Enter the password
if necessary.
3 Click the AirPort button, and then click Wireless.
4 Click Wireless Options, and then choose a percentage setting from the Transmit Power
pop-up menu. The lower the percentage is, the shorter the range is.
44
Chapter 3 AirPort Network Designs
Keeping Your Network Secure
Your network is protected by the password you assign to it. However, you can take
additional steps to help keep your network secure.
Networks managed by Simple Network Management Protocol (SNMP) may be
vulnerable to denial-of-service attacks. Similarly, if you configure your wireless device
over the WAN port, it may be possible for unauthorized users to change network
settings. When remote configuration is enabled, the device’s Bonjour information
(the device name and IP address) is published over the WAN port. Turning off remote
configuration may provide additional security.
To help protect your network and wireless device:
1 Open AirPort Utility, select your device, and choose Base Station > Manual Setup, or
double-click the device icon to open its configuration in a separate window. Enter the
password if necessary.
2 Click the Advanced button, and then click Logging & SNMP.
3 Make sure the Allow SNMP Access and“Allow SNMP over WAN”checkboxes are not
selected.
Using Wi-Fi Protected Access
AirPort Extreme supports WPA and WPA2 security standard for wireless networks. Using
Mac OS X v10.3 or later or Windows XP with Service Pack 2, and 802.1X authentication
capabilities, WPA security delivers more sophisticated data encryption than WEP, and
also provides user authentication, which was virtually unavailable with WEP. If your
computer has an AirPort Extreme wireless card installed, you can take advantage of the
security updates in WPA2, including AES-CCMP encryption.
AirPort Extreme supports two modes of WPA and WPA2: Enterprise mode, which uses
an authentication server for user authentication, and Personal mode, which relies on
the capabilities of TKIP for WPA and AES-CCMP for WPA2, without requiring an
authentication server.
Enterprise mode is designed for a larger network in which an IT professional is most
likely setting up and managing the network. In order to set up a WPA or WPA2
Enterprise network, an 802.1X connection must be set up first in Network preferences
on a Mac. To set up an 802.1x connection on a Windows computer, see the
documentation that came with your computer. The 802.1X connection requires an
authentication protocol, like TTLS, LEAP, or PEAP.
Setting up a WPA or WPA2 Enterprise network requires setting up an authentication
server, such as a RADIUS server, to manage and validate network users’ credentials,
such as user names, passwords, and user certificates. See the documentation that
came with the server to set it up.
Chapter 3 AirPort Network Designs
45
Personal mode is for the home or small office network and can be set up and
managed by most users. Personal mode does not require a separate authentication
server. Network users usually only need to enter a user name and password to join
the network.
Note: If you change an existing WDS network from WEP to WPA, you’ll need to reset
the wireless devices and set up your network again. For information about resetting
your Apple wireless device, see the documentation that came with it.
To set up a WPA or WPA2 Enterprise network:
On a computer using Mac OS X, you first need to set up an 802.1x connection.
1 Open System Preferences, click Network, and then click AirPort.
2 Click Advanced, and then click 802.1X
3 Enter the settings for the connection.
Note: Some of the authentication protocols require digital certificate authorization on
the server. See the documentation that came with your server to create and distribute
digital certificates.
4 Click OK to save the connection settings.
To use AirPort Utility to set up a WPA or WPA2 Enterprise network on computers
using Mac OS X and Windows XP:
1 Open AirPort Utility, select your wireless device, and then choose Base Station >
Manual Setup, or double-click the device icon to open its configuration in a separate
window. Enter the password if necessary.
2 Choose WPA/WPA2 Enterprise, or WPA2 Enterprise from the Wireless Security
pop-up menu, depending on the capabilities of the client computers that will join
your network.
3 Click Configure RADIUS, and enter the IP address, port, and shared secret (or password)
of the primary and secondary RADIUS authentication servers. Check with the
administrator of the RADIUS server for information to type in these fields.
To set up a WPA or WPA2 Personal network:
1 Open AirPort Utility, select your wireless device, and then choose Base Station >
Manual Setup, or double-click the device icon to open its configuration in a separate
window. Enter the password if necessary.
2 Choose WPA/WPA2 Personal or WPA2 Personal from the Wireless Security pop-up menu
depending on the capabilities of the client computers that will join your network.
3 Type a password of 8 to 63 ASCII characters.
46
Chapter 3 AirPort Network Designs
Setting Up Access Control
Access control lets you specify which computers can send or receive information
through the wireless device to the wired network.
Each wireless-enabled computer has a unique MAC address. You can restrict access by
creating an access control list that includes only the MAC addresses for computers you
want to access your wired network.
To find the MAC address (AirPort ID) of your computer’s AirPort Card, click the AirPort
button in the Network pane of System Preferences.
To set up the access control list:
1 Open AirPort Utility, select your wireless device, and then choose Base Station >
Manual Setup. Enter the password if necessary.
2 Click the AirPort button, and then click Access.
3 Choose Timed Access or RADIUS from the MAC Address Access Control pop-up menu,
depending on the device you’re setting up.
 If you choose Timed Access, click the Add (+) button and enter the MAC address and
description or name of the computers you’re allowing to access the network. You can
also click This Computer to add the MAC address and name of the computer you’re
using to set up this wireless device. Double-click the computer in the list and choose
a value from each pop-up menu. Choose a day of the week or Everyday from the day
pop-up menu, and then choose either“all day”or“between”from the other pop-up
menu. If you choose“between,”you can edit the times of the day by double-clicking
in the time fields.
