Avocent Stereo System HGA51G DIR30 User Manual

Quick Installation Guide  
EmergeHGA51G-DIR30  
High Gain 5.1 GHz Directional Antenna  
The following will help you install your directional  
antenna easily. Should you require further assistance,  
please contact Avocent Technical Support.  
Emerge HGA51G-DIR30 Antenna  
Shown with EWMS1000 Extender  
Omni-  
directional  
Antenna  
Directional  
Antenna  
Extended Range Operation  
The HGA51G-DIR30 directional antenna is  
an accessory for Emerge wireless extenders,  
which are factory-equipped with omni-  
directional antennas. Directional antennas  
provide extended range operation by focusing  
the energy of radio waves into an intensified  
directional beam. Extended distance operation  
requires installation of at least one directional  
antenna onto a transmitter and one onto a  
receiver. Installation of two antennas per unit  
will guard against signal blockage but will not  
increase transmission distance.  
Antenna Head  
(curved face shown)  
Antenna Shaft  
Connector Arm  
Knuckle Joint  
Knurled Fastener  
If the transmitter is to be wall-mounted,  
5
If your wireless extenders are not already  
properly placed and connected to audio, video,  
power and control sources, then please refer  
the appropriate product documentation before  
proceeding with the instructions provided in  
this document.  
arm and antenna shaft are parallel with each other at  
the knuckle joint.  
allow sufficient clearance for the curved  
antenna face to swivel freely in all directions.  
Engage the center socket of the antenna  
3
Repeat steps 2 through 5 for the receiver.  
6
connector arm onto the center pin of the transmitter  
antenna jack. Turn the knurled fastener clockwise  
until finger tight to secure the antenna.  
For best results, position the wireless extenders  
so they are on the same horizontal plane.  
Facing the product, remove the omni-  
1
Using the signal strength LEDs for  
7
directional antenna from the left-hand antenna  
jack on both the transmitter and receiver.  
The antennas loosen from the antenna jack  
by turning the knurled fastener in a counter-  
clockwise manner.  
If the transmitter is to be shelf or rack mounted,  
4
guidance, swivel the curved face of transmitter  
antenna head toward the directional antenna on  
the receiver.  
raise the antenna head such that the antenna  
shaft is pointed upward and perpendicular to the  
connector arm at the knuckle joint. This motion  
requires proper alignment of the knuckle joint,  
which can be accomplished by rotating the antenna  
shaft. Once vertical, swivel the curved antenna face  
toward the intended receiver.  
Using the signal strength LEDs for  
8
guidance, swivel the curved face of receiver  
antenna head toward the directional antenna on  
the transmitter.  
Select either directional antenna and  
2
extend the assembly such that its connector  
To Contact Avocent Technical Support:  
CALL (888) 793-8763 USA or 353-61-715292 Shannon, IR  
Avocent, the Avocent logo, and Emerge are trademarks or registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. ©2007 Avocent Corporation. All rights reserved.  
590-626-501C  
 

3D Innovations Gas Grill UE700 User Manual
Access Handheld TV PTV 7000 User Manual
Acer Personal Computer G510 series User Manual
Acer Projector TravelMate 430 User Manual
Addonics Technologies Electric Heater RT93DAHX User Manual
Agri Fab Spreader 45 02103 101 User Manual
Airlink101 Network Router AP421W User Manual
Alcatel Carrier Internetworking Solutions Telephone 501 User Manual
AMX Stereo Amplifier DAS TAMP4 SIG User Manual
Beckett Water Gardening Outdoor Fountain PL1322 User Manual