Chief Manufacturing TV Mount PCM Series User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Instrucciones de instalación  
Installationsanleitung  
Istruzioni di installazione  
Installatie-instructies  
Instruções de Instalação  
Instructions d´installation  
Plasma Ceiling Mount  
Spanish Product Description  
German Product Description  
Portuguese Product Description  
Italian Product Description  
Dutch Product Description  
French Product Description  
PCM SERIES  
 
Installation Instructions  
PCM SERIES  
TOOLS REQUIRED FOR INSTALLATION AND PARTS  
3/16" (provided)  
A (1)  
B (1)  
I/M  
C (1)  
D (6)  
x1  
DIMENSIONS  
Figure 1  
3
 
PCM SERIES  
Installation Instructions  
Mount Assembly and Installation  
Display Installation  
1. Fold tube out until tube mounting bracket rests against  
faceplate mounting bracket. (See Figure 2)  
If the mounting pattern of the display being installed is a VESA  
standard 200 x 200 pattern the mounting buttons can be  
installed directly to the back of the display. If the display has any  
other mounting pattern an interface bracket must be obtained  
before proceeding. Consult a Chief Customer Service  
representative if an interface bracket is required by calling  
2. Secure tube to faceplate mounting bracket using 3/16" hex  
wrench (C) and two 5/16-18 x 1/2" button head cap screws  
(D).  
3. Tighten all hardware.  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY  
OR DAMAGE TO EQUIPMENT. Displays can weigh in  
excess of 40 lbs (18.1kg). ALWAYS use two people and  
proper lifting techniques when installing display.  
1
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY  
OR DAMAGE TO EQUIPMENT. Make sure mounting buttons  
on display are properly seated in mounting holes in faceplate.  
To install display:  
1. While supporting both sides of display, align four mounting  
buttons on display or interface bracket with four mounting  
holes in faceplate. (See Figure 4)  
2. Lower display into place listening for audible "click" to  
ensure recessed area of mounting buttons are properly  
seated in lower area of mounting holes and "click lock"  
mechanism has engaged. (See Figure 4) and  
(See Figure 5)  
(D) x 2  
2
Figure 2  
4. Thread the tube assembly (A) onto 1-1/2” NPT.  
NOTE: The product is suitable for use with a Listed ceiling  
plate which can accommodate 1-1/2" NPT pipe, and  
has a rated weight capacity of 200 lbs (91 kg).  
5. Secure faceplate (B) to faceplate mounting bracket using  
3/16" hex wrench (C) and four 5/16-18 x 1/2" button head  
cap screws (D).  
1
(A) x1  
(B) x 1  
2
Figure 4  
(D) x4  
5
NOTE: Holes are provided in the faceplate for use with a  
padlock or similar locking device, if desired. In addition,  
the pin and nut may be removed from the upper holes  
and moved to the lower holes for use as a more  
permanent locking device. (See Figure 5)  
Figure 3  
4
 
Installation Instructions  
PCM SERIES  
Display Roll Adjustment  
To adjust display roll:  
1. Loosen 3/8-16 Nylock nut. (See Figure 7)  
To use as a  
more permanent  
lock, remove pin  
and nuts and move  
to lower holes  
2. Adjust faceplate to desired position. (See Figure 7)  
3. Tighten 3/8-16 Nylock nut. (See Figure 7)  
1
2
1
A padlock or bolt may  
be placed through latch holes  
Figure 5  
2
3
Adjustments  
The PCM is designed to accommodate 5" of display height  
adjustment, 4º right and left display roll adjustment, and 15º  
down/5º up display pitch (Tilt) adjustment.  
Remove display before performing adjustments.  
Figure 7  
Display Height Adjustment  
To adjust display height:  
Display Pitch (Tilt) Adjustment  
To adjust display pitch:  
1. Loosen four 5/16-18 button head cap screws using 3/16"  
hex wrench (C). (See Figure 6)  
2. Adjust faceplate to desired position. (See Figure 6)  
3. Tighten four 5/16-18 button head cap screws using 3/16"  
hex wrench (C). (See Figure 6)  
1. Loosen four 5/16-18 button head cap screws.  
(See Figure 8)  
2. Adjust to desired tilt position. (See Figure 8)  
3. Tighten four 5/16-18 button head cap screws.  
(See Figure 8)  
1
3
1
2
3
2
Figure 8  
Figure 6  
5
 
PCM SERIES  
Installation Instructions  
6
 
Installation Instructions  
PCM SERIES  
7
 
PCM SERIES  
Installation Instructions  
Chief® and ClickConnect™ are trademarks of Milestone AV Technologies, Inc. All rights reserved.  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
Chief Manufacturing, a division of  
Milestone AV Technologies  
+31 (0)40 2668615  
Asia Pacific  
A
Room 24F, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA.  
8805-000114 RevE  
©2008 Milestone AV Technologies  
04/08  
P
F
+86-755-8996 9226  
+86-755-8996 9217  
 

Belkin Switch PRO2 User Manual
BenQ Computer Monitor GW2255 User Manual
Blue Rhino Charcoal Grill 253594 User Manual
Blue Rhino Gas Grill GTC1000W C User Manual
Bogen Telephone LUMDMU User Manual
Briggs Stratton Blower 31F700 Series User Manual
Brother Printer PT 1400 User Manual
Bushnell Hunting Equipment 98 0703 12 05 User Manual
CDA Range RV 1001 User Manual
Century Vacuum Cleaner WDV10 User Manual