Chapter 3 AirPort Network Designs
47
 If you choose RADIUS, enter the type of RADIUS service, the RADIUS IP addresses,
shared secret, and primary port for the primary RADIUS server. Enter the information
if you don’t have that information.
Important: AirPort access control prevents computers that aren’t on the access control
list from accessing the AirPort network. For information on how to prevent
unauthorized computers from joining the AirPort network, see “Setting Up the
AirPort Extreme Network”on page 17.
You can also add the MAC address of a third-party 802.11 wireless networking card to
the access control list. Most third-party cards have the MAC address on a label attached
to the metal case of the card.
Access control is not compatible with WPA or WPA2 Enterprise mode. You can use
either access control or WPA Enterprise in a network, but you can’t use both.
Using a RADIUS Server
Using a RADIUS server on your network lets you authenticate MAC addresses
(AirPort IDs) on a separate computer, so that each device on the network doesn’t
need to store the MAC addresses of computers that have access to the network.
Instead, all the addresses are stored on a server that is accessed through a specific
IP address.
To set up authentication using a RADIUS server:
1 On the server, enter the MAC addresses of the computers that will access the network.
2 When the RADIUS server is set up, open AirPort Utility, select your wireless device, and
then choose Base Station > Manual Setup, or double-click the device icon to open its
configuration in a separate window. Enter the password if necessary.
3 Click AirPort, click Access, and then choose RADIUS from the MAC Address Access
Control pop-up menu.
4 Choose a format from the RADIUS pop-up menu.
If you choose Default, your wireless device formats the MAC addresses as 010203-
0a0b0c, and they are used as the user names on the RADIUS server. The shared secret is
the password for users joining the network. This format is often used for Lucent and
Agere servers.
If you choose Alternate, MAC addresses are formatted as 0102030a0b0c and are used
for both the user name and password by users joining the network. This format is often
used for Cisco servers.
48
Chapter 3 AirPort Network Designs
5 Enter the IP address, port, and shared secret (or password) for the primary and
secondary servers.
See the RADIUS documentation that came with your server, or check with the network
administrator for more information on setting up the RADIUS server.
The access control list and RADIUS work together. When a user tries to join a network
that authenticates using access control or a RADIUS server, the wireless device searches
first in the access control list, and if the MAC address is there, the user can join the
network. If the MAC address is not in the access control list, the device checks the
RADIUS server for the MAC address. If it is there, the user can join the network.
Note: RADIUS access control is not compatible with WPA or WPA2 Personal mode.
You can use either RADIUS access control or WPA Enterprise in a network, but you can’t
use both.
Directing Network Traffic to a Specific Computer on Your
Network (Port Mapping)
AirPort Extreme uses Network Address Translation (NAT) to share a single IP address
with the computers that join the AirPort Extreme network. To provide Internet access
to several computers with one IP address, NAT assigns private IP addresses to each
computer on the AirPort Extreme network, and then matches these addresses with
port numbers. The wireless device creates a port-to-private IP address table entry
when a computer on your AirPort (private) network sends a request for information to
the Internet.
Chapter 3 AirPort Network Designs
49
If you’re using a web, AppleShare, or FTP server on your AirPort Extreme network, other
computers initiate communication with your server. Because the Apple wireless device
has no table entries for these requests, it has no way of directing the information to the
appropriate computer on your AirPort network.
To ensure that requests are properly routed to your web, AppleShare, or FTP server, you
need to establish a permanent IP address for your server and provide inbound port
mapping information to your Apple wireless device.
To set up inbound port mapping:
1 Open AirPort Utility, select your wireless device, and then choose Base Station >
Manual Setup, or double-click the device icon to open its configuration in a separate
window. Enter the password if necessary.
2 Click the Advanced button, and then click Port Mapping.
3 Click the Add (+) button and choose a service, such as Personal File Sharing, from the
Service pop-up menu.
50
Chapter 3 AirPort Network Designs
Type any additional information you need in the text fields.
To use port mapping, you must configure TCP/IP manually on the computer that is
running the web, AppleShare, or FTP server.
You can also set up a computer as a default host to establish a permanent IP
address for the computer and provide inbound port mapping information to the
AirPort Extreme Base Station or AirPort Express. This is sometimes known as a DMZ
and is useful when playing some network games or video conferencing.
To set up a default host:
1 Open AirPort Utility, select your wireless device, and then choose Base Station >
Manual Setup, or double-click the device icon to open its configuration in a separate
window. Enter the password if necessary.
2 Click the Internet button, and then click NAT.
3 Select the“Enable Default Host at”checkbox. The default IP address is 10.0.1.253.
4 Enter the same IP address on the host computer.
Logging
You can set up your wireless device to log status information to the Mac OS X system
log or the Syslog application on a Windows computer. This is helpful for understanding
problems and monitoring a device’s performance.
To set up logging:
1 Open AirPort Utility, select your wireless device, and then choose Base Station >
Manual Setup, or double-click the device icon to open its configuration in a separate
window. Enter the password if necessary.
2 Click the Advanced button, and then click Statistics.
Chapter 3 AirPort Network Designs
51
3 Enter the IP address of the computer that will receive the logs in the Syslog Destination
Address field.
4 Choose a level from the Syslog Level pop-up menu.
You need to assign a Network Time Protocol (NTP) server for each wireless device,
so the log information will contain the accurate time of the status logs.
To set the time automatically:
1 Open AirPort Utility, select your wireless device, and then choose Base Station >
Manual Setup, or double-click the device icon to open its configuration in a separate
window. Enter the password if necessary.
