Audiovox Stereo System K 13 User Manual

ASA Electronics TV/VCP Floor Console  
Model K-13 Without Harness and Antenna  
12 Volt DC powered remote controlled 13” television AVT-1475  
12 Volt DC powered remote controlled VHS Video Cassette Player AVP-7000  
Installation Instructions  
Audiovox Specialized Applications, LLC.  
“The Mobile Electronics Company”  
23319 Cooper Drive  
Elkhart IN 46514  
1 (219) 264-3135  
Page1 of 10  
P/N 8007131  
Rev. C 1/12/99 BJ  
 
There are six (6) steps to install the K-13 TV/VCP floor console:  
Step # 1  
Step # 2  
Step # 3  
Step # 4  
Step # 5  
Step # 6  
Disassemble shroud  
Install brackets and straps  
Mount the console on the floor of the vehicle  
Install the VCP  
Install the TV  
Replace the console face and rear shroud  
STEP #1) Disassemble shroud.  
Þ Remove the 4 Phillips screws securing the face of the console.  
Page3 of 10  
P/N 8007131  
Rev. C 1/12/99 BJ  
 
Step #2) Install brackets and straps  
1) Mount brackets, using only four screws. Do not use center hole.  
2) Use soldering iron, if necessary, to melt holes in open strap and loop  
strap, as shown.  
Page4 of 10  
P/N 8007131  
Rev. C 1/12/99 BJ  
 
3) Pre-drill pilot holes on side of VCP shelf (A) and on bottom of TV  
shelf (B) using 1/8” drill bit.  
(A)  
(B)  
Page5 of 10  
P/N 8007131  
Rev. C 1/12/99 BJ  
 
4) Attach both straps, use TV and VCP to help locate strap if  
necessary.  
Page6 of 10  
P/N 8007131  
Rev. C 1/12/99 BJ  
 
Step 3) Install console to floor of vehicle.  
Þ BEFORE DRILLING ANY HOLES VERIFY THAT THE DRILL BIT WILL NOT  
ENTER INTO THE FRAME RAIL(S) OF THE VEHICLE, ELECTRICAL WIRES,  
FUEL LINES, BRAKE LINES, HOSES, EXHAUST SYSTEMS OR ANY OTHER  
ITEMS THAT WILL IMPAIR THE OPERATION OF THE VEHICLE. THE BOLTS  
OF THE FLOOR CONSOLE MUST SECURE TO THE FLOOR PANEL OF THE  
VEHICLE. CLIMB UNDER THE VEHICLE AND LOOK TO VERIFY THAT THE  
HOLES WILL BE IN THE PROPER LOCATIONS.  
Þ Set the console on the floor and of the vehicle and mark where the holes are to  
be drilled. Drill small 1/8” pilot holes to verify that the drill holes are in the  
proper locations.  
Þ After verifying that the 1/8” pilot holes are in the proper locations, use the ¼” drill  
bit to widen out the 1/8” pilot holes.  
Þ Set the console on the floor over the vehicle.  
Þ Place the bolts through the feet of the console and into the holes just drilled.  
Þ Place one large fender washer and one lock washer over each of the bolts and  
attach the nuts.  
Þ Tighten the nuts down securely. Have the second person inside the vehicle hold  
the bolts securely while the person underneath the vehicle tightens down the  
nuts.  
Page7 of 10  
P/N 8007131  
Rev. C 1/12/99 BJ  
 
Step 4) Install the VCP into the console.  
Þ Remove the VCP from the box.  
Þ Connect the white RCA connector (customer supplied) from the console to the  
white audio output of the VCP  
Þ Connect the yellow RCA connector (customer supplied) from the console to the  
yellow audio output of the VCP  
Þ Connect the DC power connector (customer supplied) to the DC power jack of  
the VCP.  
Þ Slide the VCP into the slot in the front of the console  
Þ Secure the VCP into the console with the supplied strap  
Page8 of 10  
P/N 8007131  
Rev. C 1/12/99 BJ  
 
Step 5) Install the TV into the console.  
Þ Connect the yellow RCA patch cord (customer supplied) to the yellow RCA video  
input jack on the rear of the television  
Þ Connect the white RCA patch cord (customer supplied) to the white RCA audio  
input on the rear of the television  
Þ Connect the DC power connector (customer supplied) to the rear of the  
television  
Þ Connect the antenna “F” connector (customer supplied) to the rear of the  
television  
Þ Place the television on the shelf of the console.  
Þ Secure the television down with the strap. Make absolutely certain that the strap  
is tight and  
secure.  
Page9 of 10  
P/N 8007131  
Rev. C 1/12/99 BJ  
 
Step 6) Replace the rear shroud and face of console.  
Þ Place the rear and face of the console over the body of the console. Gently tap  
into place.  
Þ Reinstall the four Phillips screws that held the face to the body.  
Page10 of 10  
P/N 8007131  
Rev. C 1/12/99 BJ  
 

3Com Plumbing Product DUA3700 0BAA04 User Manual
Accusplit Heart Rate Monitor AX740SBL User Manual
ADTRAN Modem 1200153L1 User Manual
ADTRAN Network Card 1100F User Manual
Agilent Technologies Portable Generator E8257D 67D User Manual
Aiphone DJ Equipment BG 10C User Manual
Alto Shaam Food Warmer HFT2 300 User Manual
Asus Clock Radio P4S800D X User Manual
Audiovox Automobile Alarm APS 15R User Manual
Bakers Pride Oven Oven BK 18 User Manual