2 Click the AirPort button, and then click Base Station.
3 Select the“Set time automatically”checkbox, and then choose an NTP server from the
pop-up menu if you have access to one on your network or on the Internet.
If you click“Logs and Statistics”you can view and export logs, and view wireless client
and DHCP client information.
If you export the logs, use the Mac OS X Console application, located in the Utilities
folder in the Applications folder on a Mac, or in Start > All Programs > AirPort on a
Windows computer, to view the logs on the computer receiving them.
Using Back to My Mac on your Wireless Network
If you have a paid MobileMe subscription (not a free trial), you can use Back to My Mac
to access your AirPort Base Station or Time Capsule. You can access the base station or
Time Capsule to monitor the network or make changes to the base station or Time
Capsule settings.
You can also access the hard disk built into the Time Capsule or an external USB hard
disk connected to the base station or Time Capsule.
To set up Back to My Mac on your wireless device:
1 Click MobileMe in the Advanced pane.
2 Enter your MobileMe account and password.
52
Chapter 3 AirPort Network Designs
Setting up IPv6
IPv6 is a new version of Internet Protocol (IP). IPv6 is currently used primarily by some
research institutions. Most computers do not need to set up or use IPv6.
The primary advantage of IPv6 is that it increases the address size from 32 bits (the
current IPv4 standard) to 128 bits. An address size of 128 bits is large enough to support
billions and billions of addresses. This allows for more addresses or nodes than are
currently available. IPv6 also provides more ways to set up the address and simpler
autoconfiguration.
By default, IPv6 is configured automatically, and the default settings are sufficient.
However, if your network administrator or Internet service provider (ISP) has specifically
told you to configure IPv6 manually, follow the instructions below.
Open AirPort Utility, select your wireless device, and then choose Base Station >
Manual Setup. Enter the password if necessary. Click the Advanced button, and then
click IPv6.
To manually set IPv6 options:
1 Choose Node or Tunnel from the IPv6 mode pop-up menu, depending on the method
you were instructed to use.
2 Choose Manually from the Configure IPv6 pop-up menu, and enter the information you
were given from your ISP or network administrator.
Customizing the IPv6 firewall
If your wireless device supports it, you can use AirPort Utility to adjust IPv6 firewall
settings.
To adjust IPv6 firewall settings:
1 Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac,
or in Start > All Programs > AirPort on a Windows computer.
2 Select your device from the list, and then enter the password.
3 Click the Advanced button, and then click IPv6 Firewall
By default,“Allow Teredo tunnels”and“Allow incoming IPSec authentication”are
selected.
To provide access to specific devices on your network from outside the IPv6 firewall,
click the Add (+) button and enter the IPv6 address and/or the port for the device.
To use an IPv6 firewall, you need an Apple 802.11n wireless device.
Chapter 3 AirPort Network Designs
53
Sharing and Securing USB Hard Disks on Your Network
If you connect a USB hard disk to your AirPort Extreme Base Station or Time Capsule,
computers connected to the network—both wireless and wired, Mac and Windows—
can use it to back up, store, and share files.
If you’re using a Time Capsule, you don’t need to connect a hard disk to it. Every Time
Capsule includes an internal AirPort disk.
AirPort Extreme USB hard disk
2.4 or 5 GHz
2.4 or 5 GHz
DSL or cable modem
to Internet
Ethernet WAN port
<
To share a hard disk on your network:
1 Plug the hard disk into the USB port on the back of the AirPort Extreme Base Station
or Time Capsule.
2 Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac,
or in Start > All Programs > AirPort on a Windows computer.
3 Select your AirPort Extreme Base Station or your Time Capsule, and then choose Base
Station > Manual Setup, or double-click the device icon to open its configuration in a
separate window. Enter the password if necessary.
4 Click the Disks button, and then click File Sharing.
5 Choose“With a disk password,”or“With base station password”if you want to secure
the shared disk with a password, or choose“With accounts”if you want to secure the
disk using accounts.
 If you choose to use accounts, click Configure Accounts, click the Add (+) button,
and then enter a name and password for each user that will access the disk.
6 Choose “Not allowed,”“Read only,” or “Read and write” to assign guest access to
the disk.
7 Select the“Share disks over Ethernet WAN port”checkbox if you want to provide
remote access to the disk over the WAN port.
Data transfer speed may vary, depending on the network.
54
Chapter 3 AirPort Network Designs
Using a Time Capsule in Your Network
If you’re using a Time Capsule and a computer with Mac OS X Leopard (v10.5.2 or later),
you can use Time Machine to automatically back up all of the computers on the
network that are using Leopard. Other Mac computers and Windows computers can
access the Time Capsule’s internal AirPort disk to back up, store, and share files.
And because every Time Capsule is also a full-featured 802.11n base station, you can set
up your Time Capsule to share an Internet connection with computers on the AirPort
network it creates.
Time Capsule
2.4 GHz
2.4 or 5 GHz
2.4 or 5 GHz
DSL or cable modem
to Internet
Ethernet WAN port
<
For information about using your Time Capsule with Time Machine in Mac OS X
Leopard, search for“Time Capsule”in Mac Help.
Connecting a USB Printer to an Apple Wireless Device
You can connect a compatible USB printer to your Apple wireless device (an AirPort
Extreme Base Station, AirPort Express, or Time Capsule), so that anyone on the network
using Mac OS X v10.2.3 or later, Windows XP with Service Pack 2, or Windows Vista can
print to that printer.
To use a printer on your network:
1 Connect the printer to the USB port on the Apple wireless device.
2 Set up the client computers:
 On a computer using Mac OS X v10.5 or later, open System Preferences and click
Print & Fax. Select the printer from the Printers list. If the printer isn’t in the list, click
Add (+) at the bottom of the list, locate the printer, and then click Add.
 On a computer using Mac OS X v10.2.3 or later, open Printer Setup Utility located in
the Utilities folder in the Applications folder, and then select the printer from the list.
If the printer is not in the list, click Add, choose Bonjour from the pop-up menu, and
then select the printer from the list.
Chapter 3 AirPort Network Designs
55
 On a computer using Windows, install Bonjour for Windows from AirPort Utility CD,
and follow the onscreen instructions to connect to the printer.
You can change the name of the printer from the default name to one you choose.
To change the name of your USB printer:
1 Open AirPort Utility, select your device, and then choose Base Station > Manual Setup,
or double-click the device icon to open its configuration in a separate window.
2 Click the Printer button and type a name for the printer in the USB Printers field.
Adding a Wireless Client to Your 802.11n Network
If your Apple wireless device supports it, and your network is password-protected using
WPA Personal or WPA/WPA2 Personal, you can provide wireless clients access to your
network without requiring them to enter the network password.
When you allow a client access to your network, the client’s name and wireless MAC
address (or AirPort ID) are stored in the access control list of AirPort Utility until you
remove them from the list. You can provide 24 hours of access, after which time the
client will no longer be able to access your network.
When you provide a client access to your wireless network, the client does not need to
enter the network password.
To allow client access to your network:
1 Open AirPort Utility, located in the Utilities folder in the Applications folder on a Mac,
or in Start > All Programs > AirPort on a Windows computer.
2 Select your Apple wireless device and choose Base Station > Manual Setup. Enter the
password if necessary.
3 Choose Add Wireless Clients from the Base Station menu.
4 Select how you want the client to access the network:
 Select PIN to enter the eight-digit number provided by the client requesting network
access.
 Select “First attempt” to allow network access to the first client attempting to join
the network.
 Select“Limit client’s access to 24 hours”if you want to provide only one day of access
to your network. If you don’t select this option, the client will have access to your
network until you remove the name from the list.
56
Chapter 3 AirPort Network Designs
Solving Problems
If you have trouble connecting to the Internet with any AirPort Extreme network
design, try the following:
On a computer using Mac OS X:
 Make sure the wireless device is connected to the Internet. The computers on your
AirPort network cannot connect to the Internet if your device is not connected to
the Internet.
 Check your Internet connection using your computer. If you can’t connect with your
computer, the problem may be with your Internet connection.
 On a Mac using Mac OS X v10.5, check the active network services in the Network
pane of System Preferences. Make sure the ports you want to use are active.
 Open Network preferences and then click AirPort. Make sure that the computer has
joined the AirPort network created by your wireless device.
 Restart your computer. This renews the IP address you receive from the wireless
device. The IP addresses should be in the range of 10.0.1.2 to 10.0.1.200, 172.16.1.2 to
172.16.1.200, or 192.168.1.2 to 192.168.1.200, depending on the address scheme the
wireless device uses.
 If the wireless device is set up as a DHCP server, make sure you choose“Share a
public IP address”from the Connection Sharing pop-up menu on the Internet
Connection pane of Internet settings in AirPort Utility.
 If you’re using a cable modem and your wireless device cannot connect to the
Internet, turn off the cable modem, wait a few minutes, and then turn it on again.
On a computer using Windows:
 Make sure the wireless device is connected to the Internet. The computers on your
AirPort network cannot connect to the Internet if your device is not connected to the
Internet.
 Check your Internet connection using your computer. If you can’t connect with your
computer, the problem may be with your Internet connection.
 Right-click the wireless connection icon, and then choose Status.
Chapter 3 AirPort Network Designs
57
 Make sure that the computer has joined the AirPort network created by your wireless
device.
 Restart your computer. This renews the IP address you receive from the wireless
device. The IP addresses should be in the range of 10.0.1.2 to 10.0.1.200, 172.16.1.2 to
172.16.1.200, or 192.168.1.2 to 192.168.1.200 depending on the address scheme the
device uses.
 If the device is set up as a DHCP server, make sure the“Obtain an IP address
automatically”checkbox is selected in the General pane of Internet Protocol (TCP/IP)
Properties. Right-click the wireless connection icon and click Properties. Click Internet
Protocol (TCP/IP), and then click Properties.
More Information About AirPort
You can find more information about AirPort in the following locations:
 AirPort Utility Help
Look in AirPort Utility Help for information on setting up an AirPort Extreme network;
using an AirPort Extreme Base Station, an AirPort Express, or a Time Capsule; editing
settings; avoiding sources of interference; locating additional information on the
Internet; and more. On a computer using Mac OS X, open AirPort Utility and choose
Help > AirPort Utility Help. On a computer using Windows, open AirPort Utility and
click Help.
 World Wide Web
58
Chapter 3 AirPort Network Designs
4
Behind the Scenes
4
This chapter defines terms and concepts used to discuss
computer networks. Use it as a reference to help you
understand what is taking place behind the scenes of your
AirPort wireless network.
Basic Networking
Packets and Traffic
Information travels across a network in chunks called packets. Each packet has a
header that tells where the packet is from and where it’s going, like the address on
the envelope when you send a letter. The flow of all these packets on the network
is called traffic.
How Information Reaches Its Destination
Hardware Addresses
Your computer “listens” to all of the traffic on its local network and selects the
packets that belong to it by checking for its hardware address (also called the media
access control, or MAC address) in the packet header. This address is a number unique
to your computer.
Every hardware product used for networking is required to have a unique hardware
address permanently embedded in it. Your AirPort Card’s number is called the
AirPort ID.
IP Addresses
Since the Internet is a network of networks (connecting millions of computers),
hardware addresses alone are not enough to deliver information on the Internet. It
would be impossible for your computer to find its packets in all the world’s network
traffic, and impossible for the Internet to move all traffic to every network.
59
So, your computer also has an Internet Protocol (IP) address that defines exactly where
and in what network it’s located. IP addresses ensure that your local Ethernet network
receives only the traffic intended for it. Like the hierarchical system used to define zip
codes, street names, and street numbers, IP addresses are created according to a set of
rules, and their assignment is carefully administered.
The hardware address is like your name; it uniquely and permanently identifies you. But
it doesn’t offer any clues about your location, so it’s only helpful in a local setting. An IP
address is like your street address, which contains the information that helps letters
and packages find your house.
Rules for Sending Information (Protocols)
A protocol is a set of rules that define how communication takes place. For instance, a
networking protocol may define how information is formatted and addressed, just as
there’s a standard way to address an envelope when you send a letter.
Using the AirPort Extreme Base Station
This section describes the different network interfaces of the AirPort Extreme Base
Station and describes the functions the base station can provide.
Base Station Interfaces
To use the AirPort Extreme Base Station, you configure how its networking interfaces
will be used. The AirPort Extreme Base Station has five hardware networking interfaces:
 AirPort interface: The AirPort interface creates an AirPort network for AirPort-
enabled computers to join. The base station can provide IP services such as DHCP
and NAT using this interface. The base station cannot use the AirPort interface to
establish a connection with the Internet.
 Ethernet WAN (<) interface: Use the Ethernet WAN interface to connect DSL
or cable modems and connect to the Internet.
 Ethernet LAN (G) interface: If your base station has one or more Ethernet LAN
interface ports, you can use them to provide IP services to local Ethernet clients.
 USB (d) interface: Use the USB interface to connect a USB printer or hard disk to the
AirPort Extreme Base Station.
∏
Status light
Ethernet WAN port
Ethernet ports
Reset button
<
G
¯
Power port
d USB port
Security slot
60
Chapter 4 Behind the Scenes
Using the Time Capsule
This section describes the different network interfaces of the Time Capsule and
describes the functions it can provide.
Time Capsule Interfaces
To use your Time Capsule, you configure how its networking interfaces will be used.
The Time Capsule has five hardware networking interfaces:
 AirPort interface: The AirPort interface creates an AirPort network for AirPort-
enabled computers to join. The Time Capsule can provide IP services such as DHCP
and NAT using this interface. The Time Capsule cannot use the AirPort interface to
establish a connection with the Internet.
 Ethernet WAN (<) interface: Use the Ethernet WAN interface to connect DSL
or cable modems and connect to the Internet.
 Ethernet LAN (G) interface: The Time Capsule has three Ethernet LAN interface
ports. You can use them to provide IP services to local Ethernet clients.
 USB (d) interface: Use the USB interface to connect a USB printer to the Time
Capsule.
Status light
< Ethernet WAN port
Ethernet ports
G
≤
Power port
d USB port
∏
Reset button Security slot
Using the AirPort Express
This section describes the different network interfaces of the AirPort Express Base
Station and describes the functions the base station can provide.
AirPort Express Interfaces
To set up the AirPort Express Base Station, you configure how its networking interfaces
will be used. The AirPort Express Base Station has four hardware networking interfaces:
 AirPort interface: The AirPort interface creates an AirPort network for AirPort-
enabled computers to join. The base station can provide IP services such as DHCP
and NAT using this interface. The base station cannot use the AirPort interface to
establish a connection with the Internet.
 Ethernet WAN (<) interface: Use the Ethernet WAN interface to connect DSL
or cable modems and connect to the Internet.
 USB (d) interface: Use the USB interface to connect a USB printer to the
AirPort Extreme Base Station.
Chapter 4 Behind the Scenes
61
 Audio (-) interface: Use the analog and optical digital audio stereo mini-jack to
connect an AirPort Express to a home stereo or powered speakers.
Status light
AC plug adapter
d USB port
∏ Reset button
-
Ethernet port
Line Out port
G
(Analog and optical
digital audio mini-jack)
Apple Wireless Device Functions
 Bridge: Each Apple wireless device is configured by default as a bridge between the
wireless AirPort network and the wired Ethernet network. Connecting an AirPort
network to an Ethernet network through the device’s Ethernet LAN port (G) bridges
the wireless AirPort network to the wired Ethernet network.
Important: If you’re connecting an Ethernet network to the device’s Ethernet LAN
port (G), make sure the Ethernet network does not have an Internet connection.
 NAT router: One of the most powerful features of Apple wireless devices is their
ability to share one Internet connection with several computers. To provide this
service, the device acts as a router. The device can be configured to provide both
bridging services and routing services at the same time.
 DHCP server: When you configure the wireless device to act as a DHCP server,
it provides IP addresses to both wired and wireless client computers that are
configured to obtain IP addresses using DHCP. Using DHCP makes IP configuration
simple for client computers, since they don’t need to enter their own IP information.
62
Chapter 4 Behind the Scenes
Items That Can Cause Interference with AirPort
The farther away the interference source, the less likely it is to cause a problem.
The following items can cause interference with AirPort communication:
 Microwave ovens
 DSS (Direct Satellite Service) radio frequency leakage
 The original coaxial cable that came with certain types of satellite dishes. Contact
the device manufacturer and obtain newer cables.
 Certain electrical devices, such as power lines, electrical railroad tracks, and power
stations
 Cordless telephones that operate in the 2.4 gigahertz (GHz) range. If you have
problems with your phone or AirPort communication, change the channel of
your base station.
 Other AirPort and wireless networks
 Adjacent base stations using nearby channels. If base station A is set to channel 1,
base station B should be set to channel 6 or 11. For best results, use channels 1, 6,
or 11 when operating your base station in the 2.4 GHz range.
 Moving objects that temporarily place metal between your computer and the
base station
Chapter 4 Behind the Scenes
63
Glossary
10Base-T The most common cabling method for Ethernet. 10Base-T conforms to IEEE
standard 802.3. It was developed to enable data communications over unshielded
twisted pair (telephone) wiring at speeds of up to 10 megabits per second (Mbps) up to
distances of approximately 330 feet on a network segment.
10/100Base-T A networking standard that supports data transfer rates up to 100 Mbps.
Because it is 10 times faster than Ethernet, it is often referred to as Fast Ethernet.
10/100/1000Base-T A term describing various technologies for transmitting Ethernet
packets at a rate of a gigabit per second. Sometimes referred to as Gigabit Ethernet. In
2000, Apple’s Power Mac G4 and PowerBook G4 were the first mass-produced personal
computers featuring the 10/100/1000Base-T connection. It quickly became a built-in
feature in many other computers.
802.11a An IEEE standard for a wireless network that operates at 5 GHz with rates
up to 54 Mbps.
802.11b An IEEE standard for a wireless network that operates at 2.4 GHz with rates
up to 11 Mbps.
802.11g An IEEE standard for a wireless network that operates at 2.4 GHz Wi-Fi with
rates up to 54 Mbps.
802.11n A task group of the IEEE 802.11 committee whose goal is to define a standard
for high throughput speeds of at least 100 Mbps on wireless networks. Some proposals
being fielded by the task group include designs for up to 540 Mbps, Multiple-input
multiple-output (MIMO) technology, using multiple receivers and multiple transmitters
in both the client and access point to achieve improved performance, is expected to
form the basis of the final specification. See Mbps, MIMO.
access point Also known as a wireless access point (WAP), a device that connects
wireless devices together to form a network.
authentication The process that occurs after association to verify the identity of the
wireless device or end user and allow access to the network. See WPA, WPA2.
64
backbone The central part of a large network that links two or more subnetworks.
The backbone is the primary data transmission path on large networks such as those of
enterprises and service providers. A backbone can be wireless or wired.
bandwidth The maximum transmission capacity of a communications channel at
any point in time. Bandwidth, usually measured in bits per second (bps), determines
the speed at which information can be sent across a network. If you compare the
communications channel to a pipe, bandwidth represents the pipe width and
determines how much data can flow through the pipe at any one time. The greater
the bandwidth, the faster data can flow. See bps.
base station In the area of wireless computer networking, a base station is a radio
receiver/transmitter that serves as the hub of the local wireless network, and may also
be the gateway between a wired network and the wireless network. A base station can
also be referred to as an access point or router.
Bluetooth A technology designed for short-range, wireless communications among
computing devices and mobile products, including PCs and laptop computers,
personal digital assistants, printers, and mobile phones. Designed as a cable
replacement, Bluetooth enables short-range transmission of voice and data in the 2.4
GHz frequency spectrum within a range of about 30 feet.
bps Bits per second. A measure of data transmission speed across a network or
communications channel; bps is the number of bits that can be sent or received per
second. It measures the speed at which data is communicated and should not
be—but often is—confused with bytes per second. Whereas“bits”is a measure of
transmission speed,“bytes”is a measure of storage capacity. See bandwidth, Mbps.
bridge A wireless device that connects multiple networks together. Using an access
point as a bridge turns off Network Address Translation (NAT) and DHCP routing and
simply extends the range of service.
broadband A comparatively fast Internet connection possessing sufficient bandwidth
to accommodate multiple voice, data, and video channels simultaneously. Cable, DSL,
and satellite are all considered to be broadband channels; they provide much greater
speed than dial-up Internet access over telephone wires. See cable modem, DSL.
broadband modem A device that connects a local computer or network to a high-
speed Internet service, such as DSL or Cable Internet. See cable modem, DSL.
cable modem A device used with broadband Internet service provided by a
traditional cable TV service. Cable modems convert analog data from the cable TV
system into a digital format that can be used by a computer. See broadband modem.
Glossary
65
channel One portion of the available radio spectrum that all devices on a wireless
network use to communicate. Changing the channel on the access point/router can
help reduce interference.
client Any computer or device connected to a network that requests files and services
(files, print capability) from the server or other devices on the network. The term also
refers to end users.
DHCP Dynamic Host Configuration Protocol. A protocol for dynamically assigning IP
addresses from a predefined list to nodes on a network. When they log on, network
nodes automatically receive an IP address from a pool of addresses served by a DHCP.
The DHCP server provides (or leases) an IP address to a client for a specific period of
time. The client will automatically request a renewal of the lease when the lease is
about to run out. If a lease renewal is not requested and it expires, the address is
returned to the pool of available IP addresses. Using DHCP to manage IP addresses
simplifies client configuration and efficiently utilizes IP addresses. See IP address.
DNS Domain Name System. An Internet service that translates alphanumeric domain
names to assigned IP addresses and vice versa. The term is typically used to describe
the server that makes the translation. Every website has its own specific IP address on
the Internet. DNS typically refers to a database of Internet names and addresses that
translates the alphanumeric names to the official Internet Protocol numbers and vice
versa. For instance, a DNS server converts a name like mywebsite.com to a series of
numbers like 107.22.55.26. See IP, IP address.
DSL Digital Subscriber Line. A dedicated digital circuit between a residence or
business and a telephone company’s central office. It allows high-speed data, voice,
and video transmissions over existing twisted-pair copper plain old telephone service
(POTS) telephone wires. See broadband.
dual-band A device that is capable of operating in either of two frequencies. On a
wireless network, dual-band devices are capable of operating in the 2.4 GHz (802.11b/g)
or 5 GHz (802.11a) bands.
encryption A mechanism for providing data confidentiality. See WPA, WPA2.
Ethernet The most popular international standard technology for wired local area
networks (LANs). It provides from 10 Mbps transmission speeds on basic 10Base-T
Ethernet networks to 100 Mbps transmission speeds on Fast Ethernet networks, 1000
Mbps on Gigabit Ethernet, and 10,000 Mbps on 10 Gigabit Ethernet.
66
Glossary
firewall A system of software and/or hardware that resides between two networks to
prevent access by unauthorized users. The most common use of a firewall is to provide
security between a local network and the Internet. Firewalls can make a network
appear invisible to the Internet and can block unauthorized and unwanted users from
accessing files and systems on the network. Hardware and software firewalls monitor
and control the flow of data in and out of computers in both wired and wireless
enterprise, business and home networks. They can be set to intercept, analyze, and
stop a wide range of Internet intruders and hackers.
gateway In the wireless world, a gateway is an access point with additional software
capabilities such as providing NAT and DHCP. Gateways may also provide VPN support,
roaming, firewalls, various levels of security, and so on.
hotspot A location where users can access the Internet using Wi-Fi laptops and other
Wi-Fi enabled devices. Access may be provided free or for a fee. Hotspots are often
found at coffee shops, hotels, airport lounges, train stations, convention centers, gas
stations, truck stops, and other public meeting areas. Corporations and campuses often
offer hotspot service to visitors and guests. Hotspot service is sometimes available
aboard planes, trains, and boats.
hub A multiport device used to connect client devices to a wired Ethernet network.
Hubs can have numerous ports and can transmit data at speeds ranging from 10 to
1000 Mbps to all the connected ports. A small wired hub may only connect 4
computers; a large hub can connect 48 or more. See router.
IEEE 802.11 The family of specifications developed by the Institute of Electrical and
Electronics Engineers (IEEE) 802.11 committee, which establishes standards for wireless
Ethernet networks. 802.11 standards define the over-the-air interface between wireless
clients and a base station, or an access point that is physically connected to the wired
network.
IP Internet Protocol. The basic communications protocol of the Internet. See IP
address, TCP/IP.
IP address Internet Protocol address. IP Version 4, the most widely used Internet
protocol, provides a 32-bit number that identifies the sender or receiver of information
sent across the Internet. An IP address has two parts: The identifier of the particular
network on the Internet and the identifier of the particular device (which can be
a server or a workstation) within that network. The newer IP, Version 6, provides a
128-bit addressing scheme to support a much greater number of IP addresses.
See DHCP, DNS, IP.
IP subnet An IP subnet is a local network as defined by IP network numbers.
Connecting to a subnet involves connecting to the appropriate hardware network and
configuring IP for that network.
Glossary
67
LAN Local area network. A system of connecting PCs and other devices within the
same physical proximity for sharing resources such as an Internet connections, printers,
files, and drives. When Wi-Fi is used to connect the devices, the system is known as a
wireless LAN or WLAN. See WAN.
MAC address Media Access Control address. A unique hardware number that
identifies each device on a network. A device can be a computer, printer, and so on.
A MAC address is also known as an AirPort ID.
Mbps Megabits per second. A measurement of data speed equivalent to a million bits
per second.
MIMO Multiple-input multiple-output. An advanced signal processing technology that
uses multiple receivers and multiple transmitters in both the client and access point to
achieve data throughput speeds of 100 Mbps. See 802.11n.
NAT Network Address Translation. A network capability that enables multiple
computers to dynamically share a single incoming IP address from a dial-up, cable, or
DSL connection. NAT takes a single incoming public IP address and translates it to a
new private IP address for each client on the network. See DHCP, IP address.
network name A name used to identify a wireless network. See SSID.
NIC Network interface card. A wireless or wired PC adapter card that allows the client
computer to utilize network resources. Most office-wired NICs operate at 100 Mbps.
Wireless NICs operate at data rates defined by 802.11 standards.
packet A unit of information transmitted from one device to another on a network.
A packet typically contains a header with addressing information, data, and a
checksum mechanism to ensure data integrity.
pass phrase A series of characters used to create a key that is used by Wi-Fi Protected
Access (WPA). See PSK, WPA.
print server A network device, often a computer, that connects to at least one printer,
allowing it to be shared among computers on a network.
PSK Pre-shared key. A mechanism in Wi-Fi Protected Access (WPA)-Personal that
allows the use of manually entered keys or passwords to initiate WPA security. The PSK
is entered on the access point or home wireless gateway and each PC that is on the
Wi-Fi network. After entering the password, Wi-Fi Protected Access automatically takes
over. It keeps out eavesdroppers and other unauthorized users by requiring all devices
to have the matching password. The password also initiates the encryption process
which, in WPA is Temporal Key Integrity Protocol (TKIP) and in WPA2 is Advanced
Encryption Standard (AES). See TKIP, WPA-Personal, WPA2-Personal.
68
Glossary
roaming (Wi-Fi) The ability to move from one area of Wi-Fi coverage to another with
no loss in connectivity (hand-off).
router A wireless router is a device that accepts connections from wireless devices
to a network, includes a network firewall for security, and provides local network
addresses. See hub.
server A computer that provides resources or services to other computers and devices
on a network. Types of servers include print servers, Internet servers, mail servers, and
DHCP servers. A server can also be combined with a hub or router. See DHCP, hub,
router.
SSID Service set identifier. A unique 32-character network name, or identifier, that
differentiates one wireless LAN from another. All access points and clients attempting
to connect to a specific WLAN must use the same SSID. The SSID can be any
alphanumeric entry up to a maximum of 32 characters. See network name.
subnet An IP address range that is part of a larger address range. Subnets are used to
subdivide a network address of a larger network into smaller networks. Subnets
connect to other networks through a router. Each individual wireless LAN will typically
use the same subnet for all of its clients. See IP address, router.
TCP Transmission Control Protocol. The transport-level protocol used with the Internet
Protocol (IP) to route data across the Internet. See IP, TCP/IP.
TCP/IP The underlying technology of Internet communications. While IP handles the
actual delivery of data, TCP tracks the data packets to efficiently route a message
through the Internet. Every computer in a TCP/IP network has its own IP address that is
either dynamically assigned at startup (see DHCP) or permanently assigned as a static
address. All TCP/IP messages contain the address of the destination network, as well as
the address of the destination station. This enables TCP/IP messages to be transmitted
to multiple networks (subnets) within an organization or worldwide. For example,
when a user downloads a webpage, TCP divides the page file on the web server into
packets, numbers the packets, and forwards them individually to the user’s IP address.
The packets may be routed along different paths before reaching the user’s address.
At the destination, TCP reassembles the individual packets, waiting until they have all
arrived to present them as a single file. See IP, IP address, packet, TCP.
throughput Usually measured in bps, Kbps, Mbps or Gbps, throughput is the amount
of data that can be sent from one location to another in a specific amount of time.
See bps, Mbps.
USB Universal Serial Bus. A high-speed bidirectional serial connection used to transfer
data between a computer and peripherals such as digital cameras and memory cards.
Glossary
69
WEP Wired equivalent privacy. The original security standard used in wireless
networks to encrypt the wireless network traffic. See WPA, Wireless local area network.
Wi-Fi A term developed by the Wi-Fi Alliance to describe wireless local area network
(WLAN) products that are based on the Institute of Electrical and Electronics Engineers.
Wi-Fi Certified The certification standard designating IEEE 802.11-based wireless local
area network (WLAN) products that have passed interoperability testing requirements
developed and governed by the Wi-Fi Alliance.
wireless network Devices connected to a network using a centralized wireless access
point. See WLAN.
WLAN A data communications network that spans large local, regional, national, or
international areas and is usually provided by a public carrier (such as a telephone
company or service provider).The term is used to distinguish between phone-based
data networks and Wi-Fi networks. Phone networks are considered wide area networks
(WANs) and Wi-Fi networks are considered wireless local area networks (WLANs).
See LAN.
WPA - Enterprise Wi-Fi Protected Access-Enterprise. A wireless security method
that provides strong data protection for multiple users and large managed networks.
It uses the 802.1X authentication framework with TKIP encryption and prevents
unauthorized network access by verifying network users through an authentication
server. See 802.1X.
WPA - Personal Wi-Fi Protected Access-Personal. A wireless security method that
provides strong data protection and prevents unauthorized network access for small
networks. It uses TKIP encryption and protects against unauthorized network access.
WPA2 Wi-Fi Protected Access 2. The follow-on security method to WPA for wireless
networks that provides stronger data protection and network access control. It
provides enterprise and consumer Wi-Fi users with a high level of assurance that only
authorized users can access their wireless networks. Based on the ratified IEEE 802.11i
standard, WPA2 provides government grade security by implementing the National
Institute of Standards and Technology (NIST) FIPS 140-2 compliant AES encryption
algorithm and 802.1X-based authentication. There are two versions of WPA2: WPA2-
Personal and WPA2-Enterprise. WPA2-Personal protects unauthorized network access
by utilizing a set-up password. WPA2-Enterprise verifies network users through a server.
WPA2 is backward compatible with WPA. Like WPA, WPA2 uses the 802.1X/EAP
framework as part of the infrastructure that ensures centralized mutual authentication
and dynamic key management and offers a pre-shared key for use in home and small
office environments. Like WPA, WPA2 is designed to secure all versions of 802.11 devices,
including 802.11b, 802.11a, and 802.11g, multiband and multimode. See WPA2-
Enterprise, WPA2-Personal.
70
Glossary
WPA2 - Enterprise Wi-Fi Protected Access 2 - Enterprise. The follow-on wireless
security method to WPA that provides stronger data protection for multiple users and
large managed networks. It prevents unauthorized network access by verifying
network users through an authentication server. See WPA2.
WPA2 - Personal Wi-Fi Protected Access 2 - Personal. The follow-on wireless security
method to WPA that provides stronger data protection and prevents unauthorized
network access for small networks. See WPA2, PSK.
Glossary
71
© 2009 Apple Inc. All rights reserved.
Apple, the Apple logo, AirPort, AirPort Extreme, AppleShare, AppleTalk, Back to My Mac, Bonjour, Mac,
and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. AirPort Express, AirTunes,
Time Capsule, and Time Machine are trademarks of Apple Inc. Other product and company names mentioned
herein may be trademarks of their respective companies.
019-1257